What is the Axle code for a GMC?

GM RPO Axle Code List (F) The following is a complete list of GM RPO axle codes for Chevy and GMC vehicles starting with the letter F. RPO. Axle Type. Ratio. F16. Transaxle. 2.53. F17.

When did Chevy start using Dana axles in cars?

These axles have been used optionally in production with Dana design axles from 1977 thru 1980. Positive identification of the Corporation (Chevrolet) axle versus the Dana axle is necessary for proper selection and ordering of service replacement parts.

What kind of Axle code does GM RPO have?

GM RPO Axle Code Notes RPO Axle Type G76 Rear Axle (Posi) G80 Positraction G81 Positraction (Rear) G86 Limited Slip (Rear)

Where to find the axle identifica on a Chevy?

#) (Date) Corporation axle identifica– tion is located on axle tube between the Steering Shock Absorber Bracket and the Spring Mount Pad. Commonly 3 character alpha ident code plus 4 digit numeric Julian date code. EXAMPLE YAG XXXX

Where can I Find my GM trouble code?

If you own a 1982 to 1995 GM car or truck, you just might be able to read your trouble codes for free! If you have a connector like this under your dash, read on… (note: this connector may have a black plastic cover over it, so also look for a cover shaped like this, sorry for the messy wires here)

What does code 12 mean on GM OBD?

The system will enter the diagnostic mode. In this mode, the computer will display a Code 12, three consecutive times, by flashing the “CHECK ENGINE”, “SERVICE ENGINE SOON” or “MALFUNCTION INDICATOR LAMP” or light. A Code 12 consists of one flash, a short pause, then two flashes in rapid succession.

Where can I find the GM OBD1 code?

GM OBD1 Codes 13 O2 sensor or circuit 14 coolant sensor/high temp 15 coolant temp/low temp 16 system voltage high (3.8L) DIS circuit 17 crank signal circuit ECM fault crank pos

What are the diagnostic codes for a Chevy?

1 Refer to our Generic OBD II code list for definitions on all other Chevy diagnostic trouble codes. 2 Manufacturer Specific Codes 3 P0342 4 P1031 5 P1032 6 P1105 7 P1106 8 P1107 9 P1108 10 P1109

What are the GM trouble codes for 2008?

Here is what I have done since Aug. 2008 I have replaced the MAF sensor, air filter, knock sensor, fuel pump, coil, tps, fuel filter, distributor cap and rotor. But guess what I am still having the same codes in this order P0327,P0171, and P0174.

When is the p0452 Chevrolet code detected?

The cost of diagnosing the P0452 CHEVROLET code is 1.0 hour of labor. The auto repair labor rates vary widely across the country, and even within the same city. Most auto repairs shops charge between $75 and $150 per hour. When is the P0452 CHEVROLET code detected? An excessively low voltage from the sensor is sent to Engine Control Module (ECM).

Where is the trouble code on a GMC?

When retrieving GMC trouble codes with an OBD II scan tool, proceed as follows: 1. Connect scan tool to the 16-pin data link connector (DLC) located underneath the steering column. The connector may have a removable cover. 2. Turn the ignition on.

Which is the diagnostic code for a GMC check engine light?

1 Refer to our Generic OBD II code list for definitions on all other GMC diagnostic trouble codes. 2 Manufacturer Specific Codes 3 P1031 4 P1032 5 P1105 6 P1106 7 P1107 8 P1108 9 P1109 10 P1111

What kind of engine does a Chevy K2500 have?

Short-bed Sportsides have a more sporty appearance and, with a larger V8, move impressively. A K2500 4×4 with 5.7-liter V8 and automatic averaged 13.3 mpg, and yielded strong low-end pulling power as well as good passing response. Braking can be a problem with rear antilocking, when the bed is unladen.

What kind of engine was in 1990 Chevy C / K?

The 7.4-liter V8 engine was revised, and could be mated to a 4-speed automatic instead of the prior 3-speed. In the 454 SS, that engine now made 255 horsepower–25 more than in 1990. 1992 C/K Pickup. Sportside trucks with the flare-fendered cargo box could have an extended cab this year.

How is the Chevy k1500 Suburban engine rated?

Rated 4 out of 5 by joe shadetree from 99 Chevy K1500 Suburban “Motor not ready to run” Had a couple of minor issues as to why 4 stars, Jegs and ATK customer service are excellent and helped every way they could. I recommend checking compression on all cylinders, verifying top dead center on #1 cylinder and lash on valves prior to install.

What kind of drive does a Chevy C / K have?

All 4-wheel-drive models used Insta-Trac, an on-demand, part-time 4WD system. 4WD trucks had shift-on-the-fly capability and automatic-locking hubs. Four-speed manual gearboxes departed in 1992, when a 190-horsepower turbodiesel V8 debuted for heavy-duty use.

What’s the axle ratio on a GM transaxle?

GM RPO Codes – Factory Identification Labels and Interpretation RPO Code Description Ratio G11 Transaxle Final Drive 2.56 G44 Axle Rear 3.07 G72 Axle Rear 2.14 G75 Axle Rear 3.62

Can you sell a GM Dana 60 front axle?

You are on the right website if you need a used GM Dana 60 front axle for sale. Did you know this shaft is installed in the front and rear of a vehicle?

What is the RPO code for a GM transaxle?

GM RPO Axle Code List (G) RPO Axle Type Ratio G11 Transaxle 2.56 G44 Rear Axle 3.07 G72 Rear Axle 2.14 G75 Rear Axle 3.62

What is the GM RPO code for rear axle?

(Accurate identification using the GM RPO code assumes that the rear end has not been previously modified) The prefix is usually F, G or H when referring to Axle Identification. The list below is a partial list of typical GM RPO Codes, specifically the codes pertaining to Axle Identification, Differential Type and Gear Ratio.

Where can I find the axle gear ratio?

GM RPO Axle Codes. To find the axle gear ratio of any GM vehicle, locate the RPO sticker (typically located in the glove box) and write down any codes starting with F, G, or H. Then, find those codes in the table below.