Other

What does low rpm mean on a GMC Truck?

What does low rpm mean on a GMC Truck?

Lower counts indicate that less air is commanded by the control module. This DTC is designed to detect low engine RPM that is not responding to increased IAC counts. AllOffTopic.com FTW!

How much gas is left in a GMC Truck?

Back in a truck! seafoam that shit bro. 1 can in fuel tank with 4-5 gallons of gas left, half can in brake booster, half can in intake. turn it off for 10 minutes. start it up, floor out pedal to the metal to the gas station to get more gas, laying pure white and black smoke all the way to the gas station. fill it up and ur good to go.

What should the idle speed be on a GMC V8?

A V8 should idle at 500rpm. GoNDown, did you recently disconnect your battery? After I left mine dead in the yard for a while and didn’t charge it, when I started it up it ran like you describe for a few days and then it was fine. I think it was doing a crank relearn (I no longer remember why I came up with that theory, though).

Lower counts indicate that less air is commanded by the control module. This DTC is designed to detect low engine RPM that is not responding to increased IAC counts. AllOffTopic.com FTW!

What should I replace on my 1998 Chevy k1500?

Here is what has been replaced to try and stop this misfire: spark plugs, spark plug wires twice, distributor cap twice, rotor, ignition coil, EGR, CTS on intake manifold, coolant temp gauge sender, fuel filter, fuel pump, MAF sensor, oil change.

When to check your distributor rotor and cap?

Engine misfires can occur for a number of reasons. Checking your distributor rotor and cap to see if they need to be replaced is one way to ensure that everything is in solid working order. 2. Car doesn’t start

What makes a 1998 GMC C2500 no start?

1998 GMC C1500, C2500, C3500 Pick Up. 1998 GMC K1500, K2500, K3500 Pick Up. All of the information you need to diagnose a misfire or a no-start problem (caused by the ignition coil, the ignition module, or the crankshaft position sensor).

Here is what has been replaced to try and stop this misfire: spark plugs, spark plug wires twice, distributor cap twice, rotor, ignition coil, EGR, CTS on intake manifold, coolant temp gauge sender, fuel filter, fuel pump, MAF sensor, oil change.

Engine misfires can occur for a number of reasons. Checking your distributor rotor and cap to see if they need to be replaced is one way to ensure that everything is in solid working order. 2. Car doesn’t start

Why does my GMC Sierra 1500 run rough at idle?

The spray smoothing out the rough rpm is an indication of the engine running lean, could be low fuel pressure, could be a vacuum leak. With it running rough at an idle and smoothing out at a higher rpm is a general sign of a vacuum leak.

What does the fuel smell like in a GMC Sierra 1500?

If so pull the air filter off and sniff the throttle body for a fuel smell. If the diaphragm has ruptured it will literally be like putting a hose with fuel into the intake and running it full.

What happens when the diaphragm is ruptured on a GMC Sierra?

If the diaphragm has ruptured it will literally be like putting a hose with fuel into the intake and running it full. When it initially started to go it probably slowly flooded the engine to where it seemed to run ok but the excess fuel created a ton of carbon coating the O2 sensor. Since no air could pass through it, it gave a false lean reading.

What are the symptoms of a bad intake manifold gasket?

Symptoms of a Bad Intake Manifold Gasket – Chevy 4.3L 1 Engine misfires 2 Sluggish acceleration, lack of power 3 Lean or rich air to fuel ratios 4 Engine overheating 5 Low coolant light illuminating 6 Leaking coolant / dripping onto garage floor More

What happens when intake manifold pressure is low?

Lack of power. A MAP sensor that measures low intake manifold pressure indicates low engine load to the PCM. The PCM responds by reducing the amount of fuel being injected into the engine. While you may notice an increase in fuel economy, you will also notice that your engine isn’t as powerful as it was before.

What does vacuum mean on an intake manifold?

At a perfect vacuum, the MAP sensor will read 0 psi. When the engine is running, the downward motion of the pistons create a vacuum inside the intake manifold (For the purposes of engine control, when a technician says vacuum, what they are really saying is pressure that is less than atmospheric pressure).

What causes an intake gasket on a Vortec to leak?

Leaking Intake Manifold Gasket The intake gaskets on the LB4 and L35 vortec’s are very prone to going bad which results in engine leaks, overheating, stalling, etc. The intake gasket sits between the intake manifold and the cylinder head. It is responsible for sealing engine vacuum, and also engine coolant.

Author Image
Ruth Doyle