How to replace the water pump in a Chrysler Sebring?

Remove the camshaft sprockets and the cover to the rear timing belt. Loosen and remove the water pump bolts and remove the water pump from the engine. Clean all the mating surfaces and install the new water pump with a new o-ring, making sure that the o-ring is seated correctly in the groove before you tighten the bolts.

How do you take a water pump out of an engine?

Place a drain pan underneath the radiator. When the engine is cool, drain the cooling system from the radiator into the pan. Remove the timing chain cover along with the timing chain and its guides. Loosen and remove the water pump bolts and take the pump out of the engine.

What happens if you drain the radiator in a Chrysler Sebring?

Never attempt to drain the radiator when the engine in your Chrysler Sebring is hot. The steam and the hot coolant within the radiator can cause serious burns. Never leave antifreeze open or in puddles. Cats and dogs are attracted to the ethylene glycol in the antifreeze and if they drink it, it could be fatal.

Is there a 2.7 engine problem on a Sebring?

The 2.7 in the LA area for a 2002 Sebring convertible is near impossible. They fixed Chrysler sludge problem. My car runs quiet and smooth. It cost me $2000 for the machine work and rebuild parts. The did it all.

When did the Chrysler 2.7 engine come out?

Chrysler 2.7 Engine Problems – Here’s What You Need To Know! The 2.7 L; 167.0 cu in (2,736 cc) came on the automotive scene back in 1998 and is manufactured in Kenosha, Wisconsin. With a DOHC 24-valve design, is an aluminum block accompanied by cast-iron cylinder liners and aluminum heads.

Can you change the timing belt on a water pump?

The timing belt uses the water pump as a pulley, so you should change the two parts simultaneously. With a little mechanical knowledge and the right tools and replacement parts, installing a new water pump isn’t too difficult.

What should I do if my Sebring is stalling?

Everything else is still on like the radio and everything and the local mechanic and the dealer said that without the check engine light coming on its hard to tell whats wrong. I have replaced Fuel pump, auto shutdown relay, some sort of fuel relay, and catylic converter. Throttle body was also cleaned.

Where is the timing belt and water pump?

The fan belt and power steering belt sit beside the cover which houses the timing belt and water pump, so you’ll need to remove them first. Follow the steps below to remove the belts: Loosen the bolts which hold the alternator in position. Then tap it gently to loosen the fan belt so you can remove it.

What’s the best way to replace a water pump?

Pay attention to the length of the bolts as you remove them because they might not all be the same. Use a scraper or Brillo pad to make sure all surfaces, including the pump mounting surfaces, are clean and free of old water pump gasket material and adhesives before reassembly.

How do you remove a water pump from a car?

Remove the accessory drive belts and the crankshaft damper. Support the engine and remove the right engine mount, the upper left timing belt cover, the upper right timing belt cover and the lower timing belt cover. Then remove the timing belt and tensioner. Remove the water pump from the water inlet pipe.

How much does it cost to replace a Chrysler water pump?

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing. Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM. Chrysler Sebring Water Pump Replacement costs $654 on average.

How is a water pump replaced on a Chevy Cruze?

To replace the water pump, the cooling system is drained and the fan belt or timing belt and pulleys are removed. Depending on which belt drives the pump, that belt and other related components will be removed, followed by the pump itself. Engine surfaces are cleaned, a new water pump and gasket are installed, and the cooling system is refilled.

How to replace a 2.7 water pump in a Dodge?

Remove the upper radiator support, and drain the coolant. Disconnect the battery, remove the air filter assembly, intake plenum, upper engine wiring harness, cooling fans, and upper radiator hose. Check and replace the lower radiator hose if needed. This is also a good time to inspect the trans cooler lines for leaks. One…. Two…. Three….

How do you remove flywheel housing on Cummins MerCruiser?

A). New design mounts have a knurled bottom edge (see Fig. B). Refer to the appropriate Mercury, MerCruiser or Cummins MerCruiser Diesel Service Manual and remove the flywheel housing. Remove the flywheel housing (rear engine) mounts and mount spacers using a suitable mandrel and press (see Fig. C).

Where is the water pump on a 2.7 engine?

An error occurred while retrieving sharing information. Please try again later. The 2.7 engine has both the timing chain and the water pump on the inside of the engine. To access it, it is required to remove the timing chain cover, which also acts as an engine mount, mounting the engine to the frame of the car.

Is the water pump on a Chrysler Sebring bad?

The water pump is the heart of the Chrysler Sebring’s cooling system, circulating the coolant. Serious damage can be done to the engine of your Chrysler Sebring by not changing out a faulty water pump.

Where is the water pump on a Chrysler 2.7?

Please try again later. The 2.7 engine has both the timing chain and the water pump on the inside of the engine. To access it, it is required to remove the timing chain cover, which also acts as an engine mount, mounting the engine to the frame of the car. With the mount removed, the engine must be supported by a jackstand placed under the oil pan.

What kind of timing belt does a Sebring convertible have?

1996 to 2000 Chrysler Sebring Convertible, TIMING BELT & WATER PUMP 1 of 4 – YouTube How to on changing the water pump and timing belt of the 1996 to 2000 Chrysler Sebring convertible with the 2.5 Mitsubishi engine.Chrysler Sebring JXI 1999 C…

How much does it cost to replace water pump on Chrysler Sebring?

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM. Chrysler Sebring Water Pump Replacement costs $654 on average. What is a water pump and how does it work? The water pump is a belt or chain-driven engine accessory bolted to the engine above the crankshaft pulley.

How much does it cost to replace a water pump?

Share it! Know what price you should pay to get your vehicle fixed. The average cost for a Chrysler Sebring water pump replacement is between $767 and $998. Labor costs are estimated between $646 and $816 while parts are priced between $121 and $182. Estimate does not include taxes and fees.

What’s the problem with my Chrysler Sebring not starting?

Now,the car has a knocking and stalling thing going on,and the check engine light is on,and now the car wont start.the previous owner took care of the car. Should I fix or trade??And what am i looking at in terms or repair $$$ We have been having this problem for the past year now and we are getting pretty annoyed.

What happens when water pump goes in Chrysler 2.7L engine?

It’s a terribly designed engine in that when the water pump shaft seal goes (as they are prone to do), the leak dumps coolant into the crankcase and fouls the oil. Chrysler seams to think that a simple weep hole is sufficient to catch any leakage and dump it outside, but, I’ve read too many stories about that being inadequate.

Why is my water pump leaking in my Dodge Intrepid?

I recently helped my sister-in-law by replacing the leaking water pump in her 1998 Dodge Intrepid with the 2.7L engine. It’s a terribly designed engine in that when the water pump shaft seal goes (as they are prone to do), the leak dumps coolant into the crankcase and fouls the oil.

Do you need to replace the timing belt on a water pump?

For applications where the water pump is driven by the timing belt, the timing belt must be removed. Typically, this requires removal of the crankshaft pulley, timing belt covers, and timing belt tensioner. Once the new pump is installed, new coolant is added back while bleeding the cooling system of any air.

How do you remove a timing belt cover?

Support the engine and remove the right engine mount, the upper left timing belt cover, the upper right timing belt cover and the lower timing belt cover. Then remove the timing belt and tensioner. Remove the water pump from the water inlet pipe.

How to replace the water pump in a Chrysler Sebring?