How to replace front drive axle or drive shaft left side?

How to replace front drive axle or drive shaft LEFT side Toyota Corolla. Years 1995 to 2012 – YouTube If playback doesn’t begin shortly, try restarting your device.

When do you need to replace a front axle?

A front axle is a rotating shaft at the front of a vehicle that turns the front wheels. Vehicle design can be quite variable, and axles come in a range of formats and designs to meet different needs. Replacement of a front axle may be necessary in the wake of a serious accident or other damage, like heavy rusting.

What is the front axle on a car?

A front axle is a rotating shaft at the front of a vehicle that turns the front wheels. Vehicle design can be quite variable, and axles come in a range of formats and designs to meet different needs.

How are the wheels of a front drive vehicle connected?

The wheels of your front-drive vehicle are connected to the transaxle via axles that have constant-velocity-type universal joints at each end. There is an inner and outer joint on the left and right axles.

Can a front wheel drive axle be replaced?

Balls and grooves will show wear before the joint fails completely. Replacing a front-wheel-drive axle is straightforward, although physically demanding. Get the replacement axle before you start, as well as a new spindle nut and a cotter pin or two.

How to replace a front axle on a Dodge Ram?

This video covers how to replace a front axle universal joint and a hub or wheel bearing in a 1999 dodge ram 1500 4 wheel drive. Very similar to a 2500. It may be less damaging to loosen the hub bolts and tap on them with a hammer vs the method shown in this vid. Loading…

Which is the drive axle in a car?

A drive axle is an axle in a vehicle which is powered by an engine. People most commonly think of cars when they think about drive axles, with some cars having the front axle driven by the engine, while others have their rear axles driven by the engine.

What happens when your front drive axle fails?

One afternoon, just as you pull out of the parking lot, there’s a loud banging noise and a series of crunches. Then all forward thrust drops off, punctuated by vibration and the occasional ping of tortured metal. Your CV joint has failed.

How are the wheels connected to the transaxle?

Your CV joint has failed. The wheels of your front-drive vehicle are connected to the transaxle via axles that have constant-velocity-type universal joints at each end. There is an inner and outer joint on the left and right axles.

How often do you need to replace drive axle boots?

They should, however, be inspected at least once a year, or more often on high-mileage vehicles or ones that see what manufacturers describe as “severe” service, such as off-road use or transportation-industry conditions.

How do you replace a CV axle in a car?

You can remove the band from the inner boot to help the old axle pass through. Insert the new CV axle into the transmission housing. Just as you removed the old CV axle, insert the new one into the same spot in the transmission housing. The peg will slide all the way in until the axle is flush against the housing.

What’s the best way to change an axle?

By this time, you can put the wheel back on the vehicle (again, the same as you would when changing a tire). After the wheel is on, you can lower the car off the jack and jack stands. Tighten the axle nut. Finally, you can retighten the axle nut once the vehicle is back on the ground.

Where is the outer tie rod on a CV axle?

Unbolt the outer tie rod from steering knuckle. The outer tie rod is literally a rod bolted to the steering knuckle, which is just behind the rotor. This piece will likely be bolted with another 17mm bolt. Like the axle nut, this bolt may be held in place with a cotter pin. Penetrating lubricant may help you more easily remove the pin and bolt.

What should I do if my front drive axle fails?

A failed boot requires immediate disassembly and cleaning, fresh lube and a new boot. This joint shows minor wear. Balls and grooves will show wear before the joint fails completely. Replacing a front-wheel-drive axle is straightforward, although physically demanding.

What causes the left and right axles to fail?

There is an inner and outer joint on the left and right axles. All else being equal, the outer joints fail first because they run with the highest angularity–when the wheel is turned, the joint has to redirect the torque from the engine around a corner. The more angle, the more strain.

How to replace front drive axle or drive shaft LEFT side Toyota Corolla. Years 1995 to 2012 – YouTube If playback doesn’t begin shortly, try restarting your device.

How does a CV axle work on a front wheel drive car?

A typical inner CV joint has three rollers on a tripod (spider) that can slide inside the CV joint housing, so the CV axle can extend or contract as needed. Typical CV axle (shaft) of a front wheel drive car with a Rzeppa outer CV joint and closed tripod-style inner joint. The inner CV joint can work under small angle too.

What kind of joints does a CV axle have?

A CV axle or shaft has two constant-velocity or CV joints: inner and outer. A typical inner CV joint has three rollers on a tripod (spider) that can slide inside the CV joint housing, so the CV axle can extend or contract as needed. Typical CV axle (shaft) of a front wheel drive car with a Rzeppa outer CV joint and closed tripod-style inner joint.

How do you change the axle on a Dodge Grand Caravan?

Hit the end of the tool with a hammer to separate the knuckle from the control arm. Lift up on the wheel hub assembly and push it to the right while pulling the axle out fo the hub assembly. Pry the other end of the axle out of the transmission with a small flat-tip screwdriver.

When do you need to replace the front axle on a Jeep Grand Cherokee?

The axle has two joints, called CV joints, that flex and allow the axle mobility when turning and going over bumps in the road. When the axle fails, it is usually because of CV joint failure. This often presents itself as a clicking or grinding noise when you make turns. When this happens, you must replace your Grand Cherokee’s front axle.

How to replace front drive axle or drive shaft left side?