How to remove cam position sensor from V6 Mustang?

Disconnect battery ground cable (14301) . Disconnect fuel charging wiring (9D930) from distributor stator (12A112) (camshaft position sensor). Remove stator camshaft position sensor retaining screws and distributor stator (camshaft position sensor) from camshaft position sensor housing.

What happens if the cam position sensor is not correct?

CAUTION: If stator (camshaft position sensor) electrical connector is not positioned properly (for example, contacting the A/C compressor bracket), DO NOT reposition the connector by rotating the camshaft position sensor housing. This will result in the fuel system being out of time with the engine, possibly causing engine damage.

How do you install a camshaft position sensor?

Remove the camshaft position sensor housing and repeat installation procedure, beginning with Step 1. Install distributor stator (camshaft position sensor) and retaining screws. Tighten screws to 2.5-3.5 Nm (22-31 lb-in). Connect fuel charging wiring connector to distributor stator (camshaft position sensor). Connect battery ground cable .

Which is the best body cam for a 85-95 Mustang?

This Ford Performance B303 hydraulic roller camshaft, also known as an B cam, is a great way to add horsepower to your 5.0L 85-95 Mustang. Fox Body cams not only add performance, they give your Mustang an aggressive lope exhaust tone. This Mustang B Cam offers a more aggressive idle and excellent low-end torque for your 302 Fox Body engine.

Where is the camshaft sensor on a Chilton car?

The left side head sensor is obvious behind the steering pump reservoir. The right side sensor is not in the same position. Perhaps The Chilton manual Ihave does a poor job of showing the location. It also does not confirm that the right side of engine is bank A. helpful?

Where can I buy a synchronizer for a Mustang?

Bought a rebuilt motorcraft Synchronizer and sensor for 150 bucks from Napa and had the local shop instal and sync it with the special tool for 100 bucks. 200 miles and the light is still off. www.rpm-mustangs.com has great install instructions on their site forinstalling without the tool.

What happens if the cam position sensor is out of sync?

Failure to follow this procedure will result in improper stator (camshaft position sensor) alignment. This will result in the fuel system being out of time with the engine, possibly causing engine damage. Engage camshaft position sensor housing vane into the radial slot of the tool.

How to remove the camshaft synchronizer on a Ford Ranger?

It will show the location of the camshaft synchronizer, the removal process, and the installation. Note, before removing the camshaft synchronizer, make sure you mark the location of the housing and tab with a magic marker to ensure the replacement camshaft synchronizer goes in exactly the same way. Loading…

How do you install a CMP sensor on a car?

When installing the sensor, the connection must be in the exact same position. Position the No. 1 cylinder at 10°ATDC, then matchmark the CMP sensor terminal connector position with the engine assembly. Remove the camshaft position sensor retaining screws and sensor. Remove the retaining bolt and hold-down clamp.

What to use to replace distributor position sensor?

CAUTION: If the replacement distributor stator (camshaft position sensor) does not contain a plastic locator cover tool, a special service tool such as Syncro Positioning Tool T89P-12200-A must be obtained prior to installation of the replacement distributor stator (camshaft position sensor).

What’s the value of a 2001 Ford Mustang?

There aren’t any 2001 Ford Mustang for sale near you. 2001 Ford Mustang appraisal values can range from $503 – $1,786. Find out what your car is really worth in minutes. I LOVE my SVT Cobra!!!!!!

What to do if your camshaft sensor is not correct?

Install hold-down clamp and retaining bolt and tighten bolt to 20-30 Nm (15-22 lb-ft). CAUTION: If stator (camshaft position sensor) electrical connector is not positioned properly (for example, contacting the A/C compressor bracket), DO NOT reposition the connector by rotating the camshaft position sensor housing.

Why was there a 3.8 liter V-6 in the 2004 Mustang?

Simply put, Ford hadn’t planned or produced enough 3.8-liter V-6’s to get through the model 2004 year and needed something to connect the dots between the rest of ‘04 to the all-new Mustang bowing for 2005 (itself destined for a much re-engineered 4.0-liter V-6, now a single-overhead-camshaft version of the 60-degree “Cologne” family V-6).

What’s the horsepower of a 1994 Mustang V6?

In 1994, this V6 put out 145 horsepower and 215 lb.-ft. of torque. Though the horsepower numbers changed throughout the SN95 generation, it maxed out at 193 hp. If you’re looking to add some more power to your 3.8L engine, here are a few mods that can give your V6 better performance.

How to increase the horsepower of a Mustang V6?

A decent cat-back exhaust, which replaces the exhaust aft of the catalytic converter to retain emissions compliance, will unleash even more power. Another option is installing a tubular header in place of the restrictive stock manifold. The more fresh, cold air your Mustang V6 gets, the more powerful it will be.

How do you install a coil pack on a Mustang?

1. Remove negative cable from battery using 5/16 socket and secure away from negative terminal. 2. Remove wire harness from coil & throttle cable coupling. A. Use a flat head screwdriver to help by gently lifting on tab as this clip can easily break. B. Pull coupling straight off bolt. 3.

Where can I find a Ford Mustang 6 cylinder?

Six-cylinder Mustang owners can also check out the Mustang 6 Association ( www.mustang6association.org) to mingle with owners of both the inline and V-6 Mustangs over the years.

How to remove cam position sensor from V6 Mustang?