How to press out a bad ball joint?

Ball joint press. Learn how to press a lower ball joint by using a ball joint press. I show you in depth how to press out a bad ball joint and press in a new ball joint. I go through what adapters to use, how to use them, how to properly press the ball joint in and out without damaging it, and give you tips and tricks along the way.

How can I check the condition of my ball joints?

In order to check the condition of the ball joints, you need to jack the car and shake the control arm. There shouldn’t be any wheel play. The grease fitting shouldn’t wiggle either. While you are there, check the seal too. It should be intact. Keep in mind that these are only the basics of how to check the ball joints.

When do ball joints need to be replaced?

As a rule of thumb… It’s good to check the ball joints regularly and never ignore any of the signs indicating there is a problem with them. If ball joints are not replaced in time, they might break disconnecting the wheel from the chassis. So, keep in mind the reasons why do ball joints go bad for safe driving.

How to replace a lower control arm ball joint?

Replacing a Lower Control Arm Ball Joint. Learn how to replace a lower ball joint by pressing it out of the control arm and pressing the new one back in. To watch the longer, in depth version, click the link below. Press out a Ball Joint (In-depth): https://www.youtube.com/watch?v=ZztbA…

Where can I buy ball joint NUT and bolt?

Nut & Bolt Assortment Sets Hardware Nuts Automotive Performance Parts & Accessories Powersports Body Parts Automotive Parts & Accessories Industrial & Scientific Tools & Home Improvement Electronics Garden & Outdoor

How to install a ball joint with a pinch bolt?

To learn more about servicing ball joints and steering and suspension repairs, visit Garage Gurus fmgaragegurus.com.Installing a ball joint with a pinch bolt… AboutPressCopyrightContact usCreatorsAdvertiseDevelopersTermsPrivacyPolicy & SafetyHow YouTube worksTest new features

How to tell if a ball joint is bad?

Learn how to diagnose a bad ball joint for both an upper and lower control arm. I also quickly show you how to tell if it is a bad tie rod, bushings, or a bad bearing just in case your ball joint is not bad. A bad ball joint will make noise which is the first symptom of knowing it’s bad.

Why are ball joints important to a vehicle?

Because ball joints are an important component of any vehicle’s suspension. When they begin to have problems or fail, the overall handling and ride characteristics of the vehicle are likely compromised.

Which is the best ball joint press to buy?

For the best picks of ball joint presses, here are the 10 best ball joint presses reviews to check out. #10. Orion Motor Tech Heavy-Duty Ball Joint Press #9. Orion Motor Tech 5 Pieces Joint Ball Joint Presses #8. Astro Pneumatic Tool Master Ball Joint Presses #7. Astro Pneumatic Tool Ball Joint C-Frame Press #6. FAERSI 21 Pieces Ball Joint Press

How do you replace a ball joint in AutoZone?

Carefully inspect and remove any snap rings that may be securing the ball joint in place. Using a ball joint press, press the old joint out of the control arm. Using the ball joint press, press the new joint into the control arm. Tip – throw your new ball joints in the freezer overnight before installation.

Are there ball joints that can be replaced?

Some ball joints are built directly into the Control Arm and are not replaceable. Others are, either by being pressed, bolted, or riveted in. Most front-wheel-drive vehicles have only 2 lower ball joints on each side, as the upper pivot-point is accomplished by the strut assembly.

How to replace upper control arm ball joint?

Upper Ball Joint Replacement. This video will show you how to replace the Upper Control Arm Ball Joint on a Chevy Trailblazer, GMC Envoy, etc. Replacing a ball joint is fast and easy and can be done with basic hand tools and a ball joint press you can rent for free at your local parts store.

What does it mean when your ball joints are not working?

Grasp the top and bottom of the tyre and rock it in and out along the wheel’s vehicle axis. If the ball joints are working well, there should be little to no play in this movement. Noise and play from the top – this indicates a problem with the upper ball joint. Noise and play from the bottom – this suggests a problem with the lower ball joint.

Is it easy to replace a ball joint?

Replacing a ball joint is fast and easy and can be done with basic hand tools and a ball joint press you can rent for free at your local parts store. This ball joint is pressed but some are bolt on which is even easier.

How can I check the ball joint on my car?

Figure out if your vehicle’s got a strut-style suspension or a control arm, then check the ball joint by either jacking up the control arm near the ball joint to check for wheel play, or by jacking up the car and using a pry-bar to check for wheel play in a strut-style suspension.

Where can I get a replacement ball joint?

Purchase the correct replacement ball joint assembly for your vehicle. Go to the auto parts store and get a replacement part appropriate for your make and model. All you’ve got to know is the type of vehicle and you should be able to use the guidebook in the aisle, or ask for help and they’ll be able to direct you.

How do you install a lower ball joint?

Place the floor jack under the lower control arm as close to the ball joint as possible without interfering with its removal. Strike the ball joint stud with one good blow with a hammer and the ball joint will come out downward. Install the lower ball joint using the ball joint installer kit.

Where are the ball joints on a car?

They are used on the lower control arm to secure the spindle to the arm and allow the spindle to turn or swivel. An extremely worn ball joint can obviously cause a catastrophic incident where it separates and causes a total loss of control of the vehicle.

Is it safe to remove the lower ball joint?

On a strut type of front suspension, it is safe to remove the lower ball joint without supporting the arm because there is no spring tension on the arm. Once the ball joint is loose, push the lower arm down and with the other hand swing the spindle off of the ball joint and let the spindle sit to the side of the lower arm.

What happens when a front ball joint fails?

Should a ball joint break, the wheel becomes totally free to move in any direction, which can damage the car’s fender, tire, and several suspension components, if not more. Usually, when front ball joints start to fail, the vehicle will display a few symptoms that alert the driver a problem has occurred.

Why do you need to replace ball joints in your car?

They connect the control arm to the steering knuckles and allow for smooth and solid movement in the suspension. The front suspension of most cars has at least lower ball joints and in some cases upper ones as well. Why replace ball joints?

Why is my lower ball joint not working?

The lubrication finally dries out, water intrudes inside the boot covering the moving parts, and rust and abrasive road dirt turn a ball joint or tie rod end into a loosey-goosey accident waiting to happen. Do not delay in repairing a failing ball joint or tie rod end.

How to press out a bad ball joint?