How much torque does a pinion nut have?

It takes about 300 foot pounds to crush the sleeve initially. After it has been properly crushed (by checking the rotating resistance of 19-22 inch pounds on the pinion) there should be at least 150 pounds torque on the pinion nut (or else you pull it apart get another crush sleeve and start over).

How big is the torque cap on a pinion?

Pinion Preload (Reused) Ring Gear Backlash Ring Gear Bolt Torque Carrier Bearing Cap Bolts Chrysler 7.25″ 12 to 14 in-lbs. 6 to 7 in-lbs. .006″ to .010″ 55 ft-lbs.

How to torque the rear end yoke on a Camaro?

Richmond gear sells them for about $25 bucks. I have also fabricated up a spanner out of 1/4″ plate that is welded into a six foot pipe that bolts to the rear yoke. I then strap the pipe to the axle and have my assistant sit on the end while I torque the nut. ‘Larger Dave’ is giving you the Rotational Pre-Load for the pinion.

How big should the pinion nut be on a Camaro?

19-22 inch pounds is what it needs to be! Of course I’m talking about the bearing preload on a properly torqued pinion nut will yield that value as the nut rotates. It takes about 300 foot pounds to crush the sleeve initially.

How much torque does a rear spindle nut Torq have?

Put the wheel on and torque the lug nuts to 140 lb-ft then (after the lug nuts are tight) torque the axle bolts to 70-85 lb-ft. Eight clicks is about a 1/4 turn.

The pinion nut does not have a torque spec. as in how tight the nut is. The amount of torque is measured in bearing preload. You will need a “torque to rotate” torque wrench. If you are using new bearings the torque spec. is 15-25 in. lbs. If you are using your old bearings the torque spec. is 10-20 in. lbs to rotate.

What are torque specs for rear axle bearing nut?

Torque specs for rear axle bearing hub & axle nut on 2006 dodge magnum sxt. Go to autozone dot com and make a free account, put in the year and make and model then look for the free repair guides. They are online Chilton books and they will have it.

What do I torque the pinion to on my 2012 Ram 3500 I?

I am repearing 2001 dodge ram 1500 9.25 diferential.Ihave it back together/ but the pinion has has some forward and back play. Do you think this … read more Vocational, Technical or Tra… Vocational, Technical or Tra… Vocational, Technical or Tra…

How much torque does a Chevy yoke nut need?

The inch lb torque rating is not how much you torque the nut. You could easily put 300 ft lbs into the nut to crush the sleeve, but then you measure rotational resistance with the inch lb wrench to see how much torque it takes to keep the pinion gear in motion. 20 to 26 inch lbs is often advertised for the parts.

What is the spec on a pinion nut?

If you are talking about the pinion nut it is not hand tighten. The spec measures the torque required to turn the pinion gear by itself once the nut is tightened. The spec is NOT the torque applied to tighten the nut. That is whatever it takes to achieve the pinon bearing pre-load which is determined as described above.

How big should the pinion nut be on a Dodge Ram?

I did the same on my jeep with a d44 rear axle (also uses a crush sleeve), and torqued it back to about 150 ft lbs using the parking brake to hold the axles shafts from spinning. If I were you I would invest in a torque wrench to be sure it is right.

How much torque does a pinion nut have?