How much is a 2004 Yamaha Raptor 660R worth?
How much is a 2004 Yamaha Raptor 660R worth?
Values
| Suggested List Price | Average Retail | |
|---|---|---|
| Base Price | $6,199 | $3,065 |
| Options (Add) | ||
| Total Price | $6,199 | $3,065 |
Does a Raptor 660 have a clutch?
No, the 660 model stopped in 2005. The 2006-2013 Yamaha Raptor is a different atv with a different clutch.
What is the top speed of a 2004 Raptor 660?
Top speed of both is limited electronically at 75 mph (but modifiable).
What is a 2003 Yamaha Raptor 660 worth?
Values
| Suggested List Price | Average Retail | |
|---|---|---|
| Base Price | $6,499 | $2,965 |
| Options (Change) | ||
| Total Price | $6,499 | $2,965 |
Where are Yamaha Raptors made?
the USA
The YFZ450R and Raptor 700 lineup, along with every Yamaha Side-by-Side and full-size ATV, are proudly Assembled in the USA at Yamaha’s state-of-the-art manufacturing facility in Newnan, Georgia for worldwide distribution.
How do you adjust the clutch on a Raptor 350?
- Loosen the locknut at the clutch lever.
- To increase the clutch lever free play, turn the.
- Tighten the locknut at the clutch lever.
- Loosen the locknut at the clutch lever.
- Fully turn the adjusting bolt at the clutch lever.
- Loosen the locknut at the crankcase.
- To increase the clutch lever free play, turn the.
How to install starter clutch on Raptor 660?
1 Remove four bolts to the starter idler cover. Remove the small idler gear and set aside with the cover. 2 Remove the left case cover. Loosen the nine bolts in a criss-cross pattern so as to avoid warping the cover. Once all are loose, remove them.
How big are the clutch bolts on a raptor?
Tighten the bolts in a criss-cross fashion to 11 ft/lbs or 16 N/m. This is critical, you must torque these bolts correctly and evenly!
What should the nut be on a Raptor 660?
Grab your strap wrench and place it on the flywheel and tighten the nut to 110 ft/lbs or 150 N/m. Once again, you may need a helper to hold the rear brake and the bike may need to be in gear. Make sure everything is well lubricated.
Where is 52 tooth idler gear on Raptor 660?
Pull the 52 tooth (large gear behind the flywheel) idler gear off the shaft. If you have a 2001, remove the needle bearing and set aside. You will not reuse this bearing if you purchased a kit. The gear we sent to you is ready to go with a pressed in brass bushing. Check the bearing surface for wear and pitting and replace if worn.
How do you replace clutch on Raptor 660?
Cover the hole (case side) that is open to the transmission to stop debris from entering. Clean both surface carefully and wipe clean with rubbing alcohol. Also clean the shaft surface and make sure all debris is removed. If you removed the wiring harness gasket, put sealant on one side and replace.
Where are the bolts on a raptor starter clutch?
Loosen the nine bolts in a criss-cross pattern so as to avoid warping the cover. Once all are loose, remove them. The bolt farthest to the left is securing the Raptor’s ground wire, so disconnecting the battery is also recommended. You may have to rock the cover back and forth to get it loose.
Grab your strap wrench and place it on the flywheel and tighten the nut to 110 ft/lbs or 150 N/m. Once again, you may need a helper to hold the rear brake and the bike may need to be in gear. Make sure everything is well lubricated.
Pull the 52 tooth (large gear behind the flywheel) idler gear off the shaft. If you have a 2001, remove the needle bearing and set aside. You will not reuse this bearing if you purchased a kit. The gear we sent to you is ready to go with a pressed in brass bushing. Check the bearing surface for wear and pitting and replace if worn.
