How much does it cost to replace water pump on Chevy Silverado?
How much does it cost to replace water pump on Chevy Silverado?
Chevrolet Silverado 2500 HD Water Pump Replacement costs $432 on average. Following is a breakdown of the labor and parts estimates. What is a water pump and how does it work? The water pump is a belt or chain-driven engine accessory bolted to the engine above the crankshaft pulley.
What should I do to my Duramax water pump?
Once you get the fan and cage out of the way its no different then the older duramax’s. Going by the book GM says to pull the starter and install the flywheel holding tool for breaking the balancer bolt loose and tightening it. This is where a lot of the excess time comes in.
How long is the water pump on a GM Truck?
I want to smack the GM engineer in the head who came up with that fan shroud design on the 2006+ trucks. That thing is the devil. Click to expand… Id rather punch the guy who clocked the one water pump housing fastener behind the balancer. Water pump would be a two hour job at most if it had been designed just a hair differently.
Do you have to pull starter on GM water pump?
Going by the book GM says to pull the starter and install the flywheel holding tool for breaking the balancer bolt loose and tightening it. This is where a lot of the excess time comes in. If you get the Lisle tool kit you can shave off an hour or better right there by not having to pull the starter.
Chevrolet Silverado 2500 HD Water Pump Replacement costs $432 on average. Following is a breakdown of the labor and parts estimates. What is a water pump and how does it work? The water pump is a belt or chain-driven engine accessory bolted to the engine above the crankshaft pulley.
Why does my Chevy Silverado water pump keep blowing out?
A seeping water pump is often the cause of coolant odor, and an expansion tank that often needs topping off. Although it may not blow out like a hose, the water pump will get worse. Keep reading and learn how to replace the water pump in your Chevy Silverado right in your driveway with basic tools.
How does a water pump work on an Audi A4?
The pump housing has an impeller that circulates engine coolant through the cooling system passageways in the engine block and cylinder head, on to the radiator, where the coolant temperature is reduced. . The lower temperature coolant then flows back to the water inlet on the engine and the water pump continues the cycle.
How do you replace a water pump on a Buick Allure?
The bolts holding the pump to the engine are removed and the pump is pulled out. The gasket surface must be cleaned and the pump mounting surface inspected. A new gasket, rubber seal, or RTV sealant, as required, is installed and then the new pump. The bolts are torqued in sequence using a calibrated inch pound torque wrench.
A seeping water pump is often the cause of coolant odor, and an expansion tank that often needs topping off. Although it may not blow out like a hose, the water pump will get worse. Keep reading and learn how to replace the water pump in your Chevy Silverado right in your driveway with basic tools.
The pump housing has an impeller that circulates engine coolant through the cooling system passageways in the engine block and cylinder head, on to the radiator, where the coolant temperature is reduced. . The lower temperature coolant then flows back to the water inlet on the engine and the water pump continues the cycle.
The bolts holding the pump to the engine are removed and the pump is pulled out. The gasket surface must be cleaned and the pump mounting surface inspected. A new gasket, rubber seal, or RTV sealant, as required, is installed and then the new pump. The bolts are torqued in sequence using a calibrated inch pound torque wrench.
Once you get the fan and cage out of the way its no different then the older duramax’s. Going by the book GM says to pull the starter and install the flywheel holding tool for breaking the balancer bolt loose and tightening it. This is where a lot of the excess time comes in.
I want to smack the GM engineer in the head who came up with that fan shroud design on the 2006+ trucks. That thing is the devil. Click to expand… Id rather punch the guy who clocked the one water pump housing fastener behind the balancer. Water pump would be a two hour job at most if it had been designed just a hair differently.
Going by the book GM says to pull the starter and install the flywheel holding tool for breaking the balancer bolt loose and tightening it. This is where a lot of the excess time comes in. If you get the Lisle tool kit you can shave off an hour or better right there by not having to pull the starter.
