Other

How do you replace a ball joint on a Chevy Silverado?

How do you replace a ball joint on a Chevy Silverado?

Break the ball joint away from the knuckle with a puller or ball joint separator and remove the nut. Remove the upper control arm’s bolts with the wrench, making sure you know which way the bolts are installed, and remove the control arm. Place the control arm in a bench vise and knock back the ball joint’s crimped areas with a hammer and chisel.

When to replace the lower control arm on a Silverado?

However, if the ball joint has failed, the lower control arm needs to be replaced because this ball joint is not serviceable. Figure 1. Replacement lower control arm for a first generation Silverado 1500. Traditional “wishbone”-type, “A”-shaped front suspensions utilize an upper and lower control arm.

How do you replace lower control arm joint?

With tension now removed from the torsion bar, loosen the 24mm nut at the bottom of the wheel knuckle that holds the lower control arm ball joint in place. Don’t remove the nut, but leave a large gap between the nut and the wheel knuckle. Figure 6.

Where to remove lower control arm nut on Chevy Silverado?

Remove the already-loosened 24mm nut at the bottom of the wheel knuckle. This nut holds the lower control arm ball joint to the knuckle via its threaded stud. With the jack still in place, remove the 35mm wheel nut and the washer behind it from the center of the hub.

Break the ball joint away from the knuckle with a puller or ball joint separator and remove the nut. Remove the upper control arm’s bolts with the wrench, making sure you know which way the bolts are installed, and remove the control arm. Place the control arm in a bench vise and knock back the ball joint’s crimped areas with a hammer and chisel.

How to replace a lower control arm ball joint?

Replacing a Lower Control Arm Ball Joint. Learn how to replace a lower ball joint by pressing it out of the control arm and pressing the new one back in. To watch the longer, in depth version, click the link below. Press out a Ball Joint (In-depth):

Why do you need to replace ball joints on your car?

The ball joints on a vehicle are essentially the main hinges of the suspension, similar to the joints in your shoulders and hips. If the ball joints wear down, it can make the vehicle shake while turning and you need to replace them.

What makes up the lower ball joint on a steering wheel?

The lower ball joint is what attaches the steering knuckle and control arm together. There are two pieces which make up the lower ball joint; a socket and ball. These pieces are inside of a rubber boot that is filled with lubricant. Basically, the lower ball joint allows the wheels and tires to be connected to the vehicle and its steering assembly.

What happens if you don’t replace your ball joint?

If you don’t get the ball joint replaced soon, it will get louder and eventually break off completely. One sign of a lower ball joint that has failed that people don’t often consider is uneven tire wear.

How much does it cost to replace a steering wheel ball joint?

Don’t let your steering wheel continue to wander like this for too long because the problem will only get worse in time. Get the ball joint replaced right away if it ends up being the culprit. The cost to replace the lower ball joint is anywhere from $220 to $290.

With tension now removed from the torsion bar, loosen the 24mm nut at the bottom of the wheel knuckle that holds the lower control arm ball joint in place. Don’t remove the nut, but leave a large gap between the nut and the wheel knuckle. Figure 6.

How do you remove the ball joint from a lawn mower?

Removing the Old Ball Joint Pull the cotter pin and loosen the large castellated nut. The top should look like a crown, or castle, at the bottom. Pop loose the ball joint. The goal is to try to guide it through the hole in the upper half of the steering knuckle. Remove the allen bolts and slide the control arm free.

Remove the already-loosened 24mm nut at the bottom of the wheel knuckle. This nut holds the lower control arm ball joint to the knuckle via its threaded stud. With the jack still in place, remove the 35mm wheel nut and the washer behind it from the center of the hub.

Replacing a Lower Control Arm Ball Joint. Learn how to replace a lower ball joint by pressing it out of the control arm and pressing the new one back in. To watch the longer, in depth version, click the link below. Press out a Ball Joint (In-depth):

Where to remove lower control arm nut on Chevy Silverado?

Author Image
Ruth Doyle