Other

How do you change ignition switch on S-10?

How do you change ignition switch on S-10?

Remove the remaining 8-mm stud that attaches the ignition switch to the steering column. Lift the switch off the push rod that is inserted into a hole in the bottom of the switch. Lay the switch aside. Install the new switch onto the push rod, and secure it to the steering column using one of the 8-mm studs.

How does the ignition work on a 1992 Chevy S10?

As is the case on the 1992 S10 Chevy pickup, the ignition key is simply the theft-deterrent device. Once the key is inserted into the lock cylinder, the tumblers open; you turn the key and this sends an electrical charge from the ignition switch to the ignition coil. From there, all the electrical components are electrically activated.

How do you reinstall an ignition switch on a car?

Reinstall the replacement ignition switch by reversing the removal procedure. When reinstalling the dimmer switch to the column, place a 3/32-inch drill bit into the hole on the dimmer switch. Align the switch to the column and then push it against the actuator rod to secure it in place.

Where is the release pin on an ignition switch?

The new or rebuilt switch should slide easily back into its hole on the steering column. Align the shape of the cylinder and the location of the release pin with the coinciding grooves in the ignition module.

As is the case on the 1992 S10 Chevy pickup, the ignition key is simply the theft-deterrent device. Once the key is inserted into the lock cylinder, the tumblers open; you turn the key and this sends an electrical charge from the ignition switch to the ignition coil. From there, all the electrical components are electrically activated.

Remove the remaining 8-mm stud that attaches the ignition switch to the steering column. Lift the switch off the push rod that is inserted into a hole in the bottom of the switch. Lay the switch aside. Install the new switch onto the push rod, and secure it to the steering column using one of the 8-mm studs.

How do you remove an ignition switch from a car?

Remove the ignition switch from the actuator rod and then unplug the electrical connections of the ignition switch wire harnesses to remove it. Reinstall the replacement ignition switch by reversing the removal procedure. When reinstalling the dimmer switch to the column, place a 3/32-inch drill bit into the hole on the dimmer switch.

What are the symptoms of a bad ignition switch?

Your Chevy S10‘s ignition switch is one of the most vital items on the entire vehicle. If it fails, the entire vehicle won’t be able to run. We’ve compiled some of the most common symptoms of a bad ignition switch. These include stalling issues, not starting, and no power to the radio or accessories.

What should I do if I need to replace my ignition switch?

Reconnect the cable to the negative (-) terminal on the battery, then insert the key into the ignition and turn it to start the vehicle. The vehicle should start without any issue. If it doesn’t, remove the ignition switch and reinstall it. Shut the engine off (if it starts) and disconnect the battery again.

Where is the ignition switch located on a car?

If the switch is suspected, it would need to be fully tested prior to replacement. Your ignition switch is typically located right behind the key cylinder (where you insert your key). This may be in the steering column or in the dash. You will need to remove any covers or dash panels to access the switch.

Can a bad ignition switch cause a Chevy S10 to stall?

Your S10 stalls because the faulty switch turns off the fuel pump or power to the ignition. When this happens, the engine will not be able to run until it gets that signal back. 2. Starts then Dies If your Chevy S10 is starting right up, but then immediately dies, that is a very good indication that the ignition switch is bad.

Where is the ignition switch on a Chevy S10?

The S10’s ignition switchis not what your key goes into. That is called the lock cylinder. The ignition switch typically sits directly behind the lock cylinder. It has three main functions. Power the Accessories- This should be what you get when you turn the key to the first position.

How do you replace a steering wheel switch?

Lift the switch off the push rod that is inserted into a hole in the bottom of the switch. Lay the switch aside. Install the new switch onto the push rod, and secure it to the steering column using one of the 8-mm studs.

Can a Ford Econoline ignition switch be replaced?

The ignition switch in a Ford Econoline E350 van sends an electrical signal to the starter motor when the ignition key is turned. Once the switch fails, you’ll need to replace it. Replacement switches are available from most auto parts stores. The switch and cylinder are one unit and are secured to the steering column with a single retaining pin.

What to do if your key is stuck in the ignition switch?

The key may be stuck in the ignition switch, but that shouldn’t stop you from turning it. If you don’t have a key, you will need to force the module to turn using a flathead screwdriver. Press the release pin inside the hole on the ignition module with a screwdriver.

How to fix ignition problems by replacing the ignition switch?

How to fix ignition problems by replacing the ignition switch. Ignition switch location, inspection, removal and repair. DIY car repair with Scotty Kilmer, an auto mechanic for the last 43 years. 1. Screwdriver set: http://amzn.to/2j92UCG 2. Disposable Gloves: http://amzn.to/2zSRuxO 3. Common Sense 4. Full HD Camera: http://amzn.to/2AvoEk7 5.

Do you have to take steering wheel out to replace ignition switch?

Take the steering wheel out if it’s in the way. In some vehicles, you may be able to replace the ignition switch without removing the steering wheel. However, if you’re unable to get access to the top of the ignition switch with all the interior trim pieces removed, the steering wheel may need to come out.

The new or rebuilt switch should slide easily back into its hole on the steering column. Align the shape of the cylinder and the location of the release pin with the coinciding grooves in the ignition module.

How do you remove a battery from an ignition switch?

Use an appropriate sized wrench to loosen the nut holding the cable on the negative (-) terminal and then slide it off the post. You don’t need to remove the positive cable from its terminal. Tuck the negative cable to the side of the battery to make sure it doesn’t accidentally come into contact with the terminals.

Author Image
Ruth Doyle