How can I Fix my Chevy Silverado ignition?

Wedge a shim in the connection and secure the new connection with hot glue, silicon or any other glue that can be fairly easy to scrap off and remove if further maintenance is required. Replace the steering column cover and that’s how you fix the ignition in your GMC Sierra or Chevy Silverado 1500, 2500 and 3500. Loading…

Is there an easy fix for a GMC ignition switch?

This is one way to fix a very complicated electrical system in the Chevrolet and GMC cars and trucks. Some are easy fixes with loose or bad electrical connections. Others involve the ignition switch itself, and others involve one of the computers that the system communicates with when starting the vehicle.

How to program a Chevy Silverado key fob?

Free Key Fob Remote Programming Instructions for a 2004 Chevrolet Silverado (1500, 2500, 3500) 1 Close All Doors CLOSE all doors. 2 Enter Programming Mode – Step 1 INSERT key into the Ignition (DO NOT TURN). 3 Enter Programming Mode – Step 2 PRESS and HOLD the power UNLOCK button on the Driver’s side door.

How to turn off keyless entry on Chevy Silverado?

HOLD the LOCK and UNLOCK buttons on the remote at the same time until door locks cycle again. This could take up to 30 seconds. Now REPEAT Step 6 for all additional remotes to be programmed, including working ones. After Step 6 has been performed for all remotes TURN ignition to ON to exit programming mode. TURN ignition to OFF, and remove key.

Why does my Chevy Silverado not start up?

Others involve the ignition switch itself, and others involve one of the computers that the system communicates with when starting the vehicle. The security system may have a number of issues, including the installation of a remote starter, causing the car or truck not to start. Most complaints involve a blinking security light.

Is there a problem with the ignition on my GMC Sierra?

This problem occurs in minivans, cars and SUVs as well. There has been more reports of ignition Anti Theft defects and the security light flashing in more cars and trucks. This is one of the easy fixes for the common ignition starting problem, but GM needs to recall this issue and fix it for us.

Why does my Chevy Silverado 1500 lock off?

If your battery is bad or all the doors to your Chevrolet Silverado are not properly closed, the anti-theft lock in your 1500 could be set off.

How to disarm an anti theft lock on a Chevy Silverado?

Chevrolet Silverado: How to Disarm Anti-Theft Lock. 1 Step 1 – Unplug the battery. Pop the hood of your truck to remove the battery. This should be as simple as removing the cables from your battery 2 Step 2 – Lock all doors. 3 Step 3 – Check for trouble codes. 4 Step 4 – Visit your local dealer.

Is there a problem with my Chevy Silverado?

Will turn key and it is like no power from battery to starter, but have lights, radio, etc. Turn key again or sometimes multiple times, to no avail. Then, turn it one more time and it starts. Then the next 15 starts, no problem. Sometimes hot engine, sometimes cold. UPDATE: 2-6-14; I sold the truck to my father. He changed the starter.

What should I change in my Chevy Silverado?

In order to keep it running at its best, you must properly maintain it by changing the oil and filter, as well as replacing parts that wear out. Exhaust System – The Silverado has many sensors that transfer information to the computer.

What are the discounts for a Chevy Silverado?

SHERRELL CHEVROLET, INC. Includes $750 in cash and discounts. SHERRELL CHEVROLET, INC. Includes $750 in cash and discounts. SHERRELL CHEVROLET, INC. Includes $250 in cash and discounts.

How is the transmission on a Chevy Silverado controlled?

The transmission in your truck is controlled by the PCM (powertrain control module). It is sophisticated enough to be able to tell you if there is an issue with your transmission. The local auto supply may be able to scan it, but it may take a better scanner to dive deeper into the PCM.

What kind of ignition switch does a Chevy have?

Strattec/OEM #707835 + 706592 X2 + 598007 X2 CHEVROLET Factory Original Ignition Switch Lock Cylinder + 2 (Pair) Door Locks Cylinders + 2 OEM Chevrolet Bow-Tie Logo Key To Match ATTENTION: THIS SET FOR MODELS WITH AUTOMATIC TRANSMISSION ONLY.

How many keys are in a Chevy ignition?

Comes with a total of (4) keys, (2) are for the ignition switch and the other (2) are for the door locks. I don’t want to 2 different keys.

Do you have a Chevy bowtie on your keys?

These keys do not have a Chevy “bowtie” logo on them as described. They just have a generic “GM” emblem on them. The key ring hole is smaller than the original keys. The package was already open when I received it and did not include the door lock pawl retaining clips.

What to do if your ignition key won’t work?

In this case the ignition lock must be replaced. Step 7 – In extreme conditions such as high mileage or a key chain adorned with many ornaments can wear the tumbler which causes the key not to work. If the door key is same as the ignition key, the door tumbler can be removed and a key made if no security chip is installed, (older cars).

What causes a car key to not turn?

Examine the key for signs of excessive wear, rounding or broken teeth. Any of these could result in the key failing to turn in the ignition. If the key is damaged, it will have to be replaced.

What happens when you turn the ignition key in a Chevy Silverado?

Power the Accessories- This should be what you get when you turn the key to the first position. This allows you to use the power windows, radio, and any other accessory that is equipped in your Chevy Silverado.

Can a bad ignition switch cause a Chevy Silverado to stall?

Your Silverado stalls because the faulty switch turns off the fuel pump or power to the ignition. When this happens, the engine will not be able to run until it gets that signal back. 2. Starts then Dies If your Chevy Silverado is starting right up, but then immediately dies, that is a very good indication that the ignition switch is bad.

What to do if your ignition key won’t turn?

If that doesn’t work there is a little cable that goes from the shifter mech to the ignition switch. This is what makes the key impossible to turn off while in gear. Undo the side on the ignition switch. Maybe that will help. If not, make sure you have the park brake frimly engaged, then get under the truck.

Can a unworn key turn an ignition cylinder?

Or, an unworn key may not turn a worn ignition cylinder, as they haven’t “worn together.” How To Fix It: The best way to do this is to get a new lockset, with new keys and a new cylinder. You might consider getting a matched lockset that includes the door and trunk cylinders.

Can a bad ignition switch keep a Chevy Silverado from starting?

A bad ignition switch can cause your Silverado not to start at all. And, it can keep your Silverado from starting in a couple of different ways. The first is when the starter cranks, but the bad ignition switch doesn’t turn on the fuel pump or ignition.

How to reset the PassLock system on a 2000 Silverado?

If the Passlock system identifies the key as unauthorized, the engine stalls. Leave the ignition switch in the “Run” position as the “Security” light blinks on and off for approximately 10 minutes. Turn the ignition switch clockwise to start the engine immediately after the “Security” light stops flashing.

How do you replace the ignition switch on a Chevy?

Remove the two screws from the underside of the plastic steering column cover with a Torx screwdriver turned in a counterclockwise direction. Pull the cover straight down from the bottom of the steering column. Set the cover and screws aside. Locate the black plastic J-shaped lever on the ignition switch, revealed after removing the plastic cover.

Where is the ignition key on a Chevy truck?

Since most Chevy trucks now use a transponder key, a special ignition cylinder has to be made for your truck. Remove the screws on the underside of the steering column cover. Pull the cover down. Push the punch pin up into the access hole under the ignition cylinder. Pry the ignition lock out of the steering column with a flat tip screwdriver.

What does the ignition cylinder do on a Chevy truck?

The ignition cylinder on a Chevy Truck allows the ignition switch to activate and send an electrical signal to the starter motor. The motor then starts the engine. However, when the ignition cylinder jams, you won’t be able to start your truck.

How to remove the ignition switch without a key?

How to Remove the Ignition Switch Without a Key. 1 Step 1. Turn on your power drill and use your drill bit to make a hold in the key slot of the ignition cylinder. Be sure to make the hole large enough 2 Step 2. 3 Step 3.

Where is the release pin on an ignition switch?

The new or rebuilt switch should slide easily back into its hole on the steering column. Align the shape of the cylinder and the location of the release pin with the coinciding grooves in the ignition module.

How can I Fix my Chevy Silverado ignition?