Other

Can a bad throttle position sensor cause rough idling?

Can a bad throttle position sensor cause rough idling?

Faulty throttle position sensors can cause rough idling due to fluctuating airflow. If you see your car misfiring, idling rough, or stalling out while you drive, it is highly likely that you’re having a faulty throttle position sensor. Also due to fluctuating airflow, a bad throttle position sensor may cause all sorts of power issues.

Why does my IROC Z 305 Ping so much?

You will get some pinging due to no EGR flow, but if the idle or just off idle improves, the EGR is opening too fast due to carbon buildup inside the valve and must be replaced.

Is there a problem with my 1988 irocz?

I have an 88 irocz that had the same problem. Try unhooking your mass air sensor for a minute. your check engine light will come on but don’t worry about that. See if it runs any better like that. if it does then your mass air sensor is bad, If not check your throtle posistion sensor and make sure it is positioned right

What’s the voltage on my Torx throttle sensor?

My voltage was reading 4.39VDC so I loosened the top and bottom torx screws just enough to where I can move the sensor sort of clockwise and/or counter-clockwise to adjust and to where it won’t move on you when you let go to tighten the screws.

How big of a bore does a 305 TBI have?

The stock 305 and 350 TBI unit has 2 (1 11/16″) bores which flow 450 cfm of air. Up to 230hp engines that air flow is fine. you can do the ultimate TBI mods to the stock 42mm TBI unit and get that air flow up to 500cfm without increasing that bore diameter which is plenty for any 305 engine that you can run with TBI.

You will get some pinging due to no EGR flow, but if the idle or just off idle improves, the EGR is opening too fast due to carbon buildup inside the valve and must be replaced.

Can a IAT sensor be installed in a 305?

You can drill a hole in the base to put your IAT sensor in. Also toss the choke collar that is between the TBI and the air cleaner assembly. Good for around 5hp on a 305 car and again mandatory for any decent engine upgrade. Another nice setup can be seen here http://91rsramair.tripod.com/ for colder air input.

I have an 88 irocz that had the same problem. Try unhooking your mass air sensor for a minute. your check engine light will come on but don’t worry about that. See if it runs any better like that. if it does then your mass air sensor is bad, If not check your throtle posistion sensor and make sure it is positioned right

What happens when the throttle gets stuck in an open position?

When the throttle gets stuck in an open position than your vehicle will receive too much air and cause it to have a high or fluctuating idle. What are signs of a bad Throttle Position Sensor? Acceleration issues: A bad TPS may cause all sorts of power issues. Your engine may start up but it will have little to no power and it causes it to shut off.

What does it mean when your car Idles smooth?

Smooth idling indicates that your engine’s fuel and air are mixing just right. What is rough idling? If your vehicle’s idle is rough, possibly rising and falling, or having difficulty maintaining a steady rate of rotation, you may have a problem that needs fixing.

What causes a car to have a high idle?

If it stays shut then your engine is not going receive air and it won’t start. When the throttle gets stuck in an open position than your vehicle will receive too much air and cause it to have a high or fluctuating idle. What are signs of a bad Throttle Position Sensor?

Faulty throttle position sensors can cause rough idling due to fluctuating airflow. If you see your car misfiring, idling rough, or stalling out while you drive, it is highly likely that you’re having a faulty throttle position sensor. Also due to fluctuating airflow, a bad throttle position sensor may cause all sorts of power issues.

Why is there high idle after cleaning the throttle body?

The throttle position sensor (TPS) is often located on this body, however, and can be damaged when an untrained person attempts to clean it, resulting in a necessary recalibration after the fact–which can also be inconvenient and requires a trip to the mechanic or dealership. Why is there a high idle?

What causes a car to idle rough at idle?

A clogged fuel filter stops the engine from receiving the right amount of fuel causing the engine to be rough idle. Fuel filters are often pretty cheap, and you can easily get the fuel filter removed and replaced from a nearby mechanic or do it yourself if you have some knowledge. 6. Dirty Air Filter

What happens to the engine when left in idling position?

When the engine is left in idling position, it maintains a steady but low rate of revolution approximately 1,000 RPM. The RPM needle stays constant, and this indicates that the vehicle’s engine is receiving the correct amount of air and fuel.

What are the common problems with Ford Mondeo engines?

Solution: A common problem with this year TDCi engine is a bad connection for the fuel pressure sensor. To rectify the problem, a gold electrical connector should be used instead of the tin connector. Problem: Engine does not run properly or fails to start.

What causes dirt on inside of throttle body?

Dirt, grime, and carbon deposits on the inside of the housing. Similar to dirt and grime, carbon deposits can create an uneven surface inside the walls of the throttle body which can disrupt the atomization of the air/fuel mixture.

Are there any problems with Ford Mondeo 1.8 TDCi?

The early 1.8 TDCI Mondeos had problems with intermittent cutting out, uneven running etc. Ford released several ECU map updates to try and fix this, which seemed to work. Try searching the TalkFord forums in the Mondeo section, there should be plenty there. I seem to remember the ECU updates were coded for identification.

When the throttle gets stuck in an open position than your vehicle will receive too much air and cause it to have a high or fluctuating idle. What are signs of a bad Throttle Position Sensor? Acceleration issues: A bad TPS may cause all sorts of power issues. Your engine may start up but it will have little to no power and it causes it to shut off.

What’s the problem with the back of the Ford Mondeo?

Solution: The probable cause is sticking pads in the back plate asembly. The solution is to thoroughly clean the support area for the pads and fit new revised pads. Grease the pad supports with molycote silicone grease. Revised pads and extra grease have been used since 05/2002 for the Mondeo.

Author Image
Ruth Doyle