Most popular

Why is my Chevy Trailblazer key stuck in the ignition?

Why is my Chevy Trailblazer key stuck in the ignition?

All vehicles equipped with automatic transmissions have a lock that keeps the key from being removed from the ignition while the vehicle is in gear. This prevents your Trailblazer from “rolling off”. When the vehicle is in any other gear than park will act like neutral and roll away without the parking brake on.

What to do if your key gets stuck in the ignition?

Take the good key and duplicate it. Rusted – A key that is rusted can get stuck in the ignition system easily. It doesn’t have to be a lot of rust. Just enough to keep it from moving freely. As with a bent key, just start over. Once something rusts, it comes back a lot easier.

What causes a car key to not turn?

Examine the key for signs of excessive wear, rounding or broken teeth. Any of these could result in the key failing to turn in the ignition. If the key is damaged, it will have to be replaced.

What happens if you wiggle the ignition key?

Be careful not to apply too much pressure. Wiggling the key can make the key contact the pins from a different angle, which may allow you start the vehicle. If wiggling the key works, it means the teeth on the key are too worn to properly engage the pins. Replace the key as soon as possible if this works before the key stops working entirely.

https://www.youtube.com/watch?v=854qM7IshCY

Where can I find the owner’s manual for the Chevrolet TrailBlazer?

2021 chevrolet.com (U.S.) chevrolet.ca (Canada) Trailblazer Owner’s Manual 2021 Trailblazer Canada My Chevrolet App Download the my.Chevrolet App for full manuals and “how to” videos. The full owner’s manual is located with your vehicle infotainment system, if equipped.

What should I know about driving a trailblazer?

About Driving the Vehicle As with other vehicles of this type, failure to operate this vehicle correctly may result in loss of control or a crash. Be sure to read the driving guidelines in this manual in the section called “Driving and Operating” and specificallyDriver Behavior0181,Driving Environment0181, andVehicle Design0181.

All vehicles equipped with automatic transmissions have a lock that keeps the key from being removed from the ignition while the vehicle is in gear. This prevents your Trailblazer from “rolling off”. When the vehicle is in any other gear than park will act like neutral and roll away without the parking brake on.

What to do if your ignition key won’t turn?

This feature is not available right now. Please try again later. Sometimes the ignition key won’t turn or rotate. If that happens the vehicle won’t start, the steering wheel won’t turn and it won’t shift into gear. On a late 90’s or early 2000 GM vehicle this is the way to get it apart so you can replace the tumbler. Loading…

What to do if your ignition switch is stuck?

Step 1 – All vehicles have a steering wheel lockout safety device that will not allow the steering wheel to turn when the key is in the “OFF” position. Step 2 – Vehicles equipped with power steering utilize a pump which maintains pressure while the engine is running.

What causes the tumbler Assembly on a ignition switch to jam?

Step 4 – Dirt and debris inside the key lock can cause the tumbler assembly to stick and jam, not allowing one or more of the key followers to operate.

Can a car key get stuck in the ignition?

A key getting stuck in your Trailblazer’s ignition is not the most common problem. You can go the whole life of the vehicle and this typically won’t happen. Here are some of the most common reasons why the key would get stuck in the ignition. They are presented somewhat in the order of most likely to least likely to be the cause.

Why are the brakes locking up on my car?

The brakes are locking up When it is functioning correctly the ABS system is designed specifically to prevent the wheels from locking up during heavy braking, preventing loss of traction. However, there can be certain instances where a faulty ABS module can behave erratically, causing your brakes to lock up even under normal driving conditions.

A key getting stuck in your Trailblazer’s ignition is not the most common problem. You can go the whole life of the vehicle and this typically won’t happen. Here are some of the most common reasons why the key would get stuck in the ignition. They are presented somewhat in the order of most likely to least likely to be the cause.

Is there a way to bypass GM PassLock?

At NEWROCKIES Inc., we’ve designed our PRO Bypass Module with the specific purpose of bypassing faulty GM VATS, Passkey and Passlock security systems IN FULL.

What causes a misfire on a check engine light?

If you have a #2 misfire and move the #2 coil to #4, for example, then the misfire moves to #4, you know the coil is suspect. Defective fuel injector: If a fuel injector fails to deliver the proper amount of fuel to a cylinder, you will have a misfire.

What causes a car key to get stuck in the ignition?

In some cases, the ignition or vehicle isn’t the problem. It can be a worn or damaged key that has lodged itself in the ignition switch. Pulling or yanking on the key can cause major damage to the ignition and might make it even harder to remove the key.

What happens if you have an incorrect ignition code?

The chip in the key transmits a specific code, of which there are millions. If this code matches the ones programmed into the vehicle, engine starting is enabled. An incorrect key code, such as from an unprogrammed key or damaged key, would prevent engine starting. Code “confusion,” such as having multiple keys can also occur, preventing ignition.

Can a unworn key turn an ignition cylinder?

Or, an unworn key may not turn a worn ignition cylinder, as they haven’t “worn together.” How To Fix It: The best way to do this is to get a new lockset, with new keys and a new cylinder. You might consider getting a matched lockset that includes the door and trunk cylinders.

The chip in the key transmits a specific code, of which there are millions. If this code matches the ones programmed into the vehicle, engine starting is enabled. An incorrect key code, such as from an unprogrammed key or damaged key, would prevent engine starting. Code “confusion,” such as having multiple keys can also occur, preventing ignition.

Or, an unworn key may not turn a worn ignition cylinder, as they haven’t “worn together.” How To Fix It: The best way to do this is to get a new lockset, with new keys and a new cylinder. You might consider getting a matched lockset that includes the door and trunk cylinders.

Why does my Gm key not turn in?

The GM (Buick, Cadillac, Chevy, GMC, Hummer, Oldsmobile, Pontiac) ignitions tend to fail because of wear from inserting the key at a slight angle. This is the same for the Chrysler vehicles (Chrysler, Dodge, Eagle, Jeep, Plymouth).

How to program Chevy Gm key with no keys programmed?

The programming of any of these Gm keys is relatively easy and most of them can be programmed yourself DIY. If you have at least 1 working key…. If all keys are lost…. Then you must perform what we call the 10x10x10 procedure: Insert new key and turn on (do not start!)

Why does my car not start when I Turn on the key?

This feature is not available right now. Please try again later. One possible reason your car wont start is a bad connection. This is one of those things that is often over looked until after the battery or starter or alternator have been replaced or all of the above. if this happens to you check your battery connections. Loading…

What causes a locked steering wheel to not turn in?

If a locked steering wheel is the only thing preventing your key from turning the ignition, then follow our instructions below for How to Unlock a Locked Steering wheel and you will be back on the road fast. Problem 2. Dirt, pocket lint or debris (like tape from opening a package) may cause your key not to turn in your ignition lock cylinder.

What to do if your Trailblazer won’t move?

Dorman makes the replacement, pretty cheap. 27 people found this helpful. KenF and FJ4072 thank you but KenF it’s a automatic transmission 2002 trailblazer Lt 4wd it starts fine but when I put it in reverse or drive it doesn’t move just revs and on the dash it’s saying it’s going to the gears I’m choosing but neither gear moves the truck

This feature is not available right now. Please try again later. One possible reason your car wont start is a bad connection. This is one of those things that is often over looked until after the battery or starter or alternator have been replaced or all of the above. if this happens to you check your battery connections. Loading…

If a locked steering wheel is the only thing preventing your key from turning the ignition, then follow our instructions below for How to Unlock a Locked Steering wheel and you will be back on the road fast. Problem 2. Dirt, pocket lint or debris (like tape from opening a package) may cause your key not to turn in your ignition lock cylinder.

Take the good key and duplicate it. Rusted – A key that is rusted can get stuck in the ignition system easily. It doesn’t have to be a lot of rust. Just enough to keep it from moving freely. As with a bent key, just start over. Once something rusts, it comes back a lot easier.

Author Image
Ruth Doyle