Most popular

Why does the fuse keep blowing on my power seat?

Why does the fuse keep blowing on my power seat?

Replaced fuse and seat worked just long enough to move it so I could at least fit in to drive, but then blew again. Bought some fuses and replaced it again. This time it was blown before I could even move the seat at all (key not in, seat normally works with out key). Had lots of fuses so tried another. Blown. Bleh.

Can a blown fuse be switched back on?

The breakers reset and can be “switched back on”–so there is no need to replace anything. Much of the time, it’s technically inaccurate to refer to a “blown fuse,” so in this article, we’ll offer you some new concepts and vocabulary to describe your various electrical concerns.

How often do you get a blown fuse?

Most people probably have experienced a blown fuse at one time or another. Someone always knows what to do when this happens. If you’re a homeowner, that person probably is you. Blown fuses are a common occurrence.

What causes a circuit breaker to blow a fuse?

Any faulty wiring or connected parts risk a power fault (surge), which trips a circuit (or blows a fuse). So, again, the problem is not that the circuit breaker (or fuse) didn’t do its job but rather that there was faulty equipment.

What causes a car battery to drain while driving?

Faulty Charging. If your charging system isn’t working properly, your car battery can drain even while you’re driving. Many cars power their lights, radio, and other systems from the alternator, which can make the battery drain worse if there’s a charging problem.

Is the Mercedes Batterie seat control module recalled?

This is ridiculous (fraudulent) considering the frequency and number of reports that these Seat Control Modules haven’t been recalled and batterie charged or replaced at Mercedes Benz expense. I have to jump start it every morning. For some reason at night the battery is drained.

How can I stop the drain on my seat?

I had the same problem. unplugged both seat modules to stop the drain. A free fix is to take the 12v power line (red wire)at the module plug under seat and cut it and tape off lead coming from harness . Then solder a jumper from the switched power source (ignition)to the cut lead going to multi plug to module.

What to do if your power seat is not working?

Turn your ignition to ON, but leave the engine turned off. Try to move the power seat that is not working and listen for the seat’s motor. If the motor is quiet, lift the switch. It will be on either the door handle or the seat’s side. Use your test light to see if there is any voltage at the switch.

How to diagnose a Chevy power seat motor issue?

If no voltage is indicated, then check the wiring to determine whether or not there is a short somewhere between the fuse panel and the switch. Check for continuity by unplugging the switch and using the multimeter. Should you find there is no continuity, then replace the switch. If there is a relay between the switch and the motor, test it.

What can cause a power seat to overheat?

Even if a soda is spilled in the vehicle it is possible for the track to become sticky enough to overheat the power seat motor. If the power seat was fine in some directions and will not move in other directions from a particular control that switch should be removed and tested.

How do you remove a power seat switch?

In removing the switch of a power seat, be guided by the following: ​Step 1. Disconnect the power seat’s negative battery cable. Carefully do it and after you’ve done it, set it aside. Step 2. Remove the trim panel of the seat. In doing this, you will need screwdriversfor moving out screws.

Where are the power seats on a Chrysler?

This will be located on the inboard side or the seat belt buckle side. Screw in your new drive block screw and torque it to 28 Nm or 250 foot pounds. Put the seat back in its place.

Why does my power seat move when I stop?

Drivers are often left with a rocking motion when they stop and go. Follow these tips to learn how to diagnose this problem and fix it. Note that your power seat seems to move in and out of place as you break or accelerate your car.

How to fix a loose power seat adjuster?

This indicates that your power seat adjuster is loose. Get a drive block screw for your car’s power seat by ordering Part Number 05080982AA, a T-50 Torx Bit and a torque wrench. Hoist the vehicle. Disconnect and isolate the negative battery cable underneath the hood.

This will be located on the inboard side or the seat belt buckle side. Screw in your new drive block screw and torque it to 28 Nm or 250 foot pounds. Put the seat back in its place.

Why is my power seat not moving forward?

A seat may be jammed if it cannot freely move in the forward or backward direction, but can only move in one direction, or simply works inconsistently. Your first step is to find out if your seat’s other components are working, by confirming that the fuse, the relay switch, and the circuit breaker are in good condition.

What are the different types of power seats?

Power seats come in two broad categories; the four-way and the six-way power seat.

What happens to the power seat when the battery dies?

The ECU has its own battery that stores the seat position memory and other various components such as mirrors. When the ECU battery dies, moving the car power seat may be stuck in one position or you may exhibit unexpected results such as the mirror button moving the seats and the seat button moving the mirrors.

Why is my cruise control not turning on?

If the brake pedal switch fails, the car may think the brakes are engaged and not allow the cruise control system to turn on. Failing Speed Sensor: A speed sensor has many purposes including indicating the speed of the vehicle, regulating flow of fuel and ignition timing, and operating the cruise control.

How to remove and replace the cruise control switch?

1- Remove the T-30 Two screws from the right and left side of Steering wheel to remove the airbag. 2- Move Airbag to the left side carefully to get to the two screws holding the Cruise Control Switch on the steering wheel. 5- Remove Cruise Control switch by sliding it to the left slowly and pulling it out at the same time. Loading…

What to do if your fuse keeps blowing?

1. Both POS & NEG cables CONNECTED to battery. Test for continuity on any device’s two contact points (e.G. Disconnect cigarette lighter socket and test connector plug, or remove light bulb and test contact points). 2. POS cabled DISCONNECTED, NEG cable CONNECTED.

Replaced fuse and seat worked just long enough to move it so I could at least fit in to drive, but then blew again. Bought some fuses and replaced it again. This time it was blown before I could even move the seat at all (key not in, seat normally works with out key). Had lots of fuses so tried another. Blown. Bleh.

What to do if your power seat does not move?

The seat may not move forward or backwards, or in any of the directions it is meant to move. If the seat is not moving at all, check the fuses to see if they have blown. If the fuses are still intact, contact a professional mechanic to replace your power seat switch so you can be seated in the proper driving position.

When do you Know Your power seat switch is failing?

If you notice your seat is moving slowly, stops moving, or does not move at all, your power seat switch may be failing. 1. Seat does not move 2. Seat moving slowly 3. Seat stops moving while pressing the switch The power seat switch comes in most modern vehicles.

1. Both POS & NEG cables CONNECTED to battery. Test for continuity on any device’s two contact points (e.G. Disconnect cigarette lighter socket and test connector plug, or remove light bulb and test contact points). 2. POS cabled DISCONNECTED, NEG cable CONNECTED.

Why does my Chevy power seat not work?

If you have two power seats, and they both are not working, it may be a fuse or circuit breaker. If one seat works and the other does not, it is probably not the fuse. Turn your ignition to ON, but leave the engine turned off.

What are the major issues with power seats?

Major power seat issues 1 Wire harness under the seat (which you’ve done.) and fuses. 2 Seat switch on the side of the seat. 3 Seat motor under the seat.

Why is my NOx power seat not working?

If your Nox had power forward/backward before then you need to look at your fuses and hopefully you will have a blown fuse. My power drivers seat won’t work anymore. My husband moved the seat to fit him and now I can’t move the seat up and forward for me.

Are there any problems with the Ford Edge?

280-horsepower 3.5L V6 6-speed shiftable automatic AWD Air conditioned driver’s seat does not cool. Driver’s seat parts had to be ordered not in as yet. Rear gate doesn’t open with foot. Tail gate repaired. New part and reprogrammed key fob. Blis Blind System kept activating for no reason. Could not detect problem.

Why is the driver’s seat not cool in my Ford Edge?

Air conditioned driver’s seat does not cool. Driver’s seat parts had to be ordered not in as yet. Rear gate doesn’t open with foot. Tail gate repaired. New part and reprogrammed key fob. Blis Blind System kept activating for no reason. Could not detect problem. Driver’s seat does not return to full position for exiting the car.

Why did my power seat on my car stop working?

On the 16th minute, my driver’s side power-seat return stopped working. I jiggled the switch in disbelief, accidentally reclining it so far that even with both arms at full stretch I struggled to reach the wheel.

What should I do about my Ford Edge power seat?

Check the harness into the seat back motor and checked the main harness under the seat. All is fine. Checked fuse #23 in the main fuse box (drive seat control) and not blown. I have read a lot on the forums about this, but can’t seem to narrow it down to the edge. Any thoughts anyone? 23 people found this helpful.

Why is the seat back on my Ford Edge stuck?

The seat back was stuck all the way laying back and won’t come up. Check the harness into the seat back motor and checked the main harness under the seat. All is fine. Checked fuse #23 in the main fuse box (drive seat control) and not blown.

How does the passenger side of a Ford Edge work?

Passenger side work,s there is fire,it run,s both of them. 9 people found this helpful. It’s not the plug, it’s the seat track, and extremely expensive to fix. Ford will not recognize the problem and help pay for the damage. We can’t move the seat forward and now the seat is leaning backwards, so if someone hit you, you could break your neck!

280-horsepower 3.5L V6 6-speed shiftable automatic AWD Air conditioned driver’s seat does not cool. Driver’s seat parts had to be ordered not in as yet. Rear gate doesn’t open with foot. Tail gate repaired. New part and reprogrammed key fob. Blis Blind System kept activating for no reason. Could not detect problem.

A seat may be jammed if it cannot freely move in the forward or backward direction, but can only move in one direction, or simply works inconsistently. Your first step is to find out if your seat’s other components are working, by confirming that the fuse, the relay switch, and the circuit breaker are in good condition.

Is there a way to repair a power seat?

Repairing car power seat problems can sometimes be as simple as removing a penny from the seat track. Or they can be as complicated as having to test switches, relays and motors. Most power seats are not protected by a fuse but instead use a circuit breaker.

What to look for when troubleshooting a power seat?

The trick when diagnosing car power seats is to focus on the mechanical or electrical problem areas: the mechanism that fails to lower and raise the seat, or the part that slides or tilts the seat forward and backwards. Keep this in mind as you troubleshoot your power seat, whether it comes with one, two or three motors.

Why is my electric seat not working in my Mercedes?

If its is CLK320 2002, then is it the fuse no 6. white 25 fuse. Otherwise please check the list in the fuse box, it will tell you which one is for seat adjustment. yep my passenger seat has the same problem. i can still hear a clicking sound when i press the backward and forward button though…. like its stuck…

Click to expand… WKJeeps.com has a good page about fuses.The owners manual sucks when you try to find fuse related stuff. dumb question but does it sound like it is trying to adjust seat or no noise what-so-ever when you mess with it?

What’s the fuse for the electric seat adjustment?

Click to expand… so which fuse was it….in the trunk or somewhere else? If its is CLK320 2002, then is it the fuse no 6. white 25 fuse. Otherwise please check the list in the fuse box, it will tell you which one is for seat adjustment.

Why does the driver’s side headlight keep burning out?

High beams and running lights are fine. Replaced the driver’s side headlight and the regular light keeps burning out. High beams and running light are fine. Passenger’s side works fine.

What should I do if my headlight keeps blowing out?

During the installation process, always ensure that the electrical connectors that emanate from the power source have been well joined within the metal connectors to the headlight bulbs, the alternator on the other hand should be monitored to ensure there is no overcharging of the battery.

High beams and running lights are fine. Replaced the driver’s side headlight and the regular light keeps burning out. High beams and running light are fine. Passenger’s side works fine.

During the installation process, always ensure that the electrical connectors that emanate from the power source have been well joined within the metal connectors to the headlight bulbs, the alternator on the other hand should be monitored to ensure there is no overcharging of the battery.

Why does the fuse keep blowing on my air compressor?

If the air suspension compressor is kept engaged for too long, it can get damaged. There is the chance of a blown fuse for the air compressor pump. You can replace the fuse with a new one but if it keeps on blowing you have another issue, usually pointing at the air compressor pump / motor.

Where do you find the fuse on a wiring diagram?

Wiring diagrams or schematics differ between manufacturers. Some diagrams will provide a chart showing each fuse circuit down the left hand side, with each system circuit across the top. Find the fuse that keeps blowing and move across the page from left to right noting each system circuit that you come across.

How can I tell if my Fuse has blown?

If the thin metal strip has separated, then the fuse has blown. Another way to accurately identify a blown fuse is to use a fuse tester, which costs between $5 to $10 and usually comes with replacement fuses as well. A fuse tester will fit in your glove box, and some types also have an attached fuse puller.

Where is the fuse box on a car?

You can find the instrument panel fuse box under the dashboard of the driver’s side. The lid can easily be removed by pulling it down. Most interior fuse boxes come complete with a plastic fuse puller. If yours is missing, you can use tweezers or needle nose pliers to remove the fuses.

What do you need to know about Chevy Silverado fuse box?

Knowing your way around your truck’s fuse box (es) can mean the difference between resolving a minor electrical issue yourself, or paying a professional a hefty sum to do it. Here’s what you need to know about your Chevy Silverado. This article applies to the Chevrolet Silverado GMT800 (1999-2006).

How is the amperage of a fuse determined?

Generally, the bigger the fuse, the higher its amperage (A)—the flow of current supplying a component with its required amount of power. As the color of a fuse can also help you identify its amperage, the number is usually labeled on the fuse itself.

Where is the circuit breaker on a power seat?

If this is not the case the next thing to check is the circuit breaker. This is usually located in the main fuse panel. Circuit breakers are easy to test with an inexpensive automotive meter. The circuit breaker when removed should be in the closed position and you can do a simple continuity test to confirm that it flows current.

Why is my child’s power seat not working?

Often when I find power seat problems where it is not working in any direction at all, I find in many cases that the power harness or wiring has become disconnected. Although this wiring is tucked away sometimes passengers or children can accidentally dislodge it and inadvertently disconnect the connector.

Where is the fuse on a power seat?

Although this wiring is tucked away sometimes passengers or children can accidentally dislodge it and inadvertently disconnect the connector. If this is not the case the next thing to check is the circuit breaker. This is usually located in the main fuse panel. Circuit breakers are easy to test with an inexpensive automotive meter.

Repairing car power seat problems can sometimes be as simple as removing a penny from the seat track. Or they can be as complicated as having to test switches, relays and motors. Most power seats are not protected by a fuse but instead use a circuit breaker.

Often when I find power seat problems where it is not working in any direction at all, I find in many cases that the power harness or wiring has become disconnected. Although this wiring is tucked away sometimes passengers or children can accidentally dislodge it and inadvertently disconnect the connector.

If this is not the case the next thing to check is the circuit breaker. This is usually located in the main fuse panel. Circuit breakers are easy to test with an inexpensive automotive meter. The circuit breaker when removed should be in the closed position and you can do a simple continuity test to confirm that it flows current.

Even if a soda is spilled in the vehicle it is possible for the track to become sticky enough to overheat the power seat motor. If the power seat was fine in some directions and will not move in other directions from a particular control that switch should be removed and tested.

Where are the fuses on a Hummer H3?

Fuse box diagram (fuse layout), location, and assignment of fuses and relays Hummer H3 / H3T (2005, 2006, 2007, 2008, 2009, 2010). The wiring circuits in your vehicle are protected from short circuits by a combination of fuses and circuit breakers. This greatly reduces the chance of fires caused by electrical problems.

What causes the wiper to stop on a Hummer H3?

If the motor overheats due to heavy snow or ice, the wiper will stop until the motor cools. If the overload is caused by some electrical problem, be sure to get it fixed. Circuit breakers protect the power windows and other power accessories.

Author Image
Ruth Doyle