Why does my GMC engine start but not run?

Repair guides and support for cars, trucks, and SUVs manufactured by GMC. Answered! View the answer I have this problem too Is this a good question? An engine will start but not run when the fuel runs out .

Why does my GMC Truck idle rough in the morning?

So the past couple months I’ve noticed my truck has a really rough idle in the mornings when it is cold out, to the point where it has even died before. I just replaced the plugs about 3 months back and it ran fine after, people have told me things like it is the o2 sensors to the cat is plugged up to my fuel filter is bad.

Why does my GM Truck start then die?

He was thinking fuel pump or fuel filter. He was about to take it to a dealer to be checked out when someone told him to turn the key to the on position and leave it there until the dash lights went out then start the truck. He did this and says the truck is running fine now. It reset the security system.

Why does my GMC truck run too lean?

The scanner reads that bank 1 and bank 2 are too lean and some misfires. The running too lean code could be due to the K&N intake I have. A guy told me it may be my fuel pump, but that is a $272 guess that I am not about to make.

What to do if your GMC Sierra won’t start?

Attempt to start the engine. If it doesn’t start then release the key back to the on position. Watch the security light. After 10 to 15 minutes the security light should turn off. Turn the ignition off and wait 5 seconds. Repeat steps 1 through 4 two more times for a total of 3 cycles (30 minutes).

Can a Silverado Sierra GMC start then dies?

I’ve got another 99 6.0L that i’ve swapped the MAF, MAP, Idle Air, Throttle Position sensor, both computers, all relays, nothing changes the behavior. I’ve checked all the fuses i can find that would be releated to engine function, on both fues panels.

Why does my GMC Savana Van not start?

Lately I have had this problem: Go to start the van and if fires up for about one second then quits. Try and try it will not start. Dealer at first said it was the fuel pump. Replaced it. Months later still doing the same thing.

Why is my starter motor not cranking up?

In this case, no power is flowing through the neutral safety switch to the starter relay. This prevents the starter motor from cranking the engine. This symptom indicates a completely open electrical circuit inside the neutral safety switch which may be due to a faulty relay, blown fuse, or electrical problem with the switch itself.

What do you need to know about engine will not start?

All engines require three things to start and run; spark, fuel and compression. So, if any one of these is missing, your engine will not start. With a engine will not start issue, the possible causes are plenty; so it’s important to understand, what it takes to make a engine start and run.

How to troubleshoot a no start GM 4.3L pick up?

Testing a Cranks but Does Not Start condition on your GM 4.3L, 5.0L, 5.7L pick up, van or SUV is not that hard to do, if you have a solid diagnostic strategy. In this article I’ll show you the basics of testing such a problem.

When did my GMC Sierra air conditioner stop working?

I had a 2001 GMC Sierra that did this when truck was less the one year old (summer of 2001 is when it was). The dealer had the truck in the shop idling for a long time and the A/C worked perfectly. I told them to take it for a ride and see. So the service manager in an effort to convince me nothing was wrong went for a ride with me driving.

What to do when your GMC Sierra stops running?

If you have fuel pressure after the above tests pull a spark plug and check for spark. If you don’t have spark check the cam position sensor in the distributor. If you have spark with no pressure it is the pump.

What should I do if my Duramax won’t start?

Very slight. Drove 5 miles, had dinner, came out, crank but no start. Held throttle down and still no start. Checked prime, fuel squirted out of vent when loosened. Cranked and held throttle down, started after about 10 seconds.

Why does my 1988 Chevy Silverado not start?

I’ve got a 1988 K1500 with the 350 FI. It won’t start, turns over, but won’t start sounds like fuel problem. Fuel pump has been changed, fuel filter, Fuel pump relay, Fuel pump fuse, ignition coil, all have been changed or checked. Any ideas. It is getting power, just seems to not be getting any fuel. The possibilities are endless.

What does it mean when your truck won’t start?

So your truck won’t start because it doesn’t have enough power to fully energize the electromagnet inside the starter solenoid. The magnetic field keeps on failing, so the solenoid spring keeps on snapping back. That’s what is making the click-click-click noise you hear.

What’s the problem with my GMC Sierra truck?

When I turn the key it cranks for about 1/4 second then nothing . None of the gauges or power locks and windows work . The battery is fine . Last night while driving all the gauges quit working and the a/c compressor kicked off , but the truck still ran fine .

Why is my Chevy Silverado 1500 not starting?

However, today, when the truck will crank and start, the antitheft icon goes off after a few seconds with the key on and stays off while the truck is running. It never flashed either today or yesterday though. And I don’t know if the antitheft system disables cranking or starting or both.

What should I do if my truck won’t start?

go back to the basics.what are the basics you say you said you got spark number one. check all your fuses in the cab.in the fuse box in the engine.

What kind of truck won’t start or fire?

I have a 1997 Chevy Z71 just put new trans in drove for about 20 miles and the truck just died………Replaced fuel pump, Fuel relay and found that the fuel fuzz blows every time I turn key on ???? 24 people found this helpful. 22 people found this helpful.

What to do if your truck wont start?

To avoid throwing guesses and parts at your truck, have the truck scanned for trouble codes as a first step. Some of the auto parts suppliers offer free code reading like Pepboys, Nappa, Advanced auto parts,etc and some of the guys are very knowledgeable and may have seen the issue often and put you on the right track.

What kind of car stalls after engine heats up?

The Chevrolet Cavalier is a compact automobile produced from 1982 to 2005 by General Motors. car starts and runs fine until engine heats up to operating tempature, then it stalls, it will restart but keeps stalling until engine cools down. What can cause this? Answered!

How to start a new Chevy truck question?

Start a new Chevrolet question. Content submitted by Users is not endorsed by CarGurus, does not express the opinions of CarGurus, and should not be considered reviewed, screened, or approved by CarGurus. Please refer to CarGurus Terms of Use.

Why does my truck run bad when it is really warm?

If it is telling the ECM that your engine is cold but it is really warm, it can cause it to run poorly. Usually, if the ECT sensor was bad, the truck would restart after the engine cooled down. I wonder if the cat is plugged. You should remove the 02 sensor from the exhaust manifold and try to start it.

Why does my car not start after warm?

Car will sometimes not start after warm. When i start my car, for the first time during the day- I have no problem. When I go somewhere and shut it off, sometimes it won’t resatrt. It doesn’t seem to matter what the weather is outside, it just does it when it feels like it.

Why does my Silverado 1500 engine not start?

Restarting the engine from this state may be difficult. The fuel can vaporise due to being heated by the engine, by the local climate or due to a lower boiling point at high altitude. A vapor lock is more likely to develop when the vehicle is in traffic because the under-hood temperature tends to rise.

What to do if your truck won’t start?

Fuel pump is running it’s little heart out, starter is trying its hardest, but the truck just will not fire up till it damn well feels like it. I’ve already replaced both the cam and crank sensors, new fuel pump and filter as of 3 months ago, and new wires and plugs as of 2 months ago.

Why does my car not start when I turn the key?

This condition is usually due a failed fuel pump, a failed ignition coil, a failed ignition control module, a failed crank sensor, etc… that lets the engine crank (turn over) but does not let it start. A No Crank Condition means that the engine is not turning over when you turn the key to crank the engine.

What to do if your engine keeps running after you turn off the ignition?

If your engine keeps running after turning off the ignition key, try to troubleshoot and repair the fault as soon as possible. Dieseling can cause serious engine damage if the problem worsens. Check the different systems and components as outlined above.

Why does my car not turn off when I Turn Off the engine?

Dieseling is rarely a problem with fuel injection because the fuel delivery is shut down as soon as the switch is off. Unless it is specially equipped, a carburetor will deliver fuel as long as there is air passing through it. If you have a fuel injected car that is dieseling, there is a leaking fuel injector in the system that has to be replaced.

What happens if you turn off the engine without the key?

Caddiac Thanks..Yeah the engine is still running without the key in it and it either shut off after 5 to 15 seconds or more or it slowly starts to shake till it dies out on its own.

Why does my car run when the ignition is turned off?

With the ignition turned off and the car continuing to run, simply remove the plug from the alternator (DO NOT TRY AND REMOVE THE BATTERY POWER WIRE FROM THE POWER STUD!) and the car should shut off if the alternator is creating the problem. If it does not stop running, your feedback problem is coming from something other that the alternator.

Why is my Silverado running without the ignition switch?

Open the door, and all RP voltage, included this backfeed, is removed. You need the find the component that is “leaking” this RP voltage. It could be the ignition switch. It could be a couple of wires shorted together (where, I don’t know).

Why does my Silverado keep running without the key?

SILVERADO3 ill take a look i really dont like to mess wit the truck being that that seem to be like an electrical problem dont want to mess anything up more than what already is but doesnt hurt to try thanks ill let you know what i come up with.

Why is my Chevy Vortec 4300 V6 leaking fuel?

In the L35 and LF6 engines, the spider injectors are known to leak at the pressure regulator and at the supply and return lines due to a design fault. Outside of leaking fuel onto the exterior of the engine itself, it can cause excess fuel to get sucked into the engine.

Is there a problem with the Chevy Vortec engine?

3L [&Vortec&] engine, the LU3, which was manufactured from 2003-2014 has been known to [&consume&] excessive amounts of [&oil&]. Owners [&have&] reported the car requiring [&two&] quarts or more of [&oil&] in between normal [&oil&] changes. The excessive [&oil&] [&consumption&] is likely to be caused by the Active Fuel Management system.

What causes a car to run lean at idle?

If the root cause is an electrical problem within the idle air control valve itself, you will likely have to replace the IAC. A vacuum leak is a hole in a vehicle’s air intake system behind the mass air flow (MAF) sensor that allows unmetered air into the engine. This throws off the expected air fuel ratio and causes the vehicle to run lean.

What causes a car to start and then die?

But if there is a fuel leak somewhere, then the proper amount of fuel won’t be able to make it to the combustion chamber. This might cause the engine to still start, but it won’t be able to keep it running. That is why it will die almost immediately after it starts.

Why does my car run after I start it up?

One potential problem that could arise is the inability to control the fuel injection system correctly. This might cause problems keeping the car running after you start it up.

Why does my car shut down when I Turn Off the key?

If this is happening to your car, it’s probably an old one with carburetors. New models all use electronic fuel injection, which shuts down when the key is switched off. Without fuel going to the cylinders, there can be no running on.

Why does the engine stay running with the key out?

Switch key to the off position and pull out, radio and stuff stays on as normal until door opens then shuts off. Every once in a while the engine will stay running along with all the other RAP features. It’s not normal. Sounds like you have a faulty ignition switch. I’d get it looked at under warranty…since you have a 2013.

What should I do if my car keeps running when I shut it off?

A running-on car is not only a waste of energy and fuel, it also presents a potentially dangerous situation. Book a mechanic to diagnose the issue as soon as possible. Fast and easy Car stays running when I shut the key off Inspection service at your home or office.

Why does my car keep running after I Turn Off the ignition?

It now has 42,000 miles on it, and several issues have been fixed with no recurence. However, the other night, I returned home from the store and noticed that the engine kept running after I turned off the ignition and removed the key. It sputtered for a little while and then quit. I didn’t think it was a big deal, and turned in for the night.

What should I do if my Silverado engine dies?

Update as of today: 1) the truck hasn’t started and kept running since last week. It only starts right up, then dies immediately. 2) I got a fuel pressure tester and the pressure is at 53 with key on, and maintains pressure when it starts (then dies).

What happens when a GMC Silverado shuts off?

Usually if it is bad the truck stays on but won’t start after it gets warmed up so that is probably out of the question. GM’s Passlock/VATS anti-theft system does not let it run for 5-10 seconds; it starts and immediately stalls.

How long does a GMC Silverado run before it stalls?

GM’s Passlock/VATS anti-theft system does not let it run for 5-10 seconds; it starts and immediately stalls. It works the same on new and old GMs alike.

Why does my Chevy Truck start and idle?

Not sure why this test caused a better and longer gas flow than the above test of just putting the ignition in the ON position and seeing how much gas comes out of the line before the fuel filter. Last test says to start the vehicle and remove the relay.

Can a Chevy Truck turn over but not start?

I replaced the starter, have checked the battery and even jump acrossed the starter, which did make it turn over but not start, but I cannot get the truck to turn over with the ignition switch. Is there any way to test the switch? When I turn it to the on position everything seems to work. When I try to start it nothing works.

Why does my car not start when I start it?

There are three very basic components that the engine, in your GM vehicle, needs to start and they are: Air, Fuel and Spark. When your 4.3L, 5.0L or 5.7L GM vehicle cranks but does not start…it’s because one of these components is missing from the mix.

Why does my GM 4.3L engine not start?

No Start Condition Basics There are three very basic components that the engine, in your GM vehicle, needs to start and they are: Air, Fuel and Spark. When your 4.3L, 5.0L or 5.7L GM vehicle cranks but does not start, it’s because one of these components is missing from the mix.

What to do if your C-1500 wont turn over?

I had a similar problem with my C-1500 and it was dirty terminals. Take them apart and cleam them with baking soda and water, there is a sleeve in one of them that will come out with some persuasion, clean them well and cover them with dielectric grease and reassemble. see if this helps. Make sure you tighten but not over tighten the terminal.

What to do if your GMC Sierra 1500 wont start?

If you discover white deposits or silvery-green deposits, but no further cracks or damage, you do not have to replace the battery, just clean it. To clean the battery on your GMC Sierra 1500, you have to remove the pole cables first, which requires no special knowledge, just a little concentration, as the order is very important.

What does it mean when your car says no start?

A No Crank Condition means that the engine is not turning over when you turn the key to crank the engine. The most common problem, that causes this condition is a failed starter motor. If your vehicle is suffering a No Crank Condition, this tutorial may be a good starting point: How To Test The Starter Motor (GM 4.3L, 5.0L, 5.7L).

What to do when your GMC Truck won’t start?

Try turning your key to the run position a few times (with out starting). Then try to start it. If it starts, sounds like what mine did. I replaced the fuel pump assembly and that fixed the problems. Very common problem.

What kind of Chevy truck won’t start?

In this video we encounter a condition where a 2002 Chevy Silverado ( Similar to GMC Sierra ) pickup has a symptom of the engine cranks over but won’t start…. In this video we encounter a condition where a 2002 Chevy Silverado ( Similar to GMC Sierra ) pickup has a symptom of the engine cranks over but won’t start….

Why does my 1988 GMC Sierra 1500 not start?

I’m having the same problem with my 1988 GMC 1500 I was told its the starter I’m going to replace it I guess that will determine if its the starter ornot just wwish I had a for sure wayof knowing 37 people found this helpful. Having same issue. Changed out starter two days ago. Still is a hard start. Sometimes I need starter fluid

Why does my GM Truck start and die?

Starts and runs fine and then all of the sudden. Yesterday morning it starts and dies after about 1 second, started it again and same results. It does this several times. After about 30 mins of trying and talking to it a while it started and ran fine. Drove over to the garage turned it off and restarted several times and it was fine.

What causes a 6.5L diesel engine to stall?

SYMPTOM: Your 6.5L Diesel stalls just as if someone had reached over and turned off the ignition switch. CAUSE: There are two main causes. The first and most common is the PMD (also called FSD).

What to do if your GM pick up has no start?

One of the most overlooked areas, when testing a hard to diagnose no-start, is the mechanical condition of your 4.3L, 5.0L, 5.7L GM pick up, van or SUV. Checking the engine mechanical condition means an engine compression test.

What kind of truck has no cel on?

One of my work trucks is 06 c5500 8.1L vortec its not showing any codes or no CEL is on and it starts and idles fine.

Why does my GMC Sierra 1500 stall at high RPM?

At higher rpm seem almost like the exhaust is clogged but the cat has been bored, itll rev up but just wont really go. Today experienced a poping sound almost like a backfire from underneath. After the truck starts and is warm at a stable idle in park/neutral it’ll rev up fine.

What does rough idle mean on a GMC Sierra?

rough idle, stalling, loss of power. o2 sensor code 44 (lean) Replaced: coolant temp sensor, tps, map sensor, fuel filter, and o2 sensor. It will run normal on occasion but only lasts about 45 seconds or so.

What happens when the diaphragm is ruptured on a GMC Sierra?

If the diaphragm has ruptured it will literally be like putting a hose with fuel into the intake and running it full. When it initially started to go it probably slowly flooded the engine to where it seemed to run ok but the excess fuel created a ton of carbon coating the O2 sensor. Since no air could pass through it, it gave a false lean reading.

Why is my GMC Sierra 1500 stalling and dying?

There is no code given. Have changed the injectors, timing, fuel tank, fuel pump, fuel pump, map sensor, cooling temp sensor on front of block, rebuilt the tbi, air idea valve. None of this hasite helped. The truck starts and dies. Have to give a little gas to keep running. While driving have to 2 foot it so it won’t die.

Why does my car stall out when in gear?

I was told it was the cadiladic converter but that was not the issue. Once it is in gear It will not stay running unless you use the 2 foot method and it is very rough and wont run for more than a minute. It never did this untill I got it back from the collision center after I was hit in the front passenger side?

What causes a Chevy 6.0 Vortec engine to leak?

They are subject to extremely high heat temperatures which can cause gaskets and bolts to warp and go bad, creating an exhaust leak. On the Chevy 6.0 vortec engine, the exhaust leak is most commonly caused by the exhaust manifold bolts completely breaking off. When the bolts break off, air gaps will open up causing exhaust gasses to escape.

Why does my GMC Sierra 1500 stall while in gear?

Motor wants to stall while in gear (but doesn’t do it out of gear once over 1000 rpm it dosent) seem to stall and it is only from a dead stop. Fuel filter has been replaced and TBI was rebuilt last April but it sort of used to do something like this when it was like 40 degrees or below. Could be torque converter lockup solenoid in the trans.

What is the diagnostic code for engine stall?

Diagnostic trouble codes P0120, P0121, P0122, P0123, and P0124 are what will commonly appear. The engine can stall for no reason and without any warning. This happens when the TPS gives incorrect information to the ECM. The engine can stall at high speed, at low speed, or even at idle.

Why does my car stall at low rpm?

The will likely force your computer to stall the engine and only allow it to run at low RPMs, which means the car will only move at slow speeds. This is a safety feature enforced by the computer so that your engine doesn’t get too damaged.

What causes idle surges on a car ECM?

Idle surging can be caused due to other issues in the car, but if it happens in conjunction with other throttle position sensor symptoms, the culprit is often the TPS. At idle, the ECM will not get the correct information and the throttle will variate randomly causing idle surges.

Why does my cat 3126 engine not shut off?

3126 engines don’t have a shutoff solenoid, it is all controled by the ECM. Most likely the speed sensors not sending signal, HEUI IAP valve, or even the HEUI pump itself. Longshot might be ECM. Unless you have an active code, the cruise flash codes won’t show anything.

What causes a Chevy C / K to stop running?

A leaky fuel pump will drain the line up to the carb, but about 15 seconds of cranking will fill the line again. 2. A sticking mechanical choke or a bad electric choke. Try; when you return to your truck from the Quicky Mart, put the accelerator slowly all the way to the floor, let your foot up slowly and then crank the engine.

What does no start no crank no click mean?

If you have a late model GM vehicle and turn the key only to hear nothing, you’ll most likely think you have a dead battery—and you may. But a no start, no crank, no click condition can be far more involved than that. In the old days, power flowed through the ignition switch and down to the starter solenoid. Not anymore.

Why is my GMC 7500 diesel engine not starting?

Since you have a 3126, I believe your fuel pressure regulator is faulty. I have seen this many times before. The regulator is located on the back of the head. When the fail, they allow fuel to leak out of the head and cause the engine not to start. Your engine needs 25 psi to start. If your engine has a hand primer pump, you can prime it up.

Why does my GM car say no start no crank?

How to diagnose a no start no click on GM vehicle. If you have a late model GM vehicle and turn the key only to hear nothing, you’ll most likely think you have a dead battery—and you may. But a no start, no crank, no click condition can be far more involved than that.

What is a typical GM starting system wiring diagram?

Click on the image here to pull up a PDF of a typical GM starting system wiring diagram. Depending on the year, model and engine of your GM vehicle, your starting system may be less complicated or use only some of the components shown here. For example, earlier anti-theft systems didn’t communicate the same way with the PCM.

What does Flash code 55 mean on GMC 7500?

Flash Code 55 indicates that No Detected Faults have occurred since the ignition key switch has been turned to the ON position. If you get a 2 digit code, I can tell you what it means and how to fix it.

Why does my car slow down when I push the gas?

It is in those situations that drivers will come to notice the obvious slow acceleration and the fact that the engine of their vehicle is struggling to keep up. This is a common problem in high mileage vehicles but there are no serious or immediate concerns regarding major engine problems.

Why does my car lose power going uphill?

Reasons Your Car Loses Power Going Uphill 1) Bad Fuel Filter. You can’t have a good working engine without fresh pure gasoline flowing into it at all times. If you don’t have a good fuel filter to prevent the impurities of the fuel from flowing into the engine, then it could ultimately jeopardize the performance of your engine.

Why does my car run when I release the gas pedal?

It would sometimes run normally if I release the gas pedal and press it again. What could be the problem? Thank you. It sounds like you may have an issue with your throttle position sensor. This sensor sends a reference voltage to your power-train control module, which uses that to determine ignition timing and fuel trims.

Why does my Chevy Silverado not go over 25 mph?

If so then remove the 2 closest to the engine, they are almost touching the manifold. If that helps then there is a blockage in the exhaust. Most likely a bad catalytic converter or a bent pipe.

Why does my car not accelerate when I press the gas?

If the power-train control module is not detecting the proper signal from the throttle position sensor, the engine may not accelerate properly. I would recommend having your throttle body inspected by a qualified mechanic, such as one from YourMechanic to determine why your car is slow to accelerate.

What causes a GM truck to lose power?

If your GM truck occasionally loses the ability to accelerate and warns you of reduced engine power, that could be caused by a faulty throttle body. While not common, this issue can interfere with your engine function and cause your vehicle to lose power anywhere from once in a while to several times in a day.

Why is my Chevy 8.1 L engine not working?

The electronic throttle control in the Chevy 8.1-L V8 engine can lose the signal between the accelerator pedal and throttle body. The throttle control normally sends a signal from the gas pedal and into the throttle body, telling it how much power is required. Once this signal is interrupted, the throttle body does not work correctly.

What kind of truck is a 2001 GMC Sierra?

I have a 2001 GMC Sierra 1500 SLT 5.3l that I bought used with only 80k miles on it. This truck starts then immediately stalls. Here is a list of things that I have replaced to no avail.

What causes a car to not start up?

The cause of this problem is usually one of 3 things – a failed starter motor, a bad connection between the battery and starter motor, or a blown fuse (if present) in line between the starter and the battery.

Are there any problems with the Chevy 8.1L Vortec?

The 8.1L was considered the diesel-alternative in the Chevy line and was designed to be big enough to produce comparable power and towing capabilities to that of the diesels. 1. Faulty Crankshaft Position Sensor – Vortec 8100 Out of all the problems on my list, this one is probably the most common and biggest pain.

How often do you need to change spark plugs on a Chevy 8.1?

The 8.1L Vortec is known for burning oil and leaving some laying around which results in the plugs becoming fouled. On the Chevy 8.1, the spark plugs need to be changed every approx. 25,000 miles. If you have serious oil burn issues then this could be more frequent as well. 5. Excessive Oil Consumption

When to know if your GMC Sierra fuel pump is bad?

If your car isn’t starting at all, and you hear the fuel pump prime that is usually a good indication that the pump is working to some capacity. Testing your Sierra’s fuel pressure on each side of the pump would be the best way to diagnose this problem.

How to troubleshoot the fuel pump on a GM 4.3L?

Troubleshooting the fuel pump (GM 4.3L, 5.0L, 5.7L) (for ‘Spider’ fuel system equipped vehicles). How To Test The Fuel Pump On GM TBI Fuel Systems (for throttle body fuel injection fuel system equipped vehicles).

How to check no fuel condition on GM 4.3L?

I’ve also included how to check a no fuel condition with starting fluid (although this is not the most effective way to test the fuel pump). It’s been my experience that misdiagnosing a bad fuel pump is a common occurrence on the 4.3L, 5.0L, 5.7L GM vehicles with the ‘Spider’ fuel injector assembly.

Can a fuel pump cause a no start condition?

CASE 1: If your fuel pressure gauge read 50 PSI or more as the engine cranked. This means that the fuel pump on your 4.3L, 5.0L, or 5.7L is OK and not the cause of your No Start Condition. The next step is to observe the fuel pressure gauge’s needle (after your helper stopped cranking the engine).

What to do if your GMC Sierra stall out?

69 people found this helpful. I have a 98 gmc searria 4×4 i checked fuel pressure it was under i changed fuel pump and fuel filter and its still starving for fuel what to do it starts with starting fluid 42 people found this helpful.

How does a GMC Sierra 1500 fuel pump work?

The older model has steel lines coming off of the top of the pump to the frame rail and then connects to the frame steel lines with short hoses, you’ll need line wrenches and the ability to curse. The newer style has plastic tubes from the plastic pump casing and uses those quick connect fuel fittings and you’ll need the disconnect tool.

What kind of car is a 95 Chevy?

I have a 95 chevy 1500 4×4 5.7L 145,000mils. It’s been running good/bad for a few months. It will start right up and idle ok in park but as soon as I put it into drive it stalls out.

Why does my GMC Sierra suddenly stop running?

Truck suddenly stops running, acting like it’s out of fuel. There is fuel in the gas tank and, I can hear the fuel pump when I turn the ignition on. Is there a fuse, or relay that is maybe causing this to happen?

What kind of engine does a 1995 Chevy Silverado have?

My 1995 Chevy k1500 Silverado 350 V8 stumbles and hesitates when i take off from a stop, it idles fine and runs fine My 1995 Chevy k1500 Silverado 350 V8 stumbles and hesitates when i take off from a stop, it idles fine and runs fine – Answered by a verified Chevy Mechanic

Why does my Chevy Silverado run out of fuel?

Another common reason that your Silverado may be starving for fuel is a bad fuel pump. The fuel pump is responsible for sending highly pressurized fuel to the fuel rails. The engine can die if the fuel pressure is not high enough to properly atomize the gasoline properly.

What should I do if my diesel truck won’t start?

Turn the key to the start position and allow the engine to crank for no more than 30 seconds. If the engine doesn’t start, turn the key to the off position and try the following: Plug the truck into an electrical outlet. Diesel trucks have a 3-prong plug located under the front bumper or grill area.

Is the GMC Duramax compatible with diesel fuel?

The Detroit News reports that GM is now facing a class-action suit alleging its 6.6-liter Duramax engine found in 2011-2016 Chevrolet and GMC models is not compatible with US diesel fuel.

Why are GM engines in so much trouble?

Details of the lawsuit, which was filed this week, say GM sold “hundreds of thousands” of engines containing a Bosch fuel injection pump that pumps metal shavings into the fuel injection system, ruining both the fuel system and the entire engine.

Why does my GMC diesel engine not work?

American diesel fuel is thinner than its European counterpart, allowing for air pockets that cause the metal to rub against metal and create shavings. “The pump secretly deposits metal shavings and debris throughout the fuel injection system and the engine until it suddenly and catastrophically fails without warning,” the lawsuit alleges.

Are there any problems with the Duramax diesel engine?

Overheating issues with the Duramax diesel seems to be a hit-or-miss problem; some owners experience it, while others never will. Regardless, it’s more common with the Duramax than other engines.

Is the GMC 6.5L diesel engine reliable?

Now it’s very reliable. I got a 1997 gmc with 115,000 miles on it its diesel and have 8 cylinders with 6.5 liter engine.. the fuel injector pump had been recalled back when we bought it and it was replaced a few times and gave us some problems for a few years after we bought it but has been fine since…..

Why is the lift pump not working on my GMC 6.5L diesel?

Another problem associated with the OPS is that the lift pump is supposed to send fuel through the IP and back to the tank, helping to cool the IP and the FSD= fuel solenoid driver, the little black box mounted on the driver’s side of the IP. This is basically the brain of the electronic IP.

What happens to the engine when left in idling position?

When the engine is left in idling position, it maintains a steady but low rate of revolution approximately 1,000 RPM. The RPM needle stays constant, and this indicates that the vehicle’s engine is receiving the correct amount of air and fuel.

Why does my car engine run rough while idling?

When your car engine runs as it should, everything should be smooth without any noise. When any number of things goes wrong, the engine can start running rough, especially while idling. By understanding the causes of a car engine that has a rough idle, you can resolve the issue easily.

How can I tell if my idle control motor is working?

Look for a difference in idle speed. Allow the engine to run for a minute so it settles to a consistent idle, then take note of any difference in the idle RPMs versus the idle you observed earlier. If the idle has not changed at all, it’s likely because your idle control motor has not been functioning.

What should the idle rate be on a 1997 GMC Truck?

Underdog, I don’t know the 1997 5.7, but 1000rpm sounds like a high idle, not where it should “bottom out”. A V8 should idle at 500rpm. GoNDown, did you recently disconnect your battery? After I left mine dead in the yard for a while and didn’t charge it, when I started it up it ran like you describe for a few days and then it was fine.

What should the idle speed be on a GMC V8?

A V8 should idle at 500rpm. GoNDown, did you recently disconnect your battery? After I left mine dead in the yard for a while and didn’t charge it, when I started it up it ran like you describe for a few days and then it was fine. I think it was doing a crank relearn (I no longer remember why I came up with that theory, though).

I have A 2004 GMC Sierra 1500 truck. Problem all gauges do not work all went out together. All other electrical work I have A 2004 GMC Sierra 1500 truck. Problem all gauges do not work all went out together. All other electrical work – Answered by a verified GM Mechanic We use cookies to give you the best possible experience on our website.

Why does my GMC Sierra stall when idling?

Stalling continues and now more often when idling, warm or cold. During idling the engine sputters and surges before it stalls. The dealer ship figures that the stalling and the PRV are two seperate issues. The only code that comes up is the faulty PRV.

Why is my idle control not working on my car?

If the idle has not changed at all, it’s likely because your idle control motor has not been functioning. If the idle control motor was working, disconnecting it should have created a difference in the engine’s idle. This test confirms there’s an issue with the idle control motor, but not what the issue may be.

Can a bad harmonic balancer cause an engine to shake?

If the harmonic balancer gets too old or fails and can no longer properly absorb the harmonic vibrations, the engine will shake excessively. The shaking will become even more pronounced, and therefore dangerous to the engine at high speeds.

When does the idle air control valve change?

When the engine is running but the vehicle is not moving, this means the engine is idling. During this time, the number of revolutions per minute (RPM) inside the engine will change. The idle air control valve is responsible for managing the engine idle speed.

Why is my GMC Sierra 1500 stalling out?

No change. Next, read somewhere that bad ground wire on Thermostat housing can cause ECM issues. Checked it, cleaned it off, verfied that contact wanhers are all steel and attract a magnet, reinstall the ground wire.

Can a bad idle control valve cause stalling?

This is controlled by the engine’s computer. Sometimes parts go bad, which results in your car idling strangely or stalling. Check to see if your idle control valve is functioning properly before attempting to replace it. Look for a high engine idle. A common symptom of a faulty idle control valve can be a high idle.

Why does my GM V8 engine misfire when cold?

Because, GM V8 engines are very prone to a rough idle and engine misfire when cold. The check engine light may also come on, with codes P0300, P0171 and PO174. But, as the engine warms up, the engine misfire or rough idle tends to go away; which seems confusing.

Is there an engine misfire code on a GM 4.8L?

Engine Misfire or Rough Engine Idle on GM 4.8L, 5.3L, 6.0L is becoming; more common and getting harder to diagnose. Because, GM V8 engines are very prone to a rough idle and engine misfire when cold. The check engine light may also come on, with codes P0300, P0171 and PO174.

What happens when one cylinder is not firing?

When one cylinder is not firing correctly, the engine will become unbalanced, and this can cause heavy vibrations inside your cabin on acceleration or at idle. 4. Check Engine Light Modern cars have great monitoring for all the different car sensors on the engine.

What makes a GM 4.8L misfire engine stall?

P0306: Cylinder #6 Misfire. P0307: Cylinder #7 Misfire. P0308: Cylinder #8 Misfire. Really bad gas mileage. Lack of Power when you accelerate your van, pickup or SUV. Engine may start, run for a few minutes and stall.

How to troubleshoot a GM Truck misfire?

This isn’t the only symptom that your GM van, pickup or SUV might experience… here are some more that you might see: P0300: Random Cylinder Misfire. P0301: Cylinder #1 Misfire. P0302: Cylinder #2 Misfire. P0303: Cylinder #3 Misfire. P0304: Cylinder #4 Misfire. P0305: Cylinder #5 Misfire. P0306: Cylinder #6 Misfire. P0307: Cylinder #7 Misfire.

How to troubleshoot a GM 4.8L 5.3L?

You can find this tutorial in Spanish here: Cómo Diagnosticar y Resolver Una Falla en Cilindro (GM 4.8L, 5.3L, 6.0L) (at: autotecnico-online.com ). The core symptom of a misfire is rough idle. This isn’t the only symptom that your GM van, pickup or SUV might experience… here are some more that you might see:

Why does my 6.5 Turbo Diesel not start?

Please try again later. 6.5 turbo diesel no start, we will see how easy it is to jump the glow plug relay and start the truck at any time we want. Diesel engines need the glow plugs to be nice and hot so the engine would be able to start. Thanks for watching this video. I hope this was a helpful one. God bless and we will see you in the next one.

What causes a Chevy truck to turn over but not start?

Plenty of turn over speed. With a test light there’s voltage at both sides of the coil but NO spark. Voltage at the throttle body injectors but NO fuel sprays. Fuel pump pumps. NO spark and NO fuel, turns fine. Rotor button turns, cap and rotor clean. Under the dash at the fuse panel there’s no voltage on the crank fuse.

What should I do if my engine won’t start?

You should see a bright spark jumping the gap in the spark tester. If you don’t see a spark, repeat the test. This time, adjust the spark tester to 30KV. If you still don’t see a spark, repeat the test and set the tester to 10KV. If this time you see a spark or no spark, you have a problem with the ignition system.

What causes a GMC truck to turn over but not start?

If the engine starts up normally after doing that, it means that fuel pressure is bleeding off and the fuel pump needs to prime the lines before it can start. It can bleed off from one of two places. 1. Fuel pressure regulator has an internal leak, and fuel is bleeding off back to the tank though the return line. 2.

What did I do when my engine wouldn’t start?

In any event, the “flight recorder” showed that there was good HP oil pressure while cranking, but sensor signals were not getting to the PCM to tell the injectors to fire. The repair was the replacement of the engine wiring harness.

The high pressure fitting can blow out to the point where the engine will not start at all – warm or cold. But running the engine on starting fluid will spin the high pressure pump fast enough to overcome some more severe leaks. Be aware that starting fluid is a stopgap measure, and the truck needs to be repaired soon…

What kind of engine cranks but won’t start?

Last evening after driving all day as usual, made one last stop (1/2) hour, left the barn and jumped in truck to go home- engine cranks mightily but won’t start – arggh!

SYMPTOM: Your 6.5L Diesel stalls just as if someone had reached over and turned off the ignition switch. CAUSE: There are two main causes. The first and most common is the PMD (also called FSD).

What should I do if my diesel engine stalls?

If you have codes P0251 or PO370, 17, 18, or any combination of those, you should consider the injection pump suspect. Tech Tip: If your truck stalls and will not re-start you can often get it going again by putting a cold wet rag on the PMD, or by carefully pouring a cup of cold water on it.

What causes a 6.5L diesel engine to not start?

“The PMD / FSD (Pump mounted driver) is by far the #1 cause of 6.5L no-starts (at least 90%). If your truck experienced random stalling like someone shut the key off before ultimately refusing to start again, the PMD is very likely the issue. Typically the random stalls caused by the PMD will become more frequent as the failure worsens.

Why does my car stall every time I put in gas?

I have trouble starting the vehicle every time I put gas in the car. It does not matter if I fill it up or not, just stalls. Only after I put gas in the car I have starting problems, after that the vehicle starts normally with no problems. I changed the purge valve with a new one and it work once with out hesitation.

Why do I have trouble starting my car?

My car has 218000 miles. My car has an automatic transmission. As you may know, this issue is commonly related to the evaporative emissions (EVAP) system which is comprised of a few components, one of which you have already addressed, the purge valve.

Why does my car stall when I Turn on the engine?

If your fuel pump quits or isn’t working properly, then your engine won’t get the fuel it needs to run, which results in the engine stalling. You won’t be able to restart your car if the fuel pump quits. 4.

What causes a car to stall on an incline?

Low fuel pressure. If your car only stalls on inclines, then low fuel pressure is likely the culprit. This can be the result of clogged injectors, so buy some fuel injector cleaner and add it to your fuel tank as soon as possible. 8. Dirty air filter.

What does it mean when your GMC Terrain won’t start?

The first and most common is when it won’t turn over. This just means that the engine doesn’t move when you turn the key. The second way that your Terrain won’t start is when the engine turns when you engage the starter, but it won’t fire and run on its own.

What are the symptoms of a fuel pump relay problem?

1. Engine stalls One of the first symptoms of an issue with the fuel pump relay is an engine that suddenly stalls. If the fuel pump relay has an issue while the vehicle is operating it will cut off power to the fuel pump, which will cause the engine to stall.

Why is my car engine hard to start?

The starter itself may not be cranking correctly due to the heat impacting the relays which drive the mechanisms (this was a common issue in old air cooled VWs, and with how some newer engines are crammed into engine bays similar things can happen).

How does the starter work on a GMC Sierra?

The starter in your GMC Sierra is dependent on three pieces of equipment. First, the ignition switch sends electrical current from the battery to the starter solenoid. The solenoid then forces the gear in the starter housing to engage the engine. When the starter motor turns on and spins the gear, the engine roars to life.

How to diagnose a starter motor problem?

Provides a procedure to follow to diagnose starter motor problems. One measurement I didn’t have time to add was to verify the solenoid operation by measuring the voltage drop across it while triggered. When you turn the key to START and you get 12V on the trigger wire, put one volt meter probe on the big silver solenoid battery cable nut .

What to do if your Chevy Silverado won’t start?

Cold Hard CHEVY Start Problem Solved! Chevrolet Silverado Express Suburban Tahoe GMC If playback doesn’t begin shortly, try restarting your device. Videos you watch may be added to the TV’s watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer.

Why is my Toyota Tacoma hard to start?

Q3: “ Toyota Tacoma starting problems – It’s incredibly hard to start when the outside air is hot.” A: For the hot start, hold the gas pedal to the floor while you turn the key to see if that does anything. If it helps then you may have a leaking fuel pressure regulator or fuel injector sending fuel into the intake on hot shut down.

What makes an internal combustion engine not start?

To operate efficiently, an internal combustion gasoline engine needs a good spark, the right amount of fuel, and good compression (a healthy mechanical condition). The lack of any of these three things will prevent your engine from starting.

Can a failed crank sensor cause no start?

The thing to remember about having a failed crank sensor, is that if you have spark or fuel injector pulses, the crank sensor is OK and not the cause of your No Start Condition. The crankshaft position sensor, on your 4.8L, 5.3L, 6.0L GM vehicle, is a Hall-Effect three wire crankshaft position sensor.

Last evening after driving all day as usual, made one last stop (1/2) hour, left the barn and jumped in truck to go home- engine cranks mightily but won’t start – arggh!

What happens if crankshaft sensor fails GM 4.8L?

If the crankshaft position (CKP) sensor fails, in your 4.8L, 5.3L or 6.0L GM vehicle, it’s not gonna’ start. In this article, I’ll show you how to test it using a multimeter (in Volts DC mode).

What to look for when your engine won’t start?

Check for a blown fuse that may be preventing a circuit from working properly, like the fuel injection or computer system. To operate efficiently, an internal combustion gasoline engine needs a good spark, the right amount of fuel, and good compression (a healthy mechanical condition).

What to do if your GMC Acadia won’t start?

It is definitely worth it to use an OBDII scannerto check and see if the engine has thrown any trouble codes. It is highly likely that if your Acadia won’t start that there will be codes. These codes will tell you what the computer is saying is wrong with your engine.

What to do if your GMC Yukon Denali won’t start?

48 people found this helpful. I have a 2000 Gmc Yukon denali, 5.7 litter, it cranks but won’t start it does have spark in coil, but No spark in #1 sparplug I put new distributor and new coil new sparplugs, new plug wires,checked out fuses there all good]

If you don’t hear it leave the key on while you hit the bottom of the fuel tank with a rubber hammer. then try to start it if this gets it started then you need a fuel pump. If it don’t then you need to check fuel pump fuses an relays. You need to get a proper diagnostic at a repair shop.

Why is my GMC Sierra 1500 not starting?

If a new car battery has been installed, the battery may not have yet reached its full capacity. There is nothing to worry about. A new battery only develops its full capacity over time. The voltage of the battery on your GMC Sierra 1500 can be measured precisely with a multimeter.

What’s the fuel pressure on a 1996 Chevy c1500?

I stuck a fuel pressure gauge on the fuel rail port and was reading about 50 psi. Unfortunately, as high as that sounds, the injectors won’t even open until you are at about 60 psi.

Can a car start without priming with gas?

Engine wont start until you prime the throttle body with fuel, then it starts and runs great! Clicking this will make more experts see the question and we will remind you when it gets answered.

Can a 1997 Chevy c1500 5.7L start?

1997 Chevy C1500, 2WD, 5.7L won’t start – cranks fine. No codes – good fuel pressure ( 60+ psi – new pump), good spark, 1997 Chevy C1500, 2WD, 5.7L wont start – cranks fine. No… It will not start. I changed the fuel filter and fuel pump It will not start.

Why does my 1997 Chevy Suburban not start?

1997 1500 pickup at low throttle engine is missing to the point were I had it full throttle and no power and engine died. Still won’t start … read more Vocational, Technical or Tra… i have a 1998 chevy suburban. It was running fine when parked, but 3 days later will not start. It cranks fine, but sounds as though it wants … read more

Which is the most powerful Duramax diesel engine?

The L5P duramax is the latest version of the Duramax V8 diesel engine. (engine code Y) Introduced in the 2017 model year it is the most powerful diesel engine GM has produced with 445 hp (332 kW) at 2,800 rpm and 910 lb⋅ft (1,234 N⋅m) at 1,600 rpm.

Where does the General Motors Duramax V8 engine come from?

Jump to navigation Jump to search. The Duramax is a General Motors V8 diesel engine family for trucks. The 6.6-liter Duramax is produced by DMAX, a joint venture between GM and Isuzu in Moraine, Ohio. The Duramax block and heads are poured at The Defiance GM Powertrain foundry in Defiance, Ohio.

When did the Duramax LML engine get an update?

The LML engine was significantly updated for 2011 to provide improved exhaust emissions that comply with the new federal emission standards for diesel engines, provide better engine rigidity and further noise reduction.

What kind of engine does GMC Sierra 3500HD have?

With a long box, the wheelbase is 167.6 inches and the overall length is 258.3 inches. The overall width for all models is 80.5 inches. The base engine in the 2019 GMC Sierra 3500HD is a 6.0-liter V8 gas engine that produces 360 horsepower and 380 pound-feet of torque.

The Detroit News reports that GM is now facing a class-action suit alleging its 6.6-liter Duramax engine found in 2011-2016 Chevrolet and GMC models is not compatible with US diesel fuel.

What is the towing capacity of a GMC Sierra 3500HD?

The maximum conventional towing capacity for a 2019 GMC Sierra 3500HD is 20,000 pounds. The maximum fifth-wheel tow rating is 23,100 pounds. A Trailering Camera System is available as a dealer-installed accessory.

Where to come when your 6.5L diesel will not start?

Where to come when your 6.5L Diesel will not start! “The PMD / FSD (Pump mounted driver) is by far the #1 cause of 6.5L no-starts (at least 90%). If your truck experienced random stalling like someone shut the key off before ultimately refusing to start again, the PMD is very likely the issue.