Most popular

Why does my 1997 Chevy c1500 not start?

Why does my 1997 Chevy c1500 not start?

1997 Chevy C1500, 2WD, 5.7L won’t start – cranks fine. No codes – good fuel pressure ( 60+ psi – new pump), good spark, 1997 Chevy C1500, 2WD, 5.7L wont start – cranks fine. No… It will not start. I changed the fuel filter and fuel pump It will not start. I changed the fuel filter and fuel pump relay.

What kind of car won’t start after hot?

Vocational, Technical or Tra… Have a 1998 Chevy Stepside Pickup C1500 That won’t start after it’s hot. After checking the fuel pressure (good 65+) now it won’t start. Replaced Fuel Pump

What to do if your Chevy 1500 won’t start?

The passlock sensor voltage reading has changed & you can relearn it to the PCM & you can start the truck again. To relearn, turn the ignition key to the on position for 3 10 minute cycles, turning the key to the off position for 5 seconds after each 10 minute learn.

Why does my car starter not crank when it’s Hot?

If your starter easily cranks a cold engine, but “drags” or cranks very slowly when hot, there may be a “heat soak” problem. Before you condemn the starter as bad, you should perform a system diagnosis of the battery, cables and starter.

Why does my Chevy Silverado not start when hot?

A clogged fuel filter, dirty fuel injectors or weak fuel pump can result in too little fuel reaching the cylinder, causing poor fuel ignition and the need to depress the accelerator to assist starting. An engine that is difficult to start when hot can be caused by a clogged air filter restricting airflow to the intake.

1997 Chevy C1500, 2WD, 5.7L won’t start – cranks fine. No codes – good fuel pressure ( 60+ psi – new pump), good spark, 1997 Chevy C1500, 2WD, 5.7L wont start – cranks fine. No… It will not start. I changed the fuel filter and fuel pump It will not start. I changed the fuel filter and fuel pump relay.

Vocational, Technical or Tra… Have a 1998 Chevy Stepside Pickup C1500 That won’t start after it’s hot. After checking the fuel pressure (good 65+) now it won’t start. Replaced Fuel Pump

The passlock sensor voltage reading has changed & you can relearn it to the PCM & you can start the truck again. To relearn, turn the ignition key to the on position for 3 10 minute cycles, turning the key to the off position for 5 seconds after each 10 minute learn.

Why does my 1997 Chevy Suburban not start?

1997 1500 pickup at low throttle engine is missing to the point were I had it full throttle and no power and engine died. Still won’t start … read more Vocational, Technical or Tra… i have a 1998 chevy suburban. It was running fine when parked, but 3 days later will not start. It cranks fine, but sounds as though it wants … read more

What kind of car won’t start at low throttle?

Vocational, Technical or Tra… 1997 1500 pickup at low throttle engine is missing to the point were I had it full throttle and no power and engine died. Still won’t start … read more Vocational, Technical or Tra… i have a 1998 chevy suburban. It was running fine when parked, but 3 days later will not start.

Can a fuel pump cause a no start condition?

CASE 1: If your fuel pressure gauge read 50 PSI or more as the engine cranked. This means that the fuel pump on your 4.3L, 5.0L, or 5.7L is OK and not the cause of your No Start Condition. The next step is to observe the fuel pressure gauge’s needle (after your helper stopped cranking the engine).

What should fuel pressure be on GM 4.3L Vortec?

You can find this tutorial in Spanish here: Cómo Probar La Bomba de Combustible (GM 4.3L, 5.0L, 5.7L) (at: autotecnico-online.com ). The fuel system in your 4.3L, 5.0L, or 5.7L Vortec engine needs at least 50 PSI of fuel pressure to start.

Why does my GM 4.3L engine not start?

No Start Condition Basics There are three very basic components that the engine, in your GM vehicle, needs to start and they are: Air, Fuel and Spark. When your 4.3L, 5.0L or 5.7L GM vehicle cranks but does not start, it’s because one of these components is missing from the mix.

CASE 1: If your fuel pressure gauge read 50 PSI or more as the engine cranked. This means that the fuel pump on your 4.3L, 5.0L, or 5.7L is OK and not the cause of your No Start Condition. The next step is to observe the fuel pressure gauge’s needle (after your helper stopped cranking the engine).

How to troubleshoot the fuel pump on a GM 4.3L?

Troubleshooting the fuel pump (GM 4.3L, 5.0L, 5.7L) (for ‘Spider’ fuel system equipped vehicles). How To Test The Fuel Pump On GM TBI Fuel Systems (for throttle body fuel injection fuel system equipped vehicles).

You can find this tutorial in Spanish here: Cómo Probar La Bomba de Combustible (GM 4.3L, 5.0L, 5.7L) (at: autotecnico-online.com ). The fuel system in your 4.3L, 5.0L, or 5.7L Vortec engine needs at least 50 PSI of fuel pressure to start.

What’s the difference between no start and no crank?

It’s important to know that a no crank and a no start condition are not the same thing since this article only concentrates on testing a no start condition. In layman’s terms, a No Start Condition means that your vehicle’s starter motor is cranking the engine but the engine is not starting.

What does it mean when your car says no start?

A No Crank Condition means that the engine is not turning over when you turn the key to crank the engine. The most common problem, that causes this condition is a failed starter motor. If your vehicle is suffering a No Crank Condition, this tutorial may be a good starting point: How To Test The Starter Motor (GM 4.3L, 5.0L, 5.7L).

1997 1500 pickup at low throttle engine is missing to the point were I had it full throttle and no power and engine died. Still won’t start … read more Vocational, Technical or Tra… i have a 1998 chevy suburban. It was running fine when parked, but 3 days later will not start. It cranks fine, but sounds as though it wants … read more

Why does my car engine not want to start?

If the engine still doesn’t seem like it wants to start, probably fuel is getting into the cylinders and your problems lies somewhere else. However, if the engine runs momentarily and dies, then the problem is that fuel is not getting to the cylinders. Check for a clogged fuel filter, or a bad fuel pressure regulator.

What causes a car to stall with no spark?

Consequently, An old or failing ignition pickup may cut out signal intermittently, which may cause the engine to stall. The engine may suddenly just shut off, almost as if the key had been turned off. Depending on the nature of the issue, sometimes the vehicle can be restarted and driven.

What does it mean when a Chevy truck won’t start?

It has spark as evidenced by putting an old spark plug into a spark plug wire and grounding the plug After spraying a small amount of starting fluid into the air intake tube, the engine starts for just a moment, then dies Three or four years ago the truck had the Reduced Engine Power warning problem.

Why is the engine cranking but not starting?

I borrowed a Noid Lite Set from AutoZone and checked the wires to three of the injectors—the light flashed on all three while I cranked the engine. So, the ECM is sending power to these injectors, and I assume to the others as well.

It has spark as evidenced by putting an old spark plug into a spark plug wire and grounding the plug After spraying a small amount of starting fluid into the air intake tube, the engine starts for just a moment, then dies Three or four years ago the truck had the Reduced Engine Power warning problem.

I borrowed a Noid Lite Set from AutoZone and checked the wires to three of the injectors—the light flashed on all three while I cranked the engine. So, the ECM is sending power to these injectors, and I assume to the others as well.

Why does my GMC Sierra engine not start?

It seems this can also be caused by faulty APP (Accelerator Pedal Position) sensor. First I would check the INJ1 and INJ2 fuses in the under the hood fuse box.

What’s the fuel pressure on a 1996 Chevy c1500?

I stuck a fuel pressure gauge on the fuel rail port and was reading about 50 psi. Unfortunately, as high as that sounds, the injectors won’t even open until you are at about 60 psi.

Why does my 96 Chevy Express van not start?

Also had a similar issue spin and no start with a 96 Chevy Express Van with the 5.7L. This vehicles issue turned out to be a shorted pink wire in the wiring harness that runs up the passenger side of the block. The vehicle had died while driving several times and wouldn’t start. Then, finally after blowing a couple fuses, would start at all.

What kind of truck is a 96 Chevy?

– CarGurus 96 Chevy C1500 5.7L Vortec Truck won’t start, Replaced Fuel Pump, Filter & Has Spark.

Why does my GM pickup engine not start?

How To Test The Fuel Pump On GM TBI Fuel Systems (for throttle body fuel injection fuel system equipped vehicles). A failure in one of the Passlock system’s components will cause the engine to start and then stall after a few seconds. This is due to the fact that the PCM, in your GM pickup or SUV, has disabled the fuel injectors.

Also had a similar issue spin and no start with a 96 Chevy Express Van with the 5.7L. This vehicles issue turned out to be a shorted pink wire in the wiring harness that runs up the passenger side of the block. The vehicle had died while driving several times and wouldn’t start. Then, finally after blowing a couple fuses, would start at all.

How to know if your engine has no spark?

First Confirm Your Engine Has No Spark. 1 Disable the fuel system by removing the fuel pump fuse or relay. 2 Insert a spark plug tester into the plug boot and ground it on a piece of metal on the engine. 3 Finally, Have someone crank the engine and watch for spark.

Why does my car not start when I crank the engine?

The crankshaft position (CKP) sensor monitors the position or rotational speed of the crankshaft. If the crankshaft position sensor has failed completely, and isn’t sending a signal to the (ECU) at all, then the computer won’t send any fuel to the injectors. This will leave you unable to start the car.

First Confirm Your Engine Has No Spark. 1 Disable the fuel system by removing the fuel pump fuse or relay. 2 Insert a spark plug tester into the plug boot and ground it on a piece of metal on the engine. 3 Finally, Have someone crank the engine and watch for spark.

It’s important to know that a no crank and a no start condition are not the same thing since this article only concentrates on testing a no start condition. In layman’s terms, a No Start Condition means that your vehicle’s starter motor is cranking the engine but the engine is not starting.

The crankshaft position (CKP) sensor monitors the position or rotational speed of the crankshaft. If the crankshaft position sensor has failed completely, and isn’t sending a signal to the (ECU) at all, then the computer won’t send any fuel to the injectors. This will leave you unable to start the car.

Why does my Chevy Silverado not want to accelerate?

If the catalytic converter gets too clogged up, it’ll keep the motor from accelerating properly. It’ll “bog” after a certain speed. Maybe it’ll drive 20 miles an hour just fine, but after that it just doesn’t want to accelerate whatsoever. This can also be a sign that it’s not getting enough fuel as well.

Why does my Chevy Silverado not move in first gear?

Slipping means that it loses its grip on the flywheel and it feels like you’ve pushed the clutch in. This will usually happen at highway speed, under heavy acceleration. It only gets worse as the clutch disk slips, burns up, and can handle less and less torque. Eventually it’ll only move in first gear or not at all.

If the catalytic converter gets too clogged up, it’ll keep the motor from accelerating properly. It’ll “bog” after a certain speed. Maybe it’ll drive 20 miles an hour just fine, but after that it just doesn’t want to accelerate whatsoever. This can also be a sign that it’s not getting enough fuel as well.

Slipping means that it loses its grip on the flywheel and it feels like you’ve pushed the clutch in. This will usually happen at highway speed, under heavy acceleration. It only gets worse as the clutch disk slips, burns up, and can handle less and less torque. Eventually it’ll only move in first gear or not at all.

What causes a 6.5L diesel engine to not start?

“The PMD / FSD (Pump mounted driver) is by far the #1 cause of 6.5L no-starts (at least 90%). If your truck experienced random stalling like someone shut the key off before ultimately refusing to start again, the PMD is very likely the issue. Typically the random stalls caused by the PMD will become more frequent as the failure worsens.

What kind of engine does a 1997 Chevy c1500 have?

Chevy c1500: 1997 chevy 2wd c1500 wit 5.7 engine. 268, miles. 1997 chevy 2wd c1500 wit 5.7 engine. 268,xxx miles. I have been a lot of spark knock when truck is under a load going up hils. don’t really notice it … read more

Can a Chevy C / K 1500 run without fuel?

Also I haven’t fully checked the Spark, but the Truck run’s fine when you spray Starting fluid into the Throttle body. Any suggestions on why the truck isn’t accepting the fuel, it cranks fine, just wont run without starting fluid. these trucks have to have between 55-65psi of fuel to run.

Chevy c1500: 1997 chevy 2wd c1500 wit 5.7 engine. 268, miles. 1997 chevy 2wd c1500 wit 5.7 engine. 268,xxx miles. I have been a lot of spark knock when truck is under a load going up hils. don’t really notice it … read more

Also I haven’t fully checked the Spark, but the Truck run’s fine when you spray Starting fluid into the Throttle body. Any suggestions on why the truck isn’t accepting the fuel, it cranks fine, just wont run without starting fluid. these trucks have to have between 55-65psi of fuel to run.

No Start Condition Basics There are three very basic components that the engine, in your GM vehicle, needs to start and they are: Air, Fuel and Spark. When your 4.3L, 5.0L or 5.7L GM vehicle cranks but does not start, it’s because one of these components is missing from the mix.

Why does my car not start when I start it?

There are three very basic components that the engine, in your GM vehicle, needs to start and they are: Air, Fuel and Spark. When your 4.3L, 5.0L or 5.7L GM vehicle cranks but does not start…it’s because one of these components is missing from the mix.

Why does my car not start when I turn the key?

This condition is usually due a failed fuel pump, a failed ignition coil, a failed ignition control module, a failed crank sensor, etc… that lets the engine crank (turn over) but does not let it start. A No Crank Condition means that the engine is not turning over when you turn the key to crank the engine.

Why is my Chevy Silverado not cranking over?

Since you have voltage on the crank fuse while in crank position, we know the ignition switch is good. The pcm supplies the ground to the starter relay to turn on the starter. It is possible if the wiring is good, there is a problem with the pcm.

What kind of truck cranks but won’t start?

Truck cranks but won’t start – 1997 Chevy C1500 chevrolet… I have a 1997 Silverado with the 4.3 vortec motor. About 2 weeks ago my son was driving it and the way he explained it was the engine completely died on him, causing his guages to malfunction and his steering wheel to lock up.

What should I do if my Chevy Silverado wont start?

Connect a 30-amp fused jumper between the battery positive voltage circuit of the starter relay switch circuit and the supply voltage circuit of the starter solenoid. Does the engine crank?

Truck cranks but won’t start – 1997 Chevy C1500 chevrolet… I have a 1997 Silverado with the 4.3 vortec motor. About 2 weeks ago my son was driving it and the way he explained it was the engine completely died on him, causing his guages to malfunction and his steering wheel to lock up.

A No Crank Condition means that the engine is not turning over when you turn the key to crank the engine. The most common problem, that causes this condition is a failed starter motor. If your vehicle is suffering a No Crank Condition, this tutorial may be a good starting point: How To Test The Starter Motor (GM 4.3L, 5.0L, 5.7L).

Why does my Chevy Silverado truck not start?

The starting problems of a vehicle can be different. In some cases the truck starts at least sporadically and allows its owner to drive independently to the nearest specialist workshop. In other cases, the truck won’t start until the underlying problem is solved. The nature of the starting problems depends on their cause.

What causes a car to have a no start problem?

A blown fuse in the starter circuit could be the cause of a no-start problem. Broken or corroded wiring – Damaged or dirty wires to the battery or to the starter solenoid (or wires that are loose) can prevent sufficient power from reaching the starter.

Why does my car say it has a bad starter solenoid?

Problems that might cause your car to act like it has a bad starter solenoid can include: Bad battery – If the battery voltage is low it will be unable to provide enough power to start your engine. Blown fuse – Sometimes the simplest explanation is the best one. A blown fuse in the starter circuit could be the cause of a no-start problem.

What kind of car has no crank no start?

This topic contains 5 replies, has 4 voices, and was last updated by shin_gle 7 years, 9 months ago. I have a no crank/no start situation with my 97 chevy C1500.

This condition is usually due a failed fuel pump, a failed ignition coil, a failed ignition control module, a failed crank sensor, etc… that lets the engine crank (turn over) but does not let it start. A No Crank Condition means that the engine is not turning over when you turn the key to crank the engine.

This topic contains 5 replies, has 4 voices, and was last updated by shin_gle 7 years, 9 months ago. I have a no crank/no start situation with my 97 chevy C1500.

Can a Chevy C / K 1500 engine not start?

Chevrolet C/K 1500 Questions – truck will not start, engine turns, but does not fire at all. – CarGurus truck will not start, engine turns, but does not fire at all. other computer-related things that could be interfering?

The starting problems of a vehicle can be different. In some cases the truck starts at least sporadically and allows its owner to drive independently to the nearest specialist workshop. In other cases, the truck won’t start until the underlying problem is solved. The nature of the starting problems depends on their cause.

Why does my Chevy truck crank but not start?

I found that the fuel pump was out. So, after replacing the fuel pump and filter, it still would not fire, it will crank but no fire. I then rechecked the fuese, relays and so on. I found that the ignition coil was out, so after replacing it, still no fire.

I found that the fuel pump was out. So, after replacing the fuel pump and filter, it still would not fire, it will crank but no fire. I then rechecked the fuese, relays and so on. I found that the ignition coil was out, so after replacing it, still no fire.

What does it mean when a truck won’t start?

It might be the computer, but it might be a sensor or a $10 relay. You won’t get diagnostics through the internet. I have a 1998 Chevy 2500 w/ a 5.7 that wouldn’t start even though the truck had good spark, fuel in the tank, and I could hear the pump spin up and pressurize when I turned the key.

What’s the problem with my Chevy Silverado 1500?

When it decides to act right, all is will. Anyone else found a solution? Chevy silverado 1500 2004. The same problem, random intermittent starting. I had had this problem before about 5 times and each time I disconnected and reconnected the negative battery cable it started fine. This time that didn’t work.

If the engine doesn’t crank, or makes an unusual noise when cranking, you may have a starting system problem. The car’s security system may have made an error that disabled the fuel or ignition system, or the chip in the key may have failed.

Why does my Chevy Silverado not start up?

Few things are as annoying as turning the key in your truck and finding it will not start. There are many problems that can result in a Chevy Silverado’s failure to start, making diagnosing the trouble even more frustrating.

Why does my 350 Chevy truck not start?

350 chevy truck cranks but won’t start – Maintenance/Repairs – Car Talk Community Truck ran fine with no indication of problem. When outside temp. dropped in teens one morning it wouldn't start.

Why is my Chev k1500 350 Vortec not starting?

So I went and bought a sensor installed it and forgot to reset the computer before trying to start it. It changed nothing, still the same old problem. So I decided to reset the computer by disconnecting the battery, a good 10 to 15 minutes or so. Hooked it back up and still has the same problem.

What to do if your Chevy truck won’t crank?

Found no spark. Replace HEI distributor and no start. Have replaced spark plugs, had starter and battery tested. All are good. Edelbrock 600cfm carb is 6 months old. Truck was completely restored 20000 miles ago so mechanically it’s a new truck. I have no idea why it won’t crank. Buying Guides Deals Car Reviews Repair Shops Community Cars A-Z

350 chevy truck cranks but won’t start – Maintenance/Repairs – Car Talk Community Truck ran fine with no indication of problem. When outside temp. dropped in teens one morning it wouldn’t start.

So I went and bought a sensor installed it and forgot to reset the computer before trying to start it. It changed nothing, still the same old problem. So I decided to reset the computer by disconnecting the battery, a good 10 to 15 minutes or so. Hooked it back up and still has the same problem.

What causes a Chevy truck to turn over but not start?

Plenty of turn over speed. With a test light there’s voltage at both sides of the coil but NO spark. Voltage at the throttle body injectors but NO fuel sprays. Fuel pump pumps. NO spark and NO fuel, turns fine. Rotor button turns, cap and rotor clean. Under the dash at the fuse panel there’s no voltage on the crank fuse.

Plenty of turn over speed. With a test light there’s voltage at both sides of the coil but NO spark. Voltage at the throttle body injectors but NO fuel sprays. Fuel pump pumps. NO spark and NO fuel, turns fine. Rotor button turns, cap and rotor clean. Under the dash at the fuse panel there’s no voltage on the crank fuse.

If the engine doesn’t crank, or makes an unusual noise when cranking, you may have a starting system problem. The car’s security system may have made an error that disabled the fuel or ignition system, or the chip in the key may have failed.

What causes the fuel pump to not start?

The fuel pump is running and delivering normal pressure to the engine But, with all that working your engine still will not start. So, the most likely cause, is that the fuel injectors are probably not opening. The (PCM) uses the trigger signal from the crankshaft position sensor; and/or camshaft position sensor to pulse the injectors.

What to look for when your engine won’t start?

Check for a blown fuse that may be preventing a circuit from working properly, like the fuel injection or computer system. To operate efficiently, an internal combustion gasoline engine needs a good spark, the right amount of fuel, and good compression (a healthy mechanical condition).

What kind of Chevy truck won’t start?

In this video we encounter a condition where a 2002 Chevy Silverado ( Similar to GMC Sierra ) pickup has a symptom of the engine cranks over but won’t start…. In this video we encounter a condition where a 2002 Chevy Silverado ( Similar to GMC Sierra ) pickup has a symptom of the engine cranks over but won’t start….

What to do if your GMC Sierra 1500 wont start?

If you discover white deposits or silvery-green deposits, but no further cracks or damage, you do not have to replace the battery, just clean it. To clean the battery on your GMC Sierra 1500, you have to remove the pole cables first, which requires no special knowledge, just a little concentration, as the order is very important.

There are three very basic components that the engine, in your GM vehicle, needs to start and they are: Air, Fuel and Spark. When your 4.3L, 5.0L or 5.7L GM vehicle cranks but does not start…it’s because one of these components is missing from the mix.

What makes a Chevy 1500 turn over and stall?

What happens is the passlock sensor creates a certain voltage reading under 5 volts & the PCM has to learn that voltage or it will start & stall until it does. The passlock sensor voltage reading has changed & you can relearn it to the PCM & you can start the truck again.

What to do if your ignition key won’t turn?

This feature is not available right now. Please try again later. Sometimes the ignition key won’t turn or rotate. If that happens the vehicle won’t start, the steering wheel won’t turn and it won’t shift into gear. On a late 90’s or early 2000 GM vehicle this is the way to get it apart so you can replace the tumbler. Loading…

This feature is not available right now. Please try again later. Sometimes the ignition key won’t turn or rotate. If that happens the vehicle won’t start, the steering wheel won’t turn and it won’t shift into gear. On a late 90’s or early 2000 GM vehicle this is the way to get it apart so you can replace the tumbler. Loading…

What kind of truck won’t start after sitting?

Repair manuals and support for cars and trucks manufactured by Chevrolet, a division of General Motors. 2003 S10 V6. If the truck is started everyday it starts right up with no problems. If left sitting for at least 24 hours it is hard to start it.

What causes a Chevy Silverado to start without turning the engine?

A fuel delivery problem is usually caused by a clogged fuel filter, no fuel in the tank or a faulty fuel pump. A starter that spins without turning the engine is caused by the starter gear failing to engage the engine’s flywheel.

Why does my GM car say no start no crank?

How to diagnose a no start no click on GM vehicle. If you have a late model GM vehicle and turn the key only to hear nothing, you’ll most likely think you have a dead battery—and you may. But a no start, no crank, no click condition can be far more involved than that.

Why does my car sputter when I drive?

Driving should be smooth. But, if you are driving and your car’s engine starts sputtering the first cause of concern would be low fuel. However, if your fuel gauge is full it could be a symptom of further engine problems. A blocked fuel injector can prevent fuel from reaching the combustion chambers.

What should I do if my long crank wont start?

Just a recap of what you should do first to determine if your long crank before starting is fuel related or not. First, before you try cranking the engine over, turn the ignition key to the run position then back off without cranking the starter.

What should fuel pressure be on a 1997 Chevy c1500?

Pressure should be 55-62 minimum according to GM. Probably pump, pressure regulator i did another fuel pressure test, KOEO, this time with the return fuel line blocked off. my pressure went to 55psi til the pump stopped and then still dropped to 20psi. does that tell me its not the pump??? anyone??

The fuel pump is running and delivering normal pressure to the engine But, with all that working your engine still will not start. So, the most likely cause, is that the fuel injectors are probably not opening. The (PCM) uses the trigger signal from the crankshaft position sensor; and/or camshaft position sensor to pulse the injectors.

Pressure should be 55-62 minimum according to GM. Probably pump, pressure regulator i did another fuel pressure test, KOEO, this time with the return fuel line blocked off. my pressure went to 55psi til the pump stopped and then still dropped to 20psi. does that tell me its not the pump??? anyone??

Why does my Chevy truck not start when it gets cold?

Seems to be fuel pressure but can’t smell any gas like it was flooding. It does’nt even fire like it wants to start. It has been starting hard and I would have to turn key on and off 4 or 5 times before I could get it to start but once it started it would run just fine. has any chevy owners out there delt with this before??

Why does my 97 Chevy truck not start?

97 Chevy truck won’t start when it gets cold?? When ever it gets cold my truck will not start. Seems to be fuel pressure but can’t smell any gas like it was flooding. It does’nt even fire like it wants to start.

Can a 1997 Chevy c1500 5.7L start?

1997 Chevy C1500, 2WD, 5.7L won’t start – cranks fine. No codes – good fuel pressure ( 60+ psi – new pump), good spark, 1997 Chevy C1500, 2WD, 5.7L wont start – cranks fine. No… It will not start. I changed the fuel filter and fuel pump It will not start.

What was the issue with my 1997 Chevy P / U?

Having an issue with starting a 1997 Chevy P/U. Issue started a few months back when after having the truck running for a while then stopping it for a short time and then restarting, the starter would start, stop, start and then catch.

Is there a problem with my Chevy Silverado?

Will turn key and it is like no power from battery to starter, but have lights, radio, etc. Turn key again or sometimes multiple times, to no avail. Then, turn it one more time and it starts. Then the next 15 starts, no problem. Sometimes hot engine, sometimes cold. UPDATE: 2-6-14; I sold the truck to my father. He changed the starter.

What causes a car to not start with no spark?

Without spark, the engine will Crank but Not Start. The ignition system of the GM vehicles covered by this article use a distributor type system. In my experience, the most common component failures, of the ignition system that cause a No Start No Spark Condition are: Distributor cap. Crank sensor.

Without spark, the engine will Crank but Not Start. The ignition system of the GM vehicles covered by this article use a distributor type system. In my experience, the most common component failures, of the ignition system that cause a No Start No Spark Condition are: Distributor cap. Crank sensor.

Having an issue with starting a 1997 Chevy P/U. Issue started a few months back when after having the truck running for a while then stopping it for a short time and then restarting, the starter would start, stop, start and then catch.

What causes a car to not start after running out of gas?

Therefore most knock sensor faults or issues should have little to no effect on the operation of the… If the engine was sputtering and then when the exhaust starts to come off it makes the engine run better, then there is either a plugged muffler or a plugged catalytic converter.

Why does my car not start after filling up the gas tank?

If that doesnt work, get a fuel pressure test done. The results of the test will let you know more. It could be a vacuum leak. Every time you open the fill cap, the pressure is leaving the system and without a good vacuum it will take time for the fuel to move through the rail to the cylinders.

Is there a fuel problem with cranks but wont start?

yes unless you can get your hands on a lift and drop it out that would be much easier. If its the first time its been changed it will prob be a bit a of a job. Especially if you drop it and u have a lot in the tank. And when your removing the actual pump be real careful nothing falls inside or u will have bigger problems. Re: Cranks but wont start.

What is the fuel system on a 1997 Chevy Blazer?

The fuel system in your 1997 Chevy S-10 Blazer consists of an in-tank fuel pump, fuel injectors and an on-board computer. By isolating each component and testing separately from the other parts, the cause of failures can easily be found.

It might be the computer, but it might be a sensor or a $10 relay. You won’t get diagnostics through the internet. I have a 1998 Chevy 2500 w/ a 5.7 that wouldn’t start even though the truck had good spark, fuel in the tank, and I could hear the pump spin up and pressurize when I turned the key.

– CarGurus 96 Chevy C1500 5.7L Vortec Truck won’t start, Replaced Fuel Pump, Filter & Has Spark.

What does it mean when your GMC Sierra won’t start?

The first and most common is when it won’t turn over. This just means that the engine doesn’t move when you turn the key. The second way that your Sierra won’t start is when the engine turns when you engage the starter, but it won’t fire and run on its own.

Why does my GMC Yukon engine not start?

GMC Yukon: Engine Cranks → Won’t Start There are a lot of issues that can cause your Yukon to crank, but not start. The engine needs air, fuel, and a spark in order to run. It is highly likely that if the engine is cranking, but not starting that it has thrown an OBDII code.

How to hard start a 98 Chevy 5.7L?

Definitely start looking at your fuel supply Fairfield,CT. Fuel pump. Do not use aftermarket if you replace it. Use AC Delco or GM otherwise you will be doing it twice. Try turning the key on, wait 5 to 10 seconds – then crank. We have a 5.7 that if you just crank, it cranks for the 10 seconds.

Is the 1998 Chevy Silverado 5.7L hard to start?

Hello all, My 1998 chevy silverado 5.7L Vortec used to start as soon as you bump the key, and now it is hard to start (mainly when its cold) it takes several cranks of the engine to start and after truck warms up its okay, usually in the morning or if the truck sits for several hours after running. (i.e.

Why does my Chevy Silverado not crank up?

Fuel pump, fuel filters are big cause of pumps failing because no one changes them and makes pump strugle then fail If everything is good and it will not crank? Then you need to reprogram your key to truck. Lots of problems with GM and the security system failing. 1 people found this helpful.

It seems this can also be caused by faulty APP (Accelerator Pedal Position) sensor. First I would check the INJ1 and INJ2 fuses in the under the hood fuse box.

There are a lot of issues that can cause your Sierra to crank, but not start. The engine needs air, fuel, and a spark in order to run. It is highly likely that if the engine is cranking, but not starting that it has thrown an OBDII code.

What causes a car to crank but not start?

One of the biggest issues that causes a vehicle to crank but not start is ignition issues. When there is no spark, the engine will not start. You’ll probably have a misfire related code such as P0300, P0301, etc…..

Author Image
Ruth Doyle