Why are the brake lights on my Chevy 1500 not working?

I have a 1994 Chevy 1500. Brake lights are not working. I replaced the bulbs and the brake light switch. All the other Chevrolet Repair Questions? Ask a Chevy Mechanic for Answers ASAP By continuing to use this site you consent to the use of cookies on your device as described in our cookie policy unless you have disabled them.

What makes the brake lights come on on a 1998 Silverado?

It does look like a bracket, that wraps around the brake pedal arm. When the brake pedal is pressed down it pushes the cylinder switch together which closes the circuit and makes you brake lights come on. Check your fuses as well as your wiring to the brake light housing. Also make sure that you have working bulbs and the right bulbs are inserted.

Where are the brake lights on a Chevy C / K 1500?

There is a break light relay I think down under drivers side, or under the hood in the fuse box. Blinkers are working so the circuit is good. 32 people found this helpful. Thanks Rowefast, it was the brake light relay.

What kind of brake lights are not working?

I have a 1994 Chevy 1500. Brake lights are not working. I… i have a 1994 Chevy… i have a 1994 Chevy 1500. Brake lights are not working. I replaced the bulbs and the brake light switch.

Why are my brake lights not working on my 1997 Chevy?

Pull the plastic cap off the fuse chassis and you’ll see a square relay fuse switch and replace it for the brakes. It’s only $13 bucks and is the predominant issue with 1997 Chevy Trucks and the brakes not working especially if you reverse and blinker lights do work. Was this answer helpful? Its the taillight circuit board or a broken wire.

Where is the brake light switch on a 1998 Silverado?

The brake light switch is on the arm from the brake pedal to the brake booster (under the hood). It is held in place by a snap clip that is nearly impossible to get off, so don’t. Buy your switch and a new snap clip and then take a large screwdriver and shove it between the top of brake petal and the switch.

Why is the warning light on my Chevy c2500 not working?

The most obvious culprit is the switch located immediately under the parking brake pedal. If this malfunctions, the warning light may glow even if the brake has been released. Check this first and rule it out as a possible cause. This is a known issue on Chevy C1500 pickup trucks equipped with rear-wheel anti-lock (RWAL) brake systems.

Can a brake light switch not be installed?

In many cars, there is a special procedure to remove and install the brake light switch. If not installed correctly, the switch will not operate and can even be damaged. In some cars, the gap between the brake pedal and the switch must also be adjusted.

Where are the 3rd brake lights on a Chevy 1500?

The 3rd brake light is on a seperate circuit from the brake lights . Test for power at the brake switch.Orange is 1 and white is the other,they are next to each on the switch.If that checks out try fiddling with the hazards and turnsinals since the brake light power flow goes form the brake switch to the turnsignals.

What are the symptoms of a bad brake light switch?

The most common symptom of a faulty brake light switch is when brake lights don’t come on or stay on all the time. A faulty brake light switch can cause many problems. If a switch is bad, the brake lights won’t operate and the transmission shifter will not come out of “Park” position.

My 1994 chevy 1500 brake lights, head lights, front parking lights and front and rear turn signals work……TAIL LIGHTS do NOT work…..have checked fuses and bulbs…..What could the problem be??? If you have checked to be sure there is 12V to the lights check further to be sure there is a solid ground path.

What causes brake lights to not work but tail lights do?

5 Causes of Brake Lights Don’t Work But Tail Lights Do 1 Bad Light Bulbs 2 Bad Brake Light Switch 3 Broken fuse or fuse box 4 Bad sockets and connectors 5 Broken wire More …

Where are the brake lights on a Chevy Silverado?

Check the Brake Lights Circuit. Start at the fuse box under the hood and make sure the brake lights fuse is not blown, that the terminals are free of corrosion and that the connections are tight. Then check the brake light switch on the bake pedal arm. Back probe the switch terminals with a test light.

What should I do if my brake light wont turn on?

Only one of the switch terminals should turn on the test light. When you depress the brake pedal, both switch terminals should turn on the test light. If only one of the wires turns on the test light, unplug the switch and jump the two connections at the connector.

Why are the brake lights not working but the tail lights are?

Blown out light bulbs are the most common reason for why the brake lights not working but the tail lights are. Remove the screws from the bulb lens (which you can access through the trunk or see your vehicle repair manual to get the exact location). Push the bulbs and turn them counterclockwise to remove from the socket.

Where is the brake light switch on my car?

Fuse Box and Light Switch. You have to find the fuse box or the power distribution center (PDC). You will get the fuse panel under the dashboard and the PDC under the hood. The brake light switch is also to be found under the dashboard and check if its plunger touches the brake pedal arm.

Are there any lights on in my car?

Brake lights and signal lights work but tail lights were not on. Had to use my flashers to get home safely. My car has 105 miles. My car has an automatic transmission.

Why are the lights not working on my Chevy Silverado?

You might have an electrical problem. The first step is to have your local Chevrolet dealer or mechanic check your switch as well as ensure power is running to the sockets. Next, your dealer or mechanic should check your electrical system. If your bulbs persistently burn out, you might be using the wrong wattage.

What causes a burnt out light bulb on a Chevy?

A burnt out bulb is usually discolored and pieces of the filament will be loose inside the bulb. If a visual inspection shows the bulb is still good, there may also be a broken wire in the harness to that light.

What to do if your Chevy Silverado wont turn on?

While you might need to work under the hood of your truck to resolve this common problem, you can rest assured that you won’t be stuck attempting to carry out advanced repair work that requires specialized skills or tools.

Why are the headlights not working on my Chevy?

A wiring issue will require a check of wires with a multimeter with the help of your vehicle’s schematics. Only the low-beams or high-beams work: If your headlights both work but only when the low-beams or high-beams are on, the problem is likely with the dimmer switch.

What to do if your license plate light is not working?

If everything works but the license plate lights, first make sure there isn’t power to the lock sockets. If there isn’t, trace the power wire back to where it connects with the other tail lights. If there is power, then replace the sockets.

Why are the rear lights on my 91 k1500 not working?

I had the same problem on my 91 K1500. The most common reason rear lights of any kind will fail is rotted wires. They run through wire shroud from front to back along the inside of the frame to the left tail light. Running this way leaves them exposed to the elements.

I have a 1994 Chevy 1500. Brake lights are not working. I… i have a 1994 Chevy… i have a 1994 Chevy 1500. Brake lights are not working. I replaced the bulbs and the brake light switch.

When did 2007 suburban cruise control brake switch arrive?

(Just google ‘2007 suburban cruise control brake switch’ for many hits including the video) I decided to take a $10 gamble and ordered the switch on a Thursday and it arrived Saturday morning.

What are the fuses on a 2002 Avalanche?

Make and Model > Chevrolet > Avalanche > 2002 Chevrolet Avalanche… IGN A Fuse #3 40A Starter Relay, Ignition Switch IGN 1. TURN. SEO IGN Fuses PARK LP Fuse #12 30A Park Lamp Relay. Healamp and Panel Dimmer Switch Park Lamps STOP LPS Fuse #14 20A VEH STOP and CHMSL Fuses. Trailer Wiring (LH.

Why are the front lights on my GMC Sierra not working?

2001 dually contractor bed front lights work properly rear light , stop lights hazard light signal lights , and parking lights doesn’t work, they gone, relay and fuses, relay and bulbs are good, how to fix them? 20 people found this helpful.

Why does my hazard light not work on my 1997 Chevy S10?

I have 1997 Chevy s10 brake light and hazard light won’t work. Turn Signal works and I change the turn signal switch and brake switch. I checked the ground around under bed. It looked good and I cleaned. So I was wander what else I could check.

What causes wheel rotation warning on Chevrolet Avalanche?

Anything the interferes with correct wheel rotation can trip this warning. Did you change tires, have brakes serviced or hit a pothole real hard? Believe it or not even a weak battery can cause warnings of this type due to voltage fluctuations. There are sensors in you wheels that monitor rotation speed, braking and position.

Where is the underhood fuse on a Chevrolet Avalanche?

The underhood fuse block is located near the battery on the driver’s side of the vehicle. Chevrolet Avalanche – fuse box diagram – engine compartment *1 — Gasoline Engine and Fuel Injection Rail #2. *2 — Gasoline Engine and Fuel Injection Rail #1. *3 — Gasoline Engine; Oxygen Sensors. *4 — Gasoline Engine; Oxygen Sensors. *5 — PCM Ignition Fuse

When do traction control lights appear on a Chevy truck?

Early to mid 2000’s Chevy trucks and suburbans have a common problem with the stabilitrak and traction control service lights appearing on the dash. For most truck owners, the warning lights occur frequently when the truck is idling and then disappears and reappears while driving.

What are the warning lights on a Chevrolet?

The following are warning lights and indicators found in vehicles built by Chevrolet. Click a link to learn more about each one. They are roughly ordered by importance, which tends to be by color (red, amber, yellow, orange, green, blue, gray). There are nearly 50 of them so search carefully!

Why are my tail lights not working on my Chevy C / K 1500?

Also, check your ground wire connections in the wiring harness as well. These problems can often result from the installation of after market trailer wiring harnesses where improper connections have allowed corrosion to enter the wire at the splice points. 30 people found this helpful. Check the ground Wire under the bed in the back.

Where are the brake lights on a C / K 1500?

There is a switch. I think on most C/K 1500/2500 it is on the brake pedal arm or the arm hits it. It is $5-$10; you might take ALL your truck data to the auto parts store, buy a new switch, then look for the same thing around the brake arm or under the hood. There’s a fuse. Find the fusebox and look for “brake”. The Owner’s Manual may have clues.

Where is the brake light switch on a Chevy Silverado?

The brake light switch is on the top of the brake pedal. Use a test light to see if you have power on both sides once the pedal is depressed (orange wire) Here are guides to help you get the job done. Here is a wiring diagram to help (below) Please let us know what you find. helpful?

What to do if your brake lights are not working?

Ok, changed out turn signal switch and still have no brake lights. Again, i changed the bulbs, replaced the brake switch, and replaced the turn signal switch. The parking lights work, the blinkers work, the back-up light works, and the hazzards work. But still no brake lights.

Why are the stoplights on my 1994 Chevy k1500 not working?

This 1994 Chevrolet K1500 pickup came in with the very unusual complaint that the stoplights would not work with the ignition on. I checked the brake light operation and sure enough the stoplights worked with the key off but as soon as the key was turned on they stopped.

Is the emergency brake light always on on a Chevy Silverado?

1988 chevy silverado The light on my dash for the e-brake is always on but the brake is not engaged. It has been like this since I bought the truck.

What kind of brake lights do GM cars have?

Description: Silverado, sierra. Power Adjustable Pedals. Without active brake control. Description: XT5. XT6. Acadia. Enclave. Traverse. Blazer. 3.6l. Blazer. 2.5l. Without e-boost. Brake pedal position sensor. Description: Verano. Description: Auto trans. Canyon, Colorado. Brake pedal position sensor.

Where is the brake light switch on a GMC Truck?

Brake Light Switch: How Do I Change My Brake Light Switch on My How do I change my brake light switch on my 1996 GMC 1500 series truck? have the same problem? The switch is located at the top of your brake pedal. You pretty much just have to unclip the old one and put the new one on.

Why do my brake lights not work on my GMC Sierra?

I have a 1994 GMC Sierra C1500 2WD with 4.3l w/automatic. It was a fleet vehicle. Plain Jane accept for High Output Heater, Limited Slip Diff and Engine Block Heater. Brake lights were working intermittently. Would come on when pedal as first depressed then go out after pedal traveled down a bit. I put in a new switch and all was well for 3 months.

Why are the brake lights on my Chevy 1500 not working?