Most popular

Why are my fuel gauges not working on my Chevy Silverado?

Table of Contents

Why are my fuel gauges not working on my Chevy Silverado?

In fact, this is,unfortunately, a common problem among most GM vehicles built from 2003-2006 – various gauges in the instrument clusters of these cars and trucks tend to fail as the mileage starts to get into the “high” zone. This problem is caused by defective drive motors that were used on the circuit boards of these instrument clusters.

What should I do if my gas gauge stops working?

Gas gauge, almost empty. Water temp, cold. No oil pressure. The alt wasn’t charging. No tac and no speedometer. The Lights work fine, The odometer is still rollin over, cruise control works, Gear selection indicator read out works fine.. Any ideas?

What to do if your speedometer stops working?

My speedometer hasn’t worked for probably 2 years. The dealer wanted over $500 to fix. I found the stepper motors on e-bay and purchased replacement lights as well. It takes a good soldering iron and a solder sucker tool you can buy at Radio Shack.

Are there Trans temp gauges on GM trucks?

If you were to get a Escalade Dash Cluster,which has the Transmission Temp gauge.The only item that needs to be done, is to have the Mileage programmed into the Escalade Cluster……the 99′ and up NBS Siverado’s/Sierra’s Were-n-Are Already Pre-Wired from the Factory for the Trans Temp Gauge.

Why are all the gauges on my GM Truck not working?

Last night I was comin home from the store and realized my speedometer wasn’t working (ins’t the first time) so i hit the dash, then realized NONE of the gauges were working.. Gas gauge, almost empty. Water temp, cold. No oil pressure. The alt wasn’t charging. No tac and no speedometer.

Why is the speedometer on my Chevy truck not working?

Inaccurate readings after changes to your Chevy: This is common with truck and SUV owners who change their wheels and tires, but can also happen if the wheel/tire combo is changed on a car. Larger combos, or those with different dimensions, will cause an inaccurate reading and the speedometer must be re-calibrated to regain accuracy.

Why is the odometer on my GM Truck not working?

A common fault on ’99 – ’02 GM trucks was the permanent or intermittent failing of the odometer/gear select LCD. This meant that you were unable to see what gear you were currently in, unable to determine the mileage of the vehicle, and unable to use the trip computer.

What happens when a speedometer sensor loses power?

Vehicle loses power Today’s cars and trucks have electronic fuel injection, which is controlled by the onboard computer. The EFI supplies fuel to the engine based on input from multiple sensors; one of which is the speedometer sensor.

What does it mean when your fuel gauge is full?

When this happens you’re left guessing how many miles you have left on your tank of fuel while your fuel level gauge bounces around from empty to ½ a tank to ¼ of a tank to full and back again. If this is the trouble you’re having, you’ll need to get your truck to a local mechanic for diagnosis and repair.

Where is the fuel level sensor on a Silverado?

If you were to send a tiny camera deep inside your fuel tank, you would find your fuel pump and fuel sending unit, swimming in fuel and quietly doing the jobs their names would suggest. Embedded among this happy apparatus, you would also find a fuel level sensor, which, also, would be doing the job its name suggests.

What’s the problem with the gas gauge on my Silverado?

Fuel gauge gives various readings at random times. Fuel gauge sensor has gone bad. My fuel Guage only works sporadically most of the time it shows empty with fuel light coming on. Haven’t fixed it yet but I will probably just install a new fuel pump…

Why does my Chevy Silverado say out of gas?

Chevrolet needs to do a recall of this issue. Just after the warranty expired the fuel gauge started acting up. When you fill the truck up with fuel it tells me I’m out of gas. Sometimes when I hit a bump the fuel gauge will seem to work briefly. It does seem to work properly as the fuel in the tank gets closer to empty.

Why does my fuel gauge go from empty to full?

FUEL LIGHT COMES ON AN FUEL GAGE GOES TO (E)WHEN TANK IS FULL,OR IDELING FOR LONG PIRED OF TIME,IF I PUT TRUCK IN (R)THEN BACK IN (P)PARK EVERYTHING WORKS LIKE IT SHOULD. Have the same problem the fuel gauge goes from empty to various readings.So frustrating. erratic fuel gauge.

What to do if your gas gauge fails to move?

If the float is OK and the float arm seems to be swinging freely through its full range, replace the tank unit. Ground the gas tank terminal post of the tank sending unit using a jumper wire. If the dash gauge now reeds empty, the gas tank unit is defective. If the dash gauge needle fails t move, the dash gauge is defective.

In fact, this is,unfortunately, a common problem among most GM vehicles built from 2003-2006 – various gauges in the instrument clusters of these cars and trucks tend to fail as the mileage starts to get into the “high” zone. This problem is caused by defective drive motors that were used on the circuit boards of these instrument clusters.

When this happens you’re left guessing how many miles you have left on your tank of fuel while your fuel level gauge bounces around from empty to ½ a tank to ¼ of a tank to full and back again. If this is the trouble you’re having, you’ll need to get your truck to a local mechanic for diagnosis and repair.

Where is the gas gauge located on a Chevy truck?

The gas gauge, often located in the instrument cluster, consists of two small coils spaced 90 degrees apart with an armature and a needle placed at the intersection of the two coils. A dampener is also located on the armature to prevent excessive needle movement on rough roads.

If you were to send a tiny camera deep inside your fuel tank, you would find your fuel pump and fuel sending unit, swimming in fuel and quietly doing the jobs their names would suggest. Embedded among this happy apparatus, you would also find a fuel level sensor, which, also, would be doing the job its name suggests.

Why does my gas tank gauge not move?

If the dash gauge now reeds empty, the gas tank unit is defective. If the dash gauge needle fails t move, the dash gauge is defective. If the gas gauge works, but reads lower than it should, check for defective wiring between the gas gauge and the tank sending unit.

What to do if your gas gauge reads lower than it should?

When the gauge reads lower than it should, check at the gauge by disconnecting the wiring from the tank unit. Turn the ignition on and if the needle reads full or above, the gauge unit is probably good and the tank unit or the wiring leading to it are probably the problem. Reconnect the tank unit wire to the gauge before proceeding.

Why does my 2005 LLY Duramax not start?

– Fixya Duramax won’t start! My 2005 LLY duramax became hard to start a few days ago. Then today it wouldn’t start at all. Turns over but wont start. The fuel filter primer loses pressure after priming it.

Can a Duramax engine crank but won’t start?

Drove home 5 miles. came out several hours later, engine cranks normally but won’t fire. Held throttle down and it started. Had slight surging. Very slight. Drove 5 miles, had dinner, came out, crank but no start. Held throttle down and still no start.

What causes a bad gas gauge on a Chevy truck?

A poor ground or loose connection to a gas gauge is just as likely to cause problems as loose or dirty battery cables assuredly will with your starting system.

Can a Duramax 6.6 start without a fuel pump?

My son has a 2011 duramax 6.6 that will not start on fuel but will start with a shot of either and runs like a top. He has replaced the fuel pump, … read more Vocational, Technical or Tra… Vocational, Technical or Tra… Vocational, Technical or Tra… I was low on fuel and drove to station to get more but never ran out.

Is there a site for a 2001 Chevy Silverado problem?

No one has added a helpful site for this 2001 Silverado problem yet. Be the first! Read reviews of repair shops in your area. Enter your zip code: I bought this 2001 Chevrolet z71 4×4 on Sep 10 2013.

Is there an odometer on my Chevy Silverado?

The security light flashes 5 time then the battery light will flash once. Then repeat. I have no odometer lit at all. The shift position out as well. I put a used cluster panel in from the auto salvage yard. I did get a odometer and shift position to come on, but still no gauges. So I didn’t buy it.

What to do if your Chevy Silverado has a problem?

Do the right thing, fix the problem in a recall and thank all your customers so that they may continue to fund your retirement.

What to do if your fuel gauge is stuck on empty?

Fuel gauge stuck on empty? Two ways to fix that- scrape up some cash and put gas in it, or if that doesn’t work, replace the fuel level sensor in the tank. Altogether, it took about 5 hours and $75. None of the auto parts stores had this sensor in stock, so it was an overnight wait for that.

The security light flashes 5 time then the battery light will flash once. Then repeat. I have no odometer lit at all. The shift position out as well. I put a used cluster panel in from the auto salvage yard. I did get a odometer and shift position to come on, but still no gauges. So I didn’t buy it.

The gas gauge, often located in the instrument cluster, consists of two small coils spaced 90 degrees apart with an armature and a needle placed at the intersection of the two coils. A dampener is also located on the armature to prevent excessive needle movement on rough roads.

How many miles does a 2002 1500HD 4×4 get?

I purchased a 2002 1500HD 4X4 in July of this year. I got 7MPG with the first two tanks of gas. I returned it to the Dealer for service. They found a calibration fault in the computer. After fixing the fault I got 10MPH (city). I took it back to the dealer and was told nothing could be done until it had about 3000 miles on it. OK.

Why is the fuel gauge on my Chevy truck not working?

The most common problem with the fuel gauge reported by Chevy truck owners is a complete failure to register the fuel level. The fuel gauge sits on empty, even after you’ve just filled up the tank.

What kind of engine does a Chevy 6.0 have?

Under the hood of 2007-2009 Chevy and GMC 6.0-liter V8 equipped vehicles, you’ll find the LY6 engine. It has a power output of 363 horsepower and 383 pound-feet of torque and is found in the following vehicles: Active Fuel Management intends to increase fuel economy.

When did the GM 6.0 liter V8 end?

Another variant of the gen-three GM 6.0-liter V8 is the LQ9, known as the Vortec 6000 HO or VortecMAX. It is a high output version of the LQ4 that uses a higher compression ratio to boost the horsepower output. It was only available in a handful of models and first became available in 2002. The production of the LQ9 ended in 2007 like the LQ4.

What to do if your fuel gauge is full?

If you DO have 12 volts to the fuel gauge, the next step is to remove the fuel sending unit wire, and, with the ignition key “on”, ground the sender wire to a good chassis ground. The fuel gauge should immediately go to empty. Removing the sending unit wire from the chassis ground the fuel gauge should go directly to “full”.

Why does my fuel gauge read way over full?

Whether the truck is on or not the dash fuel gauge will read way over above full, when there is actually no fuel or barely any fuel in the tank at all. The problem is usually said to be bad ground wiring or the floater system inside the tank is messed up, in this video I go through how I fixed my issue, which was a bad floater system.

When the gauge reads lower than it should, check at the gauge by disconnecting the wiring from the tank unit. Turn the ignition on and if the needle reads full or above, the gauge unit is probably good and the tank unit or the wiring leading to it are probably the problem. Reconnect the tank unit wire to the gauge before proceeding.

What to do if your gas gauge is on empty?

For example, if the gas gauge needle remains on empty when the ignition key is turned to the “on” position and you are sure the gas tank is partially full, battery current may not be reaching the gauge. To check further, connect a jumper wire between the ignition switch and the dash gauge.

How much does it cost to replace a gas pump on a Chevy Silverado?

The average cost for a Chevrolet Silverado 1500 Fuel Pump Replacement is between $1,132 -$1,182. Learn More Gas gauge reading empty. Just replaced fuel level sensor and still doing the same. Dont know what else to do Fuel sensor gauge never reads correctly. It continuously jumps between full and empty while I’m driving or while I’m at a light.

Why does my gas gauge keep showing empty?

Check the fuel pump ground, it’s a PITA, maybe you can see it with a mirror and flash light. A poor ground here will cause weird fuel gauge readings. Buddy use to have this problem on an old truck of his. He just bounced the gas pedal a few times and it always corrected itself, well at least until it did it again.

Why does the low fuel light come on when the tank is full?

All the sudden, the Low Fuel light comes on and the gas gauge is showing empty. I know this is wrong because I just filled up two days ago and have hardly gone anywhere.

What are the warning lights on a Chevrolet?

The following are warning lights and indicators found in vehicles built by Chevrolet. Click a link to learn more about each one. They are roughly ordered by importance, which tends to be by color (red, amber, yellow, orange, green, blue, gray). There are nearly 50 of them so search carefully!

Why is the gas gauge on my Silverado not working?

Fuel gauge is not reading the proper level of Diesel fuel in the tank. The fuel gauge has been erratic for the last 50000 miles. It tells me the fuel level for a short period and then goes to reading empty.

Why is the gas gauge showing empty at a red light?

So I was sitting at a red light this afternoon with my foot on the brake. All the sudden, the Low Fuel light comes on and the gas gauge is showing empty. I know this is wrong because I just filled up two days ago and have hardly gone anywhere.

All the sudden, the Low Fuel light comes on and the gas gauge is showing empty. I know this is wrong because I just filled up two days ago and have hardly gone anywhere.

What does the gas gauge read on a Chevy Silverado?

The Fuel Gauge is reading only 1/4 full after a fill up and the mileage range is only 110 miles. The Mileage Range begins to read as Low even with the tank still holding over 10 gallons. I recently had the duel filter housing assembly replaced as the truck would not start.

What’s the gas mileage on a Chevy Silverado?

I may be naive but I expect when you pay soo much for a product it should work! I own a 2500 HD Duramax Diesel, and it is now approaching 175K miles. The Fuel Gauge is reading only 1/4 full after a fill up and the mileage range is only 110 miles. The Mileage Range begins to read as Low even with the tank still holding over 10 gallons.

What to do if your fuel gauge is bad?

Fuel gauge troubleshooting begins with isolating the problem either to the gauge, sending unit, fuse or wiring. The most common gauge problems are either a bad ground at the tank, or a sender problem. As with any electrical troubleshooting, it is best to check the fuse and all wiring connections are clean, tight and free of corrosion.

Where is the fuel gauge sender located in a car?

The fuel gauge sender is a component that is found in the gas tank of most road going vehicles. The fuel gauge sender, also commonly referred to as the fuel sending unit, is the component responsible for sending the signal that operates the fuel level gauge in the instrument cluster.

How does a fuel pump work on a gas gauge?

The fuel pump module includes the fuel sending unit, used by the gas gauge to detect and display fuel level. https://www.flickr.com/photos/3ndymion/33556245572. The gas gauge is a relatively simple circuit, but its simplicity means each component is essential to its function.

The fuel pump module includes the fuel sending unit, used by the gas gauge to detect and display fuel level. https://www.flickr.com/photos/3ndymion/33556245572. The gas gauge is a relatively simple circuit, but its simplicity means each component is essential to its function.

What causes a fuel gauge to read empty?

Another common symptom of a faulty fuel gauge sender is a gauge that is stuck on empty. If the float somehow breaks or becomes separated from the arm it may cause the fuel gauge to malfunction and become stuck on empty. A faulty resistor can also cause the gauge to read empty. 3. Fuel gauge stuck on full

When do you need to replace the fuel gauge sender?

If your fuel gauge behaves erratically or is stuck on full or empty, you may need to replace the fuel gauge sender. 1. Fuel gauge behaves erratically 2. Fuel gauge stuck on empty 3. Fuel gauge stuck on full The fuel gauge sender is a component that is found in the gas tank of most road going vehicles.

What would cause a fuel gauge to peg way past full?

Re: What would cause a fuel gauge to peg way past full? Generally, if your gauge is reading past full and the tank isn’t full, it’s the positive wire that has a connection problem. If it’s reading totally empty, it’s the ground. If your tank if full of gas right now; I’d drive it for a while and see what happens.

Why does my gas gauge read full or above?

If the gauge reads full or above with the wire disconnected, the problem is in the tank unit rather than the wiring. It could be an electrical fault, or the float may be stuck or may have sunk because of a hole caused by corrosion. Remove the tank sending unit and check it.

Whether the truck is on or not the dash fuel gauge will read way over above full, when there is actually no fuel or barely any fuel in the tank at all. The problem is usually said to be bad ground wiring or the floater system inside the tank is messed up, in this video I go through how I fixed my issue, which was a bad floater system.

What should I do if my gas gauge is not working?

If necessary, clean the connection and reinstall the wire to the terminal, then check the gauge operation. If that didn’t fix the problem, use a jumper wire to ground the electrical terminal on the tank sending unit to the tank unit housing (leave the wire to the gauge connected to the tank unit).

What are the parts of a gas gauge?

The gas gauge system can be broken down into three basic parts: gauge, sender, and circuit. A fault in one or more of these parts will lead to gas gauge failure. The sending unit is usually part of the Fuel Pump Module : a combination of parts that includes the fuel pump, fuel strainer, fuel filter, and fuel float.

If necessary, clean the connection and reinstall the wire to the terminal, then check the gauge operation. If that didn’t fix the problem, use a jumper wire to ground the electrical terminal on the tank sending unit to the tank unit housing (leave the wire to the gauge connected to the tank unit).

Why does my gas gauge read high when the tank is full?

A functioning sending unit will have a high resistance when the tank is full and a low resistance when the tank is empty. If the gauge reads higher than it should, make sure the wire attached to the electrical terminal on the tank sending unit is making a good ground connection.

Why is my speedometer stuck on my GM Silverado?

This section will outline all the most common problems that have been identified. The most common instrument cluster problem seen on the 03-06 GMs is faulty analog gauges. This is usually the first gauge problem the vehicle owner sees and is experienced as a stuck, sticky or jumpy gauge needle.

Why are my dash gauges flickering in my Silverado Sierra?

Yah, it is the common problem with 2003-2006 trucks. The instrument clusters are bad in them. There are a bunch of outfits that will refurbish and warrant them for a little over $100. I would contact them with your symptoms and let them (or another outfit) tell you if they can help you out.

When did my Chevy Silverado cluster gauges go haywire?

I bought this 2001 Chevrolet z71 4×4 on Sep 10 2013. I got a good deal on it if I can fix the problem. All the gauges are dead, no function. The security light flashes 5 time then the battery light will flash once. Then repeat. I have no odometer lit at all.

Why does the check gauge light come on?

Gauges that usually make up the panel watch the amount of oil, gas and battery power, in addition to the engine. When you notice the Check Gauge light is on don’t panic.

Yah, it is the common problem with 2003-2006 trucks. The instrument clusters are bad in them. There are a bunch of outfits that will refurbish and warrant them for a little over $100. I would contact them with your symptoms and let them (or another outfit) tell you if they can help you out.

What does it mean when gauges in your car stop working?

But when the gauges in your car stop working, it’s not a situation you can safely ignore. When one gauge stops working, the problem may be in the gauge itself or a bad sensor, while all the gauges cutting out at the same time often indicates a blown fuse or a defective instrument cluster.

Where is the check gauge on a car?

The Check Gauge light is located on the dashboard. This area is also known as the instrument panel. How the dashboard looks and what gauges are included will vary by the type and brand of vehicle you are driving. Gauges that usually make up the panel watch the amount of oil, gas and battery power, in addition to the engine.

Why did my instrument cluster quit working on my 2003 Silverado?

I have a 2003 GMC Serria 1500HD 4WD that the gauges quit working today from the Tach, gas, oil, temp and etc. How can this be fixed? Thanks … read more MY 2003 Silverado XT instrument gauges didn’t work anymore after getting gas. I’ve checked fuses. Everything else seems to be working fine. … read more

Are there any problems with the GM gauge clusters?

The next most common problem seen on GM instrument clusters are failing digital displays. This problem is unrelated to the stepper motor problem but is often seen in the same clusters. Most GM gauge clusters of this time frame have two digital displays – the odometer and the gear indicator (commonly called the PRNDL screen).

This section will outline all the most common problems that have been identified. The most common instrument cluster problem seen on the 03-06 GMs is faulty analog gauges. This is usually the first gauge problem the vehicle owner sees and is experienced as a stuck, sticky or jumpy gauge needle.

What are the symptoms of a bad fuel gauge sender?

Usually a bad or failing fuel gauge sender will produce a few symptoms that can alert the driver of a potential issue. 1. Fuel gauge behaves erratically One of the first symptoms of a problem with the fuel gauge sender is a fuel gauge that behaves erratically.

The next most common problem seen on GM instrument clusters are failing digital displays. This problem is unrelated to the stepper motor problem but is often seen in the same clusters. Most GM gauge clusters of this time frame have two digital displays – the odometer and the gear indicator (commonly called the PRNDL screen).

Note that some self-test steps may stop the gas gauge at 1/4, 1/2, and 3/4, as well. Fuel sender test. The fuel sender test should be conducted when the tank is lower than HALF, to prevent fuel splashing. Start by making sure the plug is clean, dry, and free of corrosion. Make sure the pins are straight and that the connector is fully seated.

A functioning sending unit will have a high resistance when the tank is full and a low resistance when the tank is empty. If the gauge reads higher than it should, make sure the wire attached to the electrical terminal on the tank sending unit is making a good ground connection.

Why does my 2003 Chevy Silverado not start?

My 2003 Silverado has issues starting sometimes. If I hit the steering column it will sometimes start. My silverado has left me stranded numerous times with this intermittent starting bullsh!t. The truck starts majority of the time however sometimes I go to start the engine and nothing!!

How does the fuel gauge work in a car?

The fuel gauge in your automobile indicates the amount of fuel that remains in the gas tank. Some fuel gauges have an analog display while others have a digital or liquid crystal display. Electronic and software malfunctions may cause the fuel gauge in your automobile to inaccurately measure or display the amount of fuel remaining in the gas tank.

What causes the gas gauge needle to move?

The variations in the amount of fuel in the tank cause the arm to move. This changes the resistance of the tank unit, changing the amount of current at the gauge unit coils, which in turn moves the needle located between the coils.

How does the fuel gauge work on a Chevy Silverado?

The low fuel light came on and the fuel gauge read empty right after I filled the tank. Then, very slowly, the needle on the fuel gauge started to rise, and after about 15 minutes of driving was finally registering what seemed to be the correct amount.

What causes the fuel gauge to go empty?

If truck is stationary for several seconds fuel gauge will display empty even though it is not. Not a major problem but definitely a symptom.

What is the ZIP code for a 2001 Chevy Z71 4×4?

Enter your zip code: I bought this 2001 Chevrolet z71 4×4 on Sep 10 2013. I got a good deal on it if I can fix the problem. All the gauges are dead, no function. The security light flashes 5 time then the battery light will flash once. Then repeat. I have no odometer lit at all. The shift position out as well.

The variations in the amount of fuel in the tank cause the arm to move. This changes the resistance of the tank unit, changing the amount of current at the gauge unit coils, which in turn moves the needle located between the coils.

Why does my GM fuel gauge keep twitching?

The stepper motor that controls that gauge has gone bad. GM apparently had quite a number of instrument clusters where one or more gauges either failed or went just plain nuts.

Fuel gauge stuck on empty? Two ways to fix that- scrape up some cash and put gas in it, or if that doesn’t work, replace the fuel level sensor in the tank. Altogether, it took about 5 hours and $75. None of the auto parts stores had this sensor in stock, so it was an overnight wait for that.

What does it mean when your fuel gauge is low?

When we actually first got in it the fuel was very low and the gauge actually started low then slowly rose up to full after a few slow minutes, kicked back down and then was all over the map. Once we topped off the fuel the gauge started with the vibrating.

The stepper motor that controls that gauge has gone bad. GM apparently had quite a number of instrument clusters where one or more gauges either failed or went just plain nuts.

When we actually first got in it the fuel was very low and the gauge actually started low then slowly rose up to full after a few slow minutes, kicked back down and then was all over the map. Once we topped off the fuel the gauge started with the vibrating.

What happens if you reset your fuel gauge?

Electronic and software malfunctions may cause the fuel gauge in your automobile to inaccurately measure or display the amount of fuel remaining in the gas tank. If this happens, reset your fuel gauge. Each make and model of car has its own specific instructions on how to reset the fuel gauge, but the process is basically the same. Step 1

Electronic and software malfunctions may cause the fuel gauge in your automobile to inaccurately measure or display the amount of fuel remaining in the gas tank. If this happens, reset your fuel gauge. Each make and model of car has its own specific instructions on how to reset the fuel gauge, but the process is basically the same. Step 1

If the dash gauge now reeds empty, the gas tank unit is defective. If the dash gauge needle fails t move, the dash gauge is defective. If the gas gauge works, but reads lower than it should, check for defective wiring between the gas gauge and the tank sending unit.

What’s the low fuel light on my Duramax?

My ’01 2500HD Duramax’s fuel gauge has been acting strange and for the most part doesn’t work at all. Most of the time my gauge reads empty and the “Low Fuel” light stays on.

Why is my Chevy 2500HD oil gauge not working?

04 2500 HD DURAMAX DASH PROBLEMS. Tach works for awhile then stops altogether, will work when I drive the next time. Know my oil gauge is acting up. Checked with GM dealer, they informed me that the warranty on the dash ran out at 70,000mi. (85000) when my problems started. Whole panel has to be replaced. 04 2500 HD DURAMAX DASH PROBLEMS.

My ’01 2500HD Duramax’s fuel gauge has been acting strange and for the most part doesn’t work at all. Most of the time my gauge reads empty and the “Low Fuel” light stays on.

04 2500 HD DURAMAX DASH PROBLEMS. Tach works for awhile then stops altogether, will work when I drive the next time. Know my oil gauge is acting up. Checked with GM dealer, they informed me that the warranty on the dash ran out at 70,000mi. (85000) when my problems started. Whole panel has to be replaced. 04 2500 HD DURAMAX DASH PROBLEMS.

Why does my Chevy Silverado have a gas low warning light?

When ignition is turned off and engine restarted the fuel low warning light always comes on and the guage reads empty and slowly rises (it takes about 10 minutes) to what I assume is the correct fuel level. Giving false reading. Fuel Gauge level reads incorrect. Fuel gauge gives various readings at random times. Fuel gauge sensor has gone bad.

Why does fuel gauge read wrong after fuel pump replaced?

Fuel gauge reads wrong after fuel pump replaced – YouTube If you have a 96 or 97 year gm truck that needs a fuel pump, be sure to order it by the VIN. There is an option for a anti-slosh module that could cause you If you have a 96 or 97 year gm truck that needs a fuel pump, be sure to order it by the VIN.

Why does my gas gauge go low when I stop?

When I stop the gauge goes to empty and the low fuel light comes on. After driving several miles, it will correct itself but the same thing happens when I stop. Dealer says it could be two different things causing the problems and each one is $500 to fix each one. Other people I know have the same problem.

Why is my fuel gauge not working properly?

Fuel gauge troubleshooting begins with isolating the problem either to the gauge, sending unit, fuse or wiring. The most common gauge problems are either a bad ground at the tank, or a sender problem.

What should I do if my fuel gauge is stuck?

If the gauge gives you a full reading, the sending unit is faulty and should be replaced. Verify that all of the wiring is securely connected to the back of the fuel gauge, which will require you to remove the dashboard to gain access to the instrument cluster.

What happens to the speedometer on a Chevy Silverado?

Has the speedometer on your Chevy Silverado stopped telling you your actual speed? Does it get to zero and get stuck, then suddenly tell you you’re going 80 when you know you’re only going 20?

Has the speedometer on your Chevy Silverado stopped telling you your actual speed? Does it get to zero and get stuck, then suddenly tell you you’re going 80 when you know you’re only going 20?

Why does my gas gauge keep pegging full?

The gas gauge might interpret voltage feedback from a dead sender as FULL or EMPTY, consequently pegging the gauge no matter the actual fuel level. Circuit Problems can cause the gas gauge to stop functioning normally.

Why is the gas gauge not working right?

Why is the Gas Gauge in My Chevy Truck Not Working Right? 1 Known Problems. The most common problem with the fuel gauge reported by Chevy truck owners is a complete failure to register the fuel level. 2 Causes. Over time, gasoline corrodes the fuel gauge sensor. 3 Solution. Disconnect the battery for 10 to 15 minutes. …

Why is my speedometer not working on my Silverado?

Speedometer not functioning properly, diesel gauge and radio not functioning properly also. The gauge problems are pretty common on the 03-06 Silverados, it’s caused by failing gauge motors inside the instrument cluster. Check this page for more on how to get it fixed – Silverado Instrument Cluster Repair

Why does my Chev Silverado have no tach?

2003 Chev Silverado. All instrument cluster gauges quit today. No speedo, tach, fuel ,temp, oil etc. Never any problem 2003 chevy: All instrument cluster gauges quit today..speedo..tach… My oil pressure, fuel, coolant temp, and battery voltage gauge don’t work. My Speedo and tach work fine. I also have a battery and abs light on.

Speedometer not functioning properly, diesel gauge and radio not functioning properly also. The gauge problems are pretty common on the 03-06 Silverados, it’s caused by failing gauge motors inside the instrument cluster. Check this page for more on how to get it fixed – Silverado Instrument Cluster Repair

If you were to get a Escalade Dash Cluster,which has the Transmission Temp gauge.The only item that needs to be done, is to have the Mileage programmed into the Escalade Cluster……the 99′ and up NBS Siverado’s/Sierra’s Were-n-Are Already Pre-Wired from the Factory for the Trans Temp Gauge.

What do I do if my gas gauge is not working?

In most cases, to gain access to the fuel tank sending unit mount / fuel pump mounting hole, you’ll need to drop the gas tank down. Be sure to do this when there is either minimal gas in the vehicle, or it’s been siphoned out.

Where is the fuel level sender on a car?

The fuel level sender on this vehicle is connected to the fuel pump module that goes in the fuel tank. When you were installing the fuel pump module back into the fuel tank you may have inadvertently bent or damaged the the fuel gauge sending unit.

In most cases, to gain access to the fuel tank sending unit mount / fuel pump mounting hole, you’ll need to drop the gas tank down. Be sure to do this when there is either minimal gas in the vehicle, or it’s been siphoned out.

The fuel level sender on this vehicle is connected to the fuel pump module that goes in the fuel tank. When you were installing the fuel pump module back into the fuel tank you may have inadvertently bent or damaged the the fuel gauge sending unit.

Why is the fuel gauge on my car not working?

Some fuel gauges have an analog display while others have a digital or liquid crystal display. Electronic and software malfunctions may cause the fuel gauge in your automobile to inaccurately measure or display the amount of fuel remaining in the gas tank. If this happens, reset your fuel gauge.

Why is my Duramax diesel engine not working?

The trucks computer keeps track of how much fuel needs to be added or subtracted from each individual cylinder to make the engine run smoothly, and this value is called the balance rate. If one cylinder is contributing too much or not as much as the rest, the cause is usually a bad injector and the cure is a replacement.

What was the code name for the Duramax in 2011?

In an effort to keep up with the ever-tightening emission regulations, GM redesigned its Duramax for the 2011 model year, and this time the code name was LML.

What happens if the speedometer on my Chevy Silverado fails?

If the speedometer failed and the vehicle is within 7 years had less than 70,000 miles on it, upon proper proof of claim GM will reimburse the cost of repairs (parts and labor) up to the limit of what a GM dealership would have charged.

What kind of display does a GM speedometer have?

Most GM gauge clusters of this time frame have two digital displays – the odometer and the gear indicator (commonly called the PRNDL screen). Either one or both screen will typically be affected. This common issue is not actually a problem with the digital displays themselves as they seem to be quite reliable. 1. Dim, Dark or Dead Display

What causes a bad gauge cluster in a Chevy Silverado?

Individual gauge problems are almost universally caused by failing gauge motors. Each gauge is controlled by one gauge motor called a stepper motor. For example, an instrument cluster with 6 analog gauges will have 6 stepper motors.

If the speedometer failed and the vehicle is within 7 years had less than 70,000 miles on it, upon proper proof of claim GM will reimburse the cost of repairs (parts and labor) up to the limit of what a GM dealership would have charged.

Most GM gauge clusters of this time frame have two digital displays – the odometer and the gear indicator (commonly called the PRNDL screen). Either one or both screen will typically be affected. This common issue is not actually a problem with the digital displays themselves as they seem to be quite reliable. 1. Dim, Dark or Dead Display

Fuel gauge troubleshooting begins with isolating the problem either to the gauge, sending unit, fuse or wiring. The most common gauge problems are either a bad ground at the tank, or a sender problem. As with any electrical troubleshooting, it is best to check the fuse and all wiring connections are clean, tight and free of corrosion.

If the float is OK and the float arm seems to be swinging freely through its full range, replace the tank unit. Ground the gas tank terminal post of the tank sending unit using a jumper wire. If the dash gauge now reeds empty, the gas tank unit is defective. If the dash gauge needle fails t move, the dash gauge is defective.

Re: What would cause a fuel gauge to peg way past full? Generally, if your gauge is reading past full and the tank isn’t full, it’s the positive wire that has a connection problem. If it’s reading totally empty, it’s the ground. If your tank if full of gas right now; I’d drive it for a while and see what happens.

The fuel gauge sender is a component that is found in the gas tank of most road going vehicles. The fuel gauge sender, also commonly referred to as the fuel sending unit, is the component responsible for sending the signal that operates the fuel level gauge in the instrument cluster.

What is the sending unit on a fuel pump?

The fuel gauge sender, also commonly referred to as the fuel sending unit, is the component responsible for sending the signal that operates the fuel level gauge in the instrument cluster. The fuel sending unit is made up of an arm, float, and a resistor that changes according the position of the float.

What should fuel gauge read if tank is full?

Take an ohmmeter and see what the resitance is between ground wire and the purple wire. If the tank is empty, it should read around 0, if it’s full, about 90 ohms. If that’s right, then check the wiring going to the gauge for excessive resistance.

Why are my dash gauges not working on my 2002 Chevy 2500HD?

I have a 2002 chevy 2500hd 4×4 my fuel,trans temp,and engine temp,gear select and message center flashes what is the problem it happens and stops and starts up again went almost a year and started again You can’t post conmments that contain an email address.

Why is the message center not working on my 2003 Silverado?

An expert who has achieved level 1. An expert that has 1 follower. I have a 2003 silverado 2500hd and sometimes when I start the truck the message center won’t come on but if drive it about five miles and shut the truck off and start it again it will come on You can’t post conmments that contain an email address.

Why does my 2003 Silverado HD engine get hot?

Why does my 2003 Silverado HD engine get hot when i’m backing up,even a small load on my trailer All I know about my truck is that it is a 2500 HD The engine gets hot when I’m backing up with a load, or even an empty trailer. sudden loss of power duramax 6.6 ?

Why does my gauge quit working on my Chevy Silverado?

20″ of a cooper braided ground wire on the drivers rear side came out on a chunk of snow that I kicked off. My voltage meter quit working today … read more Auto repair pro, 30 years ex… Hi, I have a 1999 chevy silverado with gauge problems. I see it’s a common problem, but my problem may be the result of a parasitic draw, … read more

2003 Chev Silverado. All instrument cluster gauges quit today. No speedo, tach, fuel ,temp, oil etc. Never any problem 2003 chevy: All instrument cluster gauges quit today..speedo..tach… My oil pressure, fuel, coolant temp, and battery voltage gauge don’t work. My Speedo and tach work fine. I also have a battery and abs light on.

I have a 2003 GMC Serria 1500HD 4WD that the gauges quit working today from the Tach, gas, oil, temp and etc. How can this be fixed? Thanks … read more MY 2003 Silverado XT instrument gauges didn’t work anymore after getting gas. I’ve checked fuses. Everything else seems to be working fine. … read more

What to do if your fuel gauge stops working?

If your fuel gauge has stopped working and another gauge in your instrument cluster has stopped working, then you would probably be best off just having your instrument cluster rebuilt. This is the less expensive of the repairs and something you are likely to have to do eventually anyway.

If the gauge gives you a full reading, the sending unit is faulty and should be replaced. Verify that all of the wiring is securely connected to the back of the fuel gauge, which will require you to remove the dashboard to gain access to the instrument cluster.

Why are all the gauges on my car not working?

Each gauge has a motor that controls it’s needle movement and when the motor goes out the gauge will either stick, jump around or die all together. Another common problem is when all the gauges just stop working all at once like yours (but the back lights inside the instrument cluster still work).

Why is the Gas Gauge in My Chevy Truck Not Working Right? 1 Known Problems. The most common problem with the fuel gauge reported by Chevy truck owners is a complete failure to register the fuel level. 2 Causes. Over time, gasoline corrodes the fuel gauge sensor. 3 Solution. Disconnect the battery for 10 to 15 minutes.

What does the fuel gauge on a Ford tell you?

Fuel Gauge: The fuel gauge indicates the amount of fuel left in the car and how far it is from an empty tank or a full tank. Tachometer: This describes the rotation rate of the crankshaft in the engine. Odometer: This tells you nothing but how many miles or kilometers the car has traveled depending on what system the region uses.

How to troubleshoot a tractor fuel gauge that still runs?

Put one of the ohmmeter’s leads on the negative terminal and the other on a good ground. There should be no resistance. If there is resistance, repair the ground. Check for power at the sending unit. There should be 12 volts. Check the ground to the frame for resistance with the ohmmeter.

Can a bad fuel gauge sender send a bad signal?

Another, less common, symptom of an issue with the fuel gauge sender is a fuel gauge that is stuck on full. A faulty fuel gauge resistor can send a bad signal to the instrument cluster which can cause the gauge to permanently read full. This is an issue, as the driver needs to know the accurate fuel level of the vehicle as to not run out of fuel.

What can be the cause of my temp gauge not working?

What could be the cause of my temp gauge not working? My temp gauge is not working. Where are some good areas to look for the problem.

What to do if your fuel gauge is not working?

Check the grounding wire on the fuel gauge. To do so, connect the negative jumper cable to the vehicle’s frame and the positive cable to the fuel gauge’s grounding terminal. Turn the ignition to the on position and look at the fuel gauge. If the gauge is not working, then the grounding wire needs to be replaced.

Where is the temp gauge on my car?

If it does the sensor is bad. If it does not the guage is bad. The temp gauge sensor for your engine is located down front on the engine block near the thermostat housing & hose.

Why does my car gauge read cold when I Turn on the ignition?

With the ignition on, the gauge should register cold. If you connect the sending unit wire to ground, the gauge should switch to read hot. If the gauge moves as expected, then you can suspect a bad sending unit. If the gauge doesn’t move when you ground out the sensor wire, then you can suspect a bad gauge.

The gas gauge might interpret voltage feedback from a dead sender as FULL or EMPTY, consequently pegging the gauge no matter the actual fuel level. Circuit Problems can cause the gas gauge to stop functioning normally.

What’s the fuel gauge on a Dodge truck?

Well today on the way to work, I had about 1/2 of 1/4 tank. I stop and put $25 in it and when I go to start the truck, the fuel gauge read empty. On the way home from work, I throw in another $20 and the gauge still doesent move….. Truck had no check engine lights or anything.. it runs normal…..

Is there a problem with my fuel gauge?

It wasnt the problem. gage still does same thing. i put about 14 gallons or so and i only am reading a quarter of a tank and the tank is 20 or so gallons on the front. i took the fuse block apart under the hood. it just snaps out. nothing is wrong. This truck is a piece of shit Same here mine just started doing this.Can you post some pics please?

What is the Dorman number on the fuel gauge?

Today I replaced the electrical connector for the fuel sending unit at the rear tank and it solved the problem. The Dorman part number is 645-668. I hope this information can be helpful to those dealing with this annoying gauge issue.

How to fix fuel gauge on GMC Duramax?

Cut the tie and pull the wires from the harness and inspect for cuts and wear. The sharp corner of the FICM bracket where it is tied down to, cuts into the wires. Repair and insulate the harness with a short piece of heater hose.

What should I do if my fuel pump does not work?

After mechanic replaced… After mechanic replaced fuel pump gas gauge does not work. Took my truck to mechanic for routine maintenance and he replaced the fuel pump. After I got the truck back and filled the gas tank I noticed the fuel gauge wasn’t reading correctly.

After mechanic replaced… After mechanic replaced fuel pump gas gauge does not work. Took my truck to mechanic for routine maintenance and he replaced the fuel pump. After I got the truck back and filled the gas tank I noticed the fuel gauge wasn’t reading correctly.

Why is my oil pressure gauge not working?

The gauge problems are pretty common on the 03-06 Silverados, it’s caused by failing gauge motors inside the instrument cluster. Check this page for more on how to get it fixed – Silverado Instrument Cluster Repair I have a 2003 Chevrolet 1500 HD+ 4×4 6.0 gas motor. The oil pressure gauge either reads 80psi or 0 psi.

What to do if your GMC Sierra Voltage Gauge does not work?

GM has had a issue with the clusters in the 2003-2005 trucks. The cluster will be replaced for free for your truck if it has less then 70k miles. I would take it to your local dealer and tell them that the voltage gauge sticks at times. They should order one for you, takes 1-2 days and replace it for you at no charge.

Why is the fuel gauge on my 2003 Silverado not working?

2003 Silverado 1500 Instument gauges inoperative. Dash lights up, but cant’t tell how much speed or rpm range and fuel level. Sounds like your gauge drive motors are wearing out. It requires motor replacement inside the instrument cluster. 2003 chevy silverado, fuel gauge started registere…

The gauge problems are pretty common on the 03-06 Silverados, it’s caused by failing gauge motors inside the instrument cluster. Check this page for more on how to get it fixed – Silverado Instrument Cluster Repair I have a 2003 Chevrolet 1500 HD+ 4×4 6.0 gas motor. The oil pressure gauge either reads 80psi or 0 psi.

GM has had a issue with the clusters in the 2003-2005 trucks. The cluster will be replaced for free for your truck if it has less then 70k miles. I would take it to your local dealer and tell them that the voltage gauge sticks at times. They should order one for you, takes 1-2 days and replace it for you at no charge.

Why are the cluster gauges going out on my GMC?

Sounds like the cluster gauges are beginning to crap on you. Common problem on the 02 to 04 trucks. Time to get the new updated style which has the corrected problem on the cluster gauge. This is was a factory recall and is covered by GM, both my dads and mine went out and were replaced for free, take it in.

Why are the gauges on my car not working?

For the past few months I have had issues with the instrument panel gauges. While driving all of the gauges (speedometer, gas, voltage, fluid, etc.) simultaneously fail. Once this happens all of the indicator lights will flash on then go off and the gauges will come back to their proper level.

Sounds like the cluster gauges are beginning to crap on you. Common problem on the 02 to 04 trucks. Time to get the new updated style which has the corrected problem on the cluster gauge. This is was a factory recall and is covered by GM, both my dads and mine went out and were replaced for free, take it in.

For the past few months I have had issues with the instrument panel gauges. While driving all of the gauges (speedometer, gas, voltage, fluid, etc.) simultaneously fail. Once this happens all of the indicator lights will flash on then go off and the gauges will come back to their proper level.

What should I do if my gas gauge reads Full?

Turn the ignition on and if the needle reads full or above, the gauge unit is probably good and the tank unit or the wiring leading to it are probably the problem. Reconnect the tank unit wire to the gauge before proceeding. The next trouble-shooting task begins by disconnecting the wire to the tank sending unit.

What does the pink wire on a fuel gauge mean?

The last wire that runs to the gauge is the sending wire that originates from the fuel sender. This wire is normally (or should be) pink in most vessels. This informs the gauge of the position of the fuel sender. The only missing component left on these gauges is usually the light.

Why is my gas gauge no longer working?

When you were installing the fuel pump module back into the fuel tank you may have inadvertently bent or damaged the the fuel gauge sending unit. If the sending unit arm got bent when installing it then it will bind up on the metal anti slosh plates inside the fuel tank.

Is the fuel gauge still working after replacing the sender?

Even after replacing sender – 2008 Tahoe – 1999-2013 Silverado & Sierra 1500 – GM-Trucks.com Sign up for FREE! Become a GM-Trucks.com Member Today!

Why does my car’s fuel gauge keep resetting?

Electronic and software malfunctions may cause the fuel gauge in your automobile to inaccurately measure or display the amount of fuel remaining in the gas tank. If this happens, reset your fuel gauge. Each make and model of car has its own specific instructions on how to reset the fuel gauge, but the process is basically the same.

What does it mean when your gas gauge reads empty?

Once this starts to get worse, there will be portions of the fingers that are barely touching and others that are kind of flopping on and off the board. This will send the crazy signal to the fuel gauge.

For example, if the gas gauge needle remains on empty when the ignition key is turned to the “on” position and you are sure the gas tank is partially full, battery current may not be reaching the gauge. To check further, connect a jumper wire between the ignition switch and the dash gauge.

Author Image
Ruth Doyle