Where is the trailer plug on a 2012 Ford Expedition?

My 2012 Ford Expedition came with a factory hitch, and this 4-pin trailer connector to the left of it. The connector is in a rubber plug, and will slide down and out of the mount.

What is blue wire for trailer brake on Ford Expedition?

That’s actually the blue wire for the trailer brake. Even though this Expedition didn’t have the ‘towing package’, they still used the same harness for the RV / trailer connector. They simply capped off the brake wire since they only installed the 4-pin plug.

How do you install a new Ford Expedition connector?

The new bracket is held in place after drilling (2) holes and using the supplied self tapping bolts. The Hopkins connector snaps in to the bracket, and the Pollak harness plugs in to the back of it. The harness was covered in plastic wire loom, and then zip tied up and out of the way. The new connector is ready to use.

How long does it take to change spark plugs on Ford Expedition?

You should be able to apply the spark plug removal procedure shown in this video to the 2009-2014 Ford Expedition model years with the 5.4 Triton engine. This can be done with simple hand tools, and should only take about 2.5 hours to complete. It is a fairly easy process due to the newer Ford Motorcraft SP-509 spark plug design.

Is the positive battery cable on my Expedition Platinum corroded?

My 2017 Ford Expedition Platinum had the positive battery cable completely corroded. It was so extreme it actually ate the entire female connector around the terminal. I took it to the Ford dealer and they wanted $980 for the entire cable assembly and labor.

What kind of battery terminal does Ford Edge have?

2011-2014 Ford Edge MKX Positive Battery Terminal Cable Clamp OEM BT4Z14450AA 2011-2014 Ford Edge-Positive Battery Terminal2011-2014 Lincoln MKX-Positive Battery Terminal BT4Z-14450-AA. Stick with what you know and choose a Genuine OEM part These items are shipped from and sold by different sellers.

My 2012 Ford Expedition came with a factory hitch, and this 4-pin trailer connector to the left of it. The connector is in a rubber plug, and will slide down and out of the mount.

Do you need a trailer controller on a Ford Expedition?

When I purchased my 2012 Ford Expedition, it came with a hitch, and a 4-pin trailer connector. There wasn’t a brake controller installed, and I needed a 7-blade connector so I could pull my trailer.

Where is the 7 blade connector on a Ford Expedition?

As you can see, the Ford yellow went to the red on the new harness. Everything else was the same. The Hopkins 7-Blade RV Connector bracket will get located to the right side of the hitch. This way the door covering the connector doesn’t hit the trim on the bumper when you try to open it.

How to order Ford replacement OEM tow package wiring?

Call 800-298-8924 to order Tekonsha custom fit vehicle wiring part number 118242 or order online at etrailer.com. Free expert support on all Tekonsha products. Guaranteed Lowest Price and Fastest Shipping for Ford Replacement OEM Tow Package Wiring Harness, 7-Way.

What are the towing capacities of a Ford Expedition?

2015, 2016, 2017, 2018 & 2019 Models: Engine Gear ratio GCWR* (LBS.) Max. trailer Weight. 3.5L EcoBoost V6 3.15 12,300-14,900 6,600-9,200 lbs. 3.31 12,300-15,200 6,600-9,200 lbs. 3.73 12,300-15,300 6,600-9,200 lbs.

Where to find axle ratio on Ford Expedition?

2019 Ford Expedition Rear Axle Ratio Codes If you do not know the axle ratio of your vehicle, check its Truck Safety Compliance Certification Label (located on the left front door lock facing or the door latch post pillar). Below the bar code, you will see the word AXLE and a two-digit code.

What kind of interior does a Ford Expedition have?

Expedition featured an all-new front fascia, grille work, headlamps, body trim, rear fascia, tail lamps and liftgate. Interior fit and finish were improved with an all-new interior featuring new dash, door panels, genuine aluminium trim, and plush carpeting.

Where is the assembly plant for the Ford Expedition?

Prior to 2009, the Ford Expedition was assembled at the Michigan Assembly Plant in Wayne, Michigan (previously home to the Ford Bronco)., After 2009, the Ford Expedition was moved to the Kentucky Truck Plant in Louisville, Kentucky .

Are there Eddie Bauer versions of Ford Expedition?

Eddie Bauer versions could be optioned with the Eddie Bauer Premier package that included either monochromatic Arizona beige or solid black paintwork with painted alloy wheels and upgraded leather seating. A reverse sensing system was made optional. No major cosmetic or mechanical changes. Last year model for the UN93.

Is the Ford Expedition the replacement for the Ford Excursion?

Similar to the configuration of the Chevrolet Tahoe and Suburban, the Ford Expedition is sold in regular and extended lengths (the Ford Expedition EL/Max); sold since 2007, the latter functionally serves as the replacement for the Ford Excursion.

How do you install a brake harness on a Ford Expedition?

The 4-pin plug is cut from the factory harness, and the cap is cut off of the end of the factory blue trailer brake wire. The factory harness is then spliced in to the new Pollak harness, and sealed with electrical tape. Here is a chart with the wire colors and what circuit they go to.

Where is the trailer plug on a 2012 Ford Expedition?