Where is the ignition switch on a Chevy Silverado?

The Silverado’s ignition switch is not what your key goes into. That is called the lock cylinder. The ignition switch typically sits directly behind the lock cylinder. It has three main functions.

Can a bad ignition switch cause a Chevy Silverado to stall?

Your Silverado stalls because the faulty switch turns off the fuel pump or power to the ignition. When this happens, the engine will not be able to run until it gets that signal back. 2. Starts then Dies If your Chevy Silverado is starting right up, but then immediately dies, that is a very good indication that the ignition switch is bad.

How do you replace an ignition switch on a car?

Installing a Replacement Squeeze the release pin on the ignition switch so it’s flush with the side. The same release pin that stopped the switch from coming out now needs to be pressed in so you can slide the switch into place inside the ignition module. Slide the ignition switch into its hole.

What are the symptoms of a bad ignition switch?

These include stalling issues, not starting, and no power to the radio or accessories. The Silverado’s ignition switch is not what your key goes into. That is called the lock cylinder.

The Silverado’s ignition switch is not what your key goes into. That is called the lock cylinder. The ignition switch typically sits directly behind the lock cylinder. It has three main functions.

These include stalling issues, not starting, and no power to the radio or accessories. The Silverado’s ignition switch is not what your key goes into. That is called the lock cylinder.

The ignition switch is what feeds power to most of your truck systems including the transmission. There is a pink wire that goes down to the transmission Her. It should be hot. This wire feeds all the solenoids inside the trans. It also feeds the transmission range switch, known as the PRNDL. First check all of your fuses.

Can a bad ignition switch cause a bad transmission?

It’s possible you have a bad ignition switch. The ignition switch is what feeds power to most of your truck systems including the transmission. There is a pink wire that goes down to the transmission Her. It should be hot. This wire feeds all the solenoids inside the trans. It also feeds the transmission range switch, known as the PRNDL.

What do the codes mean on a Chevy Silverado?

Drove it 1 mile to service center. They put a scanner on it, it’s throwing following codes: Torque Converter PWM, PWM Solenoid. Clutch Solenoid. 1&2 shift Solenoid, 2-3 Solenoid. Dipstick for trans has bubbles, which could mean low fluid, but they say fluid level is fine.

Why is the shift indicator not working on my Chevy Silverado?

With the shift indicator light being off, tachometer not moving, speedometer not working and all the transmission codes you have, this sounds like electrical problem. It’s possible you have a bad ignition switch.

Where is the shift solenoid on an automatic transmission?

When it’s time to shift, the transmission control unit sends out power or ground to the required shift solenoid, and it causes the solenoid to open and let the transmission oil flow into the valve body, which then shifts to the next gear. The Transmission shift solenoids are located inside the valve body of your automatic transmission.

What does it mean when your transmission solenoid is broken?

This is a big sign that you have transmission shift solenoid problems because you have one or more shift solenoid for each gear, and if one is broken, it will not shift to that gear – instead, jump to the next gear directly. If the shift solenoid got damaged while the gear was engaged, it might cause the transmission to be stuck in that gear.

Why does my ignition key get stuck when I turn it on?

If the ignition key gets stuck when turning on the car or removing the key, it may be a sign of a worn out ignition switch. The key isn’t connecting inside the switch properly. Additionally, a switch going bad may cause the engine to continue running even after you’ve removed the key.

How to find a lost Chevy ignition key?

ALL KEYS LOST 1998-2001 CHEVY/GMC/CADILLAC IGNITION REMOVAL USING JIGGLER KEY & OBTAIN KEY CODE. – YouTube

How do you reset the PassLock on a 1998 Chevy truck?

Turn your key clockwise to crank the ignition. Wait for your truck to start, which confirms that you have successfully reset the passlock on your ’98 Chevy truck. Based in Chicago, Kenyonda Bradley has been writing for online publications since 2008.

What can cause a Chevy Silverado to misfire?

There is more to your Silverado’s ignition system than just the coil packs. There’s also spark plugs and plug wires. There are also non ignition related circumstances that can cause a misfire. That would include lack of fuel pressure, bad fuel injectors, or even a timing chain (or belt) that has jumped.

What is the ignition lock cylinder on a Chevy Silverado?

The ignition lock cylinder for Chevy Silverado 1500 is a component within your vehicle’s ignition switch. The part ensures that only a specific key starts your vehicle. It’s possible for the tumblers within the lock cylinder to get worn out, so the part won’t be able to work even with your key.

Why is my Chevy Silverado not turning on?

If your key doesn’t fit or turn in the ignition lock cylinder, your engine won’t turn on, so shop for durable replacement parts from AutoZone. The ignition lock cylinder for Chevy Silverado 1500 is a component within your vehicle’s ignition switch. The part ensures that only a specific key starts your vehicle.

What’s the name of the ignition lock cylinder?

The ignition lock cylinder is the cylindrical tumbler and key that is used to power on and start the vehicle. While many newer vehicles are now being manufactured with push button and keyless power and starting systems, traditional ignition lock cylinders are still commonly found on many road…

What are the symptoms of a bad ignition lock cylinder?

If the ignition lock cylinder wear out or breaks, it may prevent the vehicle from starting when the key is inserted and turned. 3. Issues inserting and removing the key. Issues with inserting and removing the key are another symptom of a potential problem with the ignition lock cylinder.

What should I do if I need to replace my ignition switch?

Reconnect the cable to the negative (-) terminal on the battery, then insert the key into the ignition and turn it to start the vehicle. The vehicle should start without any issue. If it doesn’t, remove the ignition switch and reinstall it. Shut the engine off (if it starts) and disconnect the battery again.

How can I Fix my Chevy Silverado ignition?

Wedge a shim in the connection and secure the new connection with hot glue, silicon or any other glue that can be fairly easy to scrap off and remove if further maintenance is required. Replace the steering column cover and that’s how you fix the ignition in your GMC Sierra or Chevy Silverado 1500, 2500 and 3500. Loading…

Is there an easy fix for a GMC ignition switch?

This is one way to fix a very complicated electrical system in the Chevrolet and GMC cars and trucks. Some are easy fixes with loose or bad electrical connections. Others involve the ignition switch itself, and others involve one of the computers that the system communicates with when starting the vehicle.

What’s the best way to replace an ignition switch?

The easiest way to re-install the switch is to rotate the key in the ignition to the “accessory” position (fully counter-clockwise). Then, rotate the gear on the top of the new ignition switch fully COUNTER-CLOCKWISE (as you are looking at it like it goes in the slot). This way, you will not be off one or two teeth when you put it back in. 13.

Why does my Chevy Silverado not start up?

Others involve the ignition switch itself, and others involve one of the computers that the system communicates with when starting the vehicle. The security system may have a number of issues, including the installation of a remote starter, causing the car or truck not to start. Most complaints involve a blinking security light.

How do you remove ignition switch from car?

Insert a straightened out paperclip into the slot just to the left of the key cylinder. This will lock the cylinder from starting. Inserting your screwdriver into the cylinder and turn it as far as you can to the right. Pull on both the paperclip and the screwdriver to gently slide the switch out of its current position.

How can I Turn Off the ignition without a key?

Be sure to make the hole large enough for you to insert your screwdriver, and drill to the back of the key slot. Insert a straightened out paperclip into the slot just to the left of the key cylinder. This will lock the cylinder from starting. Inserting your screwdriver into the cylinder and turn it as far as you can to the right.

What is the ignition switch on a Chevy Silverado?

An ignition switch for Chevy Silverado 1500 is the part that sends the key signal to your vehicle’s starter relay. Dirty or failed contacts in this component mean your truck won’t be going far, so make moves when your truck’s on the ropes.

How to remove the ignition switch without a key?

How to Remove the Ignition Switch Without a Key. 1 Step 1. Turn on your power drill and use your drill bit to make a hold in the key slot of the ignition cylinder. Be sure to make the hole large enough 2 Step 2. 3 Step 3.

When to replace ignition switch in Chevy Tahoe?

1995-1998 GMC/Chevy pickup, tahoe, blazer, suburban, etc. ignition switch replacement. If you’re truck won’t start, the gauges aren’t working, or you have random transmission problems, the ignition switch could be at fault. This is a step by step tutorial on how to fix a broken ignition switch. Loading…

How to fix ignition problems by replacing the ignition switch?

How to fix ignition problems by replacing the ignition switch. Ignition switch location, inspection, removal and repair. DIY car repair with Scotty Kilmer, an auto mechanic for the last 43 years. 1. Screwdriver set: http://amzn.to/2j92UCG 2. Disposable Gloves: http://amzn.to/2zSRuxO 3. Common Sense 4. Full HD Camera: http://amzn.to/2AvoEk7 5.

Why is my ignition not working on my Chevy Silverado?

The contact owns a 2002 Chevrolet Silverado 1500. The contact stated that while operating the vehicle, the driver side seat belt would suddenly retract and prevent the contact from moving. Also, the contact indicated that the ignition key became lodged in the ignition switch and could not be removed.

Are there any problems with my Chevy Silverado?

Other Common Electrical System related problems of Chevrolet Silverado 1500 Problem Category Number of Problems Dash Wiring problems 16 Ignition Switch problems 14 Battery problems 14 Software problems 14

Is there a problem with the ignition switch on a 2014 Chevy Silverado?

Tl-the contact owns a 2014 Chevrolet Silverado 1500. The contact received NHTSA campaign number 19v64500 service brakes,hydraulic. The contact stated that upon starting the vehicle the ignition switch locked and failed to release the key while the brake pedal was depressed.

What happens when you turn the ignition key in a Chevy Silverado?

Power the Accessories- This should be what you get when you turn the key to the first position. This allows you to use the power windows, radio, and any other accessory that is equipped in your Chevy Silverado.

Why does my Chevy Silverado 1500 not start?

Ignition switch intermittently stops working. It will cut off while driving city streets and at high speeds and the lock buttons will lock and unlock repeatedly while showing the truck in park, all while going down the expressway. It’s terrifying. Sometimes it won’t start or do anything. But if I jiggle it then it will start.

How to replace an ignition switch in a 1983 Chevy?

Both are operated remotely by long rods that run the length of the column, and both are removed to replace the ignition switch. Raise the hood and disconnect the negative battery cable.