What to do if your suburban fuel pump goes out?
What to do if your suburban fuel pump goes out?
There are physical signs that you can feel when your Suburban’s fuel pump is going out. Before taking anything apart, check to see if your engine’s computer has any trouble codes saved in it. The engine may throw a P0087 trouble code.
When was the last time my Chevy fuel pump failed?
The technical service bulletin that explains the cause of the repeat failure of the Chevy fuel pump replacement unit covers all years from 1996 to 2003 and includes all of the pickup trucks. Also included is the Tahoe and suburban and their GMC counterparts such as the Sierra and Envoy. Oh and don’t forget the Cadillac Escalade is also included.
When do you replace the fuel pump harness?
If you have a fuel pump harness connector that looks like the flat one on the right or the square one at the bottom, then consider replacing it when replacing the pump. More details about this are below, but you might want to download your Chevy manual to help.
Where is the fuel pump sensor on a GMC Truck?
Its located on the drivers side of the throttle body. Its the top sensor. Try turning your key to the run position a few times (with out starting). Then try to start it. If it starts, sounds like what mine did. I replaced the fuel pump assembly and that fixed the problems.
There are physical signs that you can feel when your Suburban’s fuel pump is going out. Before taking anything apart, check to see if your engine’s computer has any trouble codes saved in it. The engine may throw a P0087 trouble code.
How long does it take to replace fuel pump?
Spin the locking ring to unlock the pump, lift it out, spill gas on yourself, and clean the surface that the o-ring sits in so that you are ready for installation of the new pump. The entire process of removal and reinstallation of the pump itself is a 5 minute job, and I love them for that.
How to remove fuel pump from Hot Rod?
Removing the pumps from the tanks is just like any other fuel tank on your hot rod. Spin the locking ring to unlock the pump, lift it out, spill gas on yourself, and clean the surface that the o-ring sits in so that you are ready for installation of the new pump.
Can a bad fuel pump cause an engine to turn over?
If any of these things aren’t present, the engine won’t turn over at all. If there’s been zero warning that the fuel pump could be going bad (hesitation, difficulty starting, etc) then it should not be automatically assumed that the fuel pump is at fault.
If any of these things aren’t present, the engine won’t turn over at all. If there’s been zero warning that the fuel pump could be going bad (hesitation, difficulty starting, etc) then it should not be automatically assumed that the fuel pump is at fault.
How can I tell if my fuel pump is working?
The only way to truly tell is to place a fuel pressure gauge on both sides of the line and get a reading from both. If your car isn’t starting at all, and you hear the fuel pump prime that is usually a good indication that the pump is working to some capacity.
What happens if you replace the fuel pump?
– Bed has no affect on pump circuit. Also if you had to replace the connector for the new PUMP MODULE, (i hope) make sure color code is correct, some dont match up. Read instructions again! Be sure the four wire connectors are making good contact.
Where does the fuel pump go in a truck?
Searched forever for an answer. It turns out that in order to remove the bed of the truck, you must disconnect the ground for the fuel pump, which attaches in the rear on the drivers side. IIRC it ran either in or alongside the harness for the tail light wiring. Once I hooked that back up, my truck started right up.
What are the symptoms of a bad fuel pump?
A clogged fuel filter will have high pressure on its input side and low pressure on its output side. A bad fuel pump will have low pressure on both sides. They are both going to cause the same hesitation at high speed and difficulty starting.
The only way to truly tell is to place a fuel pressure gauge on both sides of the line and get a reading from both. If your car isn’t starting at all, and you hear the fuel pump prime that is usually a good indication that the pump is working to some capacity.
What happens if my Chevy Suburban fuel pump goes bad?
If your Chevy Suburban’s fuel pump goes bad, no fuel (or not enough fuel depending on whether or not it’s out all the way) can enter the engine. Without gas your Suburban will not run at all. With that in mind, most of the symptoms of a bad fuel pump revolve around the vehicle stalling out or not running at all.
What causes a Chevy Suburban to not start?
The most common causes that hinders normal starting operation of your Suburban are dead key fob battery, dead 12v battery, corrosion on battery terminals, bad alternator, clogged fuel filter, broken starter, blown fuse, empty gas tank, immobilizer error or any fault in the electrical system. 1. Weak Battery
What to do if your fuel pump wont start?
For future reference, I had this same problem when replacing the fuel pump on my 2002 s10 4.3L. Searched forever for an answer. It turns out that in order to remove the bed of the truck, you must disconnect the ground for the fuel pump, which attaches in the rear on the drivers side.
Why does my son’s GMC Sonoma not start?
I have a huge favor and I’m stuck my son has a 2003 gmc Sonoma pulled into our driveway went to start it back up it would not start checked everything and it seem to be the fuel pump so we purchased a new fuel pump and we still can’t get it to start we have replaced the control module and it still won’t start any buddy have any ideas
Where is the connector on a Chevy fuel pump?
When you get the Delco replacement parts it comes with a new connector on the fuel pump side. The problem is the connector on the vehicle side of the harness. In the online Chevrolet repair manual I use, a Tech Tip states, the connector should be replaced with the fuel pump assembly.
Why does my Chevy fuel pump keep failing?
The Chevrolet service bulletin states that the cause of the repeat failures is due to worn or damaged electrical connectors at the fuel pump assembly. When you get the Delco replacement parts it comes with a new connector on the fuel pump side.
What do I need to replace my fuel pump?
This factory replacement unit also includes the fuel level gauge sender, hanger assembly and tank filter sometimes called the sock. Some aftermarket replacement pumps just include the motor. This means you replace the motor and transfer the used fuel pump sock, fuel sending unit, and hanger assembly.
When you get the Delco replacement parts it comes with a new connector on the fuel pump side. The problem is the connector on the vehicle side of the harness. In the online Chevrolet repair manual I use, a Tech Tip states, the connector should be replaced with the fuel pump assembly.
This factory replacement unit also includes the fuel level gauge sender, hanger assembly and tank filter sometimes called the sock. Some aftermarket replacement pumps just include the motor. This means you replace the motor and transfer the used fuel pump sock, fuel sending unit, and hanger assembly.
Where can I get a fuel pump harness replaced?
Replacement of the harness connector is a fairly simple operation and the parts are readily available from your GM dealer parts department. With the cost and difficulty of the repair it’s wise to follow the technical service bulletin. Take a few extra minutes and replace the connector.
What are the fuses on a Chevy Suburban?
Ignition Switch, EGR, Canister Purge, EVRV Idle Coast Solenoid, Heated O2, Fuel Heater (Diesel Engine), Water Sensor (Diesel Engine) WARNING: Terminal and harness assignments for individual connectors will vary depending on vehicle equipment level, model, and market.
How to test a GM 4.3L fuel pump?
More GM 4.3L, 5.0L, and 5.7L Tutorials. It’s very important that you start off your fuel pump relay diagnostic by first testing the fuel pump pressure with a fuel pressure test gauge. If the fuel pump relay IS NOT activating the fuel pump, the fuel pressure test gauge will register 0 PSI when cranking the engine.
How to test a GMC fuel pump relay?
TEST 1: Swapping Out The Fuel Pump Relay. TEST 2: Making Sure The Fuel Pump Relay Has Power. TEST 3: Bypassing The Fuel Pump Relay. TEST 4: Bench Testing The Fuel Pump Relay. Fuel Pump Circuit Diagram. Where To Buy The Fuel Pump Relay. More GM 4.3L, 5.0L, and 5.7L Tutorials.
Where do you find the fuel pump relay?
When you shut off the ignition, it powers down the fuel pump. In most vehicles, the fuel pump relay can often be found in the fuse box in the engine bay, which is usually a long black box which contains fuel pump relay along with various other fuses and relays.
More GM 4.3L, 5.0L, and 5.7L Tutorials. It’s very important that you start off your fuel pump relay diagnostic by first testing the fuel pump pressure with a fuel pressure test gauge. If the fuel pump relay IS NOT activating the fuel pump, the fuel pressure test gauge will register 0 PSI when cranking the engine.
What kind of fuel pump does a Chevy Tahoe have?
This tutorial will show you how to test the fuel pump relay on your 1997, 1998, 1999 Chevrolet/GMC full-size Pick Up, Suburban, Tahoe, or Yukon. It’ll also show you how to bench test the fuel pump relay in a step-by-step way to find out if it’s defective or not.
How to change a broken fuel pump without dropping the gas tank?
TheCousinDan shows you how to change a broken fuel pump without dropping the gas tank. This time it’s done by actually cutting a hole in your car (don’t worry, it’s not as bad as it sounds). Music: NCS Def Kev
What kind of fuel pump does a Chevy Tahoe have?
This tutorial will show you how to test the fuel pump relay on your 1997, 1998, 1999 Chevrolet/GMC full-size Pick Up, Suburban, Tahoe, or Yukon. It’ll also show you how to bench test the fuel pump relay in a step-by-step way to find out if it’s defective or not.
When to know if your fuel pump is bad?
This trouble code detects that the fuel rail/system pressure is too low. Any trouble codes that exist could be a clue. Sometimes when there is low fuel pressure, you may also get an oxygen sensor related trouble code as well. The real issue with diagnosing a bad fuel pump is that it resembles many other vehicular issues in terms of symptoms.
What causes the fuel pump to not start?
The fuel pump is running and delivering normal pressure to the engine But, with all that working your engine still will not start. So, the most likely cause, is that the fuel injectors are probably not opening. The (PCM) uses the trigger signal from the crankshaft position sensor; and/or camshaft position sensor to pulse the injectors.
I have a huge favor and I’m stuck my son has a 2003 gmc Sonoma pulled into our driveway went to start it back up it would not start checked everything and it seem to be the fuel pump so we purchased a new fuel pump and we still can’t get it to start we have replaced the control module and it still won’t start any buddy have any ideas
What happens when the fuel pump relay goes bad?
If the fuel pump relay suddenly fails, it will light up the check engine light and store a trouble code on the fuel pressure. The fuel pump relay going bad can affect the fuel pump’s power and affect fuel delivery to the engine.
The fuel pump is running and delivering normal pressure to the engine But, with all that working your engine still will not start. So, the most likely cause, is that the fuel injectors are probably not opening. The (PCM) uses the trigger signal from the crankshaft position sensor; and/or camshaft position sensor to pulse the injectors.
What happens when you replace the fuel filter?
Fuel filter; this should always be replaced with the pump because even a partially clogged filter is a pump killer. Stuck fuel pressure regulator. Restriction in the return line to the fuel tank. (Disconnect and try blowing through it)
How to remove a fuel pump from a truck?
Basic instructions on how to tip your bed and remove your fuel pump and sender assembly, replacement of the fuel pump from the sender unit and putting it back into the tank with gasket o-ring and lock ring. I also show video of the bolt hole locations on my short bed frame. Loading…
Where to mount an electric fuel pump in a Chevy?
Cover the hole with a block-off plate gasket and sealer. Mount the electric fuel pump near the gas tank and connect it to the fuel line. Install a filter next to the electric fuel pump. Wire the electric fuel pump to the ignition switch.
Basic instructions on how to tip your bed and remove your fuel pump and sender assembly, replacement of the fuel pump from the sender unit and putting it back into the tank with gasket o-ring and lock ring. I also show video of the bolt hole locations on my short bed frame. Loading…
What do you need for electric fuel pump?
Parts You’ll Need 1 An electric fuel pump that will fit your year, make, and model 2 All the wires to hook it up to your car (or a universal wiring kit if you want to re-wire the entire car while you’re at it) 3 A block-off plate gasket and sealer 4 A mount for the electric fuel pump
Can a mechanical fuel pump be replaced with an electric fuel pump?
Leave the mechanical pump in place and put an electric one by the tank: You can do this if you want to keep your mechanical fuel pump as a backup in case your electric fuel pump gives out. This is arguably unnecessary because electric fuel pumps are designed to last a long time. 2.
Why does my fuel pump only run for a few seconds?
This sound is the electric fuel pump trying to prime the fuel system. It will only run for a few seconds and then shut off. If you are not sure you could hear it or if there is noise outside; you may have to try it several times. Turn the key on and wait then turn it off.
A clogged fuel filter will have high pressure on its input side and low pressure on its output side. A bad fuel pump will have low pressure on both sides. They are both going to cause the same hesitation at high speed and difficulty starting.
Where to check for no start fuel pump?
The first thing you want to do is check the fuse panel to see if the fuse is blown. If your car has two fuse panels than the one in the engine compartment; should be the correct one to check. The fuse panel or circuit box is usually located near the battery; and is a small black box with a removable lid.
Why does my fuel pump not prime when I turn it on?
Pulled fuel pump relay and put in a jumper wire to run the fuel pump and it started. Put the fuel pump relay back in and it starts and drives, but the fuel pump still doesn’t prime when turning the key on. I’m afraid that after sitting overnight, it will once again refuse to start.
The engine may still crank when the key is turned, however it will not be able to start due to lack of fuel. This symptom can also be caused by a wide variety of other issues, so having the vehicle properly diagnosed is highly recommended. 3. No noise from the fuel pump
How can you tell if your suburban fuel filter is bad?
There are physical signs that you can feel when your Suburban’s fuel filter is clogging. Before taking anything apart, check to see if your engines computer has any trouble codes saved in it. The engine may throw a P0087 trouble code.
Where is the fuel filter on a Chevy Sonic?
Things began to change in the 80’s. Fuel injection requires higher fuel pressure. Higher fuel pressure meant that a more robust fuel filter would be required. This meant the fuel filter was no longer left under the hood. It was put in the steel fuel line, between the gas tank and engine bay.
This trouble code detects that the fuel rail/system pressure is too low. Any trouble codes that exist could be a clue. Sometimes when there is low fuel pressure, you may also get an oxygen sensor related trouble code as well. The real issue with diagnosing a bad fuel pump is that it resembles many other vehicular issues in terms of symptoms.
Where is the fuel filter on a Chevy Suburban?
This meant the fuel filter was no longer left under the hood. It was put in the steel fuel line, between the gas tank and engine bay. These fuel filters were more reliable, but they also were tougher to change.
What are the symptoms of a bad fuel filter?
Here are the most common symptoms of a bad fuel filter in your Chevy Suburban: Sputtering Under Load The only way that you are going to know that your Suburban’s fuel filter may be going out is that it is no longer letting enough fuel through to keep the engine running under a heavy load, or at high-speed.
Things began to change in the 80’s. Fuel injection requires higher fuel pressure. Higher fuel pressure meant that a more robust fuel filter would be required. This meant the fuel filter was no longer left under the hood. It was put in the steel fuel line, between the gas tank and engine bay.
How to check no fuel condition on GM 4.3L?
I’ve also included how to check a no fuel condition with starting fluid (although this is not the most effective way to test the fuel pump). It’s been my experience that misdiagnosing a bad fuel pump is a common occurrence on the 4.3L, 5.0L, 5.7L GM vehicles with the ‘Spider’ fuel injector assembly.
Where is the fuel pump in an engine?
Fuel pumps are a simple and rugged part of the fuel system. They are usually found inside of the fuel tank and are responsible for sending fuel from the tank to the engine.