What should I do if my EGR light is not working?

The repair of this condition is removal of the EGR valve and inspection of the passageway to check for a blockage. Each model vehicle has different procedures for clearing the passageway due to many different configurations of the system. Some Fords have a removable tube.

Why is the EGR valve on my Chevy truck not working?

The most common EGR system failure on our trucks is the valve itself; the diaphragm fails so the EGR valve will not open. You can eliminate this possibility right off the bat by testing the valve with a vacuum tester (Mityvac.) Shut the engine off and connect the tester directly to the EGR valve.

How can I check the voltage of my EGR solenoid?

With the meter set on DC voltage, or using a test light, check the EGR solenoid harness terminal A (pink/black) to ground. Key on, meter should read 12V or the test light should light up. Do not pierce the wire to test, simply unplug it and touch the test lead to the connector pin.

Why is there an EGR code on my Ford?

However, we often find EGR codes on Ford products caused by inexpensive plastic parts that falsely report position to the control module. Several technical service bulletins for a wide variety of different makes and models have documented different problems associated with the EGR valve system.

What should the meter read for EGR recirculation?

With the meter set on ohms, you can test the EGR solenoid coil across the two pins in the socket; any reading less than 20 ohms indicates a bad solenoid winding. With the meter set on DC voltage, or using a test light, check the EGR solenoid harness terminal A (pink/black) to ground. Key on, meter should read 12V or the test light should light up.

Why is EGR not needed at engine idle?

This feature reduces or eliminate engine ping caused by early detonation. This function is not needed at engine idle or when the vehicle is cold. This is why the EGR system is quite complicated and receives many inputs from other sensors that facilitate its operation.

What’s the diagnostic code for the EGR valve?

Several technical service bulletins for a wide variety of different makes and models have documented different problems associated with the EGR valve system. With some exhaust gas issues you might set a diagnostic trouble code of PO401 or P0402.

Why does my check engine light not come on?

You may also set trouble codes for an engine misfire, which would be in the PO300 range. It’s also possible your check engine light will not come on and you’ll just experience a noticeable problem such as rough engine idle or even engine stalling.

How to reset exhaust gas recirculation ( EGR ) value with?

5)Using a soft bristled tooth brush, scrub the EGR Valve, spray further cleaner into valve if needed. Once all traces of carbon are removed, using a lint free cloth dry the EGR Valve. 6)Disconnect vacuum pump or OBDⅡ diagnostic tools.

Why do I have an EGR code on my car?

This is often due to carbon clogging passageways or improper operation of the egr-valve. However, we often find EGR codes on Ford products caused by inexpensive plastic parts that falsely report position to the control module.

Can a faulty EGR valve cause a check engine light?

As with most engine component issues, a faulty EGR valve will also likely trigger the vehicle’s check-engine light. Obviously, the check-engine light illuminates for a long list of issues, so the next step in diagnosing the issue is to have your vehicle’s computer scanned for trouble codes.

What does EGR stand for in a car?

EGR stands for exhaust gas recirculation, a vehicle emissions control concept used in both gasoline and diesel engines. The EGR valve — which works differently depending on how old the car is and whether it uses gasoline or diesel fuel — is a key component to a car’s exhaust system and engine health. Related: What Is a Boxer Engine?

What causes a failure code on an EGR system?

Another common problem causing failure codes in this system is that the tip of the valve will become irregular shaped from carbon deposits. When this happens it no longer creates a perfect seal. This can allow exhaust gas to continue to flow when not called for by the computer. An example would be at engine idle or when the vehicle is cold.

How does an exhaust gas recirculation ( EGR ) valve work?

The EGR (Exhaust Gas Recirculation) valve helps lower the car’s exhaust emissions (gases from the tailpipe). It recirculates the portion of the gasses coming out of the engine by putting in back into the intake manifold, where the engine can burn it again, thereby reducing the emissions. The EGR

When does the engine check light turn on?

The engine check light will illuminate when there is a faulty in the EGR valve. This light will not turn on until your vehicle’s computer picks up a negative signal from your EGR valve or any other engine component. Anytime you see your engine check light on, carry out a thorough examination of your vehicle’s engine as soon as possible.

What’s the best way to test an EGR valve?

The best way to test this valve is to purchase a vacuum tester. Not only that it is used for testing the valve, but you can also use it to bleed your brakes plus perform a lot of automotive maintenance.

When does the Check Engine light come on on an EGR cooler?

Check Engine Light comes on. Another symptom of a bad or failing EGR cooler is a Check Engine Light. If the computer detects a problem with the EGR system, such as insufficient flow or exhaust, it will set off the Check Engine Light to alert the driver of the issue.

How can you tell if your EGR valve is faulty?

If your valve is working properly, you will observe a component inside the valve moving up and down. You can rev your engine a couple of times to be sure you are getting the movement. If you do not observe this movement, then it is a sign that your EGR valve is faulty.

What do you need to know about EGR codes?

A basic explanation of the valve works would probably help with the understanding of the diagnosis and repair of EGR codes. Exhaust gas recirculation is necessary for emissions purposes. Unfortunately, when it malfunctions it can actually push emission levels off the chart.

What’s the best way to reset a check engine light?

In such a case, it is highly recommended to check the codes with a scanner instead. Switching the ignition on and off is also one method of hard reset without disconnecting batteries. Put the keys in your ignition and turn your ignition on and off consecutively after a second in each step.

What to do if your EGR monitor is not running?

Start with making sure your vehicle has no known EGR monitor setting issues identified by the BAR and CARB, and next get in to hands-on diagnosis of what is causing the monitor to either not run or not complete. Since the check engine light is not on, we can be confident the ECU has not found any specific emission component failure.

What to do if you have a bad EGR valve?

The first thing you do is to locate your EGR valve. You can take a look at the manufacturer’s guide of your vehicle to help you with this. Then put on your vehicle’s engine and rev your engine to about 2000 rpm. Gently create access to your valve and place your hand on it.

How to get rid of check engine light error?

Then put your key into the ignition and turn it three times to the “ON” position. This will clear the emissions data from the vehicle memory as well as the readiness flag data. Reconnect the positive battery cable and turn the key in the vehicle ignition. Wait one minute and the check engine light error should be gone. 4. Use an OBD Code Reader

Why does my check engine light come on when my EGR valve is stuck?

Whether the EGR valve is clogged, stuck open, or stuck closed, you’re going to get a check engine light. While the check engine light will usually point you straight to the EGR valve, it is possible that it might come on due to a symptom instead of a cause.

What’s the code for an EGR valve throw?

What code will an EGR valve throw have? The P0401 trouble code is related to your car’s exhaust gas recirculation (EGR) system, which controls an engine and reduces emissions. Suppose a computer-controlled valve gives a certain amount of gases back into your engine to be burnt with the air-fuel mixture.

What does an illuminated check engine light mean?

An illuminated Check Engine Light is another symptom of bad or failing EGR valve. If the computer detects an issue with the vehicle’s EGR valve circuit or position, it will set off the Check Engine Light in order to notify the driver of the issue.

What are the symptoms of a leaking EGR valve?

A faulty EGR valve or related component may leave the valve in either the stuck open or stuck closed position. The symptoms of a stuck open EGR valve are a rough idle with a lean air fuel mixture. The engine has a major vacuum leak. The symptoms of a stuck closed EGR valve are pre-ignition, ping, and knock.

What is EGR problem?

The EGR system works by recirculating a portion of the exhaust gas off the engine back to the engines cylinders. Modern engines require an EGR system to reduce the amount of emission and meet government standards. Problems with the EGR valve often include a leaking or clogged valve.

What is EGR valve failure?

An EGR valve. Failure to repair or replace the ERG valve could increase emissions from the car. A faulty EGR valve may result in a stalled car. An issue with an EGR valve is often diagnosed through reading the car’s diagnostic trouble codes. A trusted mechanic may be able to repair the EGR valve instead of replacing it.

What does EGR do?

EGR stands for Exhaust Gas Recirculation . It is part of the vehicle emmissions system, and is used to reduce combustion temperature and pressure to control Oxides of Nitrogen. There are generally three parts to the EGR system: the EGR valve, an actuator solenoid, and a differential pressure sensor EGR…

Why is EGR important to the p0401 code?

Usually on an OBD2 system that sets the P0401, the ECM/PCM must see the failure on two consecutive trips before it will permanently set the code and trigger the Check Engine Light. The EGR system is important because it reduces emissions by allowing burnt exhaust gas to flow back into the engine.

What is the code for insufficient flow on a check engine light?

Someone gets a check engine light. To save money they take the car to aurozone or read the codes with a code reader. The code description is for a flow problem with the EGR.

How can I check if my EGR valve is OK?

A quick way to check for this is to apply vacuum to the EGR valve and monitor engine operation. Assuming the EGR valve is ok the engine should begin to stumble and possibly even stall as vacuum is applied to the valve and the pintle opens. Your DPFE voltage should also approach 4.5 volts.

Why does my dpfe have a leaking EGR valve?

You now know the DPFE, EGR valve and tube and hoses are okay and we can move on to test the EVR (EGR Vacuum Regulator), part of the system. If the reading did not change, then you could suspect a leaking EGR valve, allowing uncommanded flow of exhaust gases.

Someone gets a check engine light. To save money they take the car to aurozone or read the codes with a code reader. The code description is for a flow problem with the EGR.

What happens when you replace the EGR tube?

In order to fix this issue, you’ll have to replace the EGR tube and reset the error codes with a diagnostic scanner before testing the repair. There are rattling sounds coming from the engine. When the EGR tube is loose, it will often rattle and cause a loud vibration to occur under the hood of the vehicle.

How can I Reset my Check Engine light?

You should always have the codes generated by your car’s computer scanned and read so you can determine the cause. You can reset the light once you have fixed the problem. When the check engine light goes on, an error code is saved in the car’s computer.

How do you remove an EGR valve from a car?

Use a boxed end wrench to loosen the nuts connected to the EGR valve and then remove the old EGR tube from the vehicle. Step 8: Clean the EGR valve. Using carburetor cleaner, soak a shop rag and clean the port on the EGR valve that connects to the EGR tube.

Which is the diagnostic code for a GMC check engine light?

1 Refer to our Generic OBD II code list for definitions on all other GMC diagnostic trouble codes. 2 Manufacturer Specific Codes 3 P1031 4 P1032 5 P1105 6 P1106 7 P1107 8 P1108 9 P1109 10 P1111

Can a check engine light get clogged up?

The EGR valve can get clogged up or fail entirely. If you’re even slightly mechanically inclined, you can remove the valve, clean it up, and reinstall it in a relatively short amount of time. If the valve needs to be replaced, expect to pay at least $125 for a brand-new, OEM-quality unit.

When to replace the EGR valve on a diesel engine?

The EGR valve on a diesel engine usually gets a lot more dirt in it, and it has to be replaced and cleaned more often. The carbon build up can also destroy the EGR valve and you have to replace it more often. A lot of people, reprogram the EGR valve to not function to reduce the amount of carbon build up in the engine.

What should I do if my EGR light is not working?