Most popular

What should I do if my dash gauges are all out?

What should I do if my dash gauges are all out?

Dash gauges are all out and no power windows and no blower for air and heater and its as something shot or blew but the two places that I checked the fuses are not blown. What else might I do to see if the problem can be fixed without going into the shop? have the same problem? Will the vehicle start and run?

Why are all of the gauges in my car not working?

There are a lot of different types of instrument cluster designs and configurations, but when all of the gauges in a car stop working at once, the problem is usually either a fuse or wiring problem. The first step in diagnosing this type of issue is to identify the fuse associated with the instrument cluster or gauges.

What does it mean when your speedometer is not working?

If the oil pressure, coolant, charge, or gas gauge doesn’t work or works erratically, the problem is in the gauge, wiring, or sender. Speedometers are unique in that some of them use physical cables instead of sensors, so a speedometer not working can also indicate a broken cable or stripped gear.

What to do if your coolant gauge is not working?

Using your coolant temperature gauge as an example, the diagnostic procedure involves locating and disconnecting the sending unit. With the ignition on, the gauge should register cold. If you connect the sending unit wire to ground, the gauge should switch to read hot.

What causes your gauges not to work on dash board?

The most common causes of the gauges in a car not working can be broken down into three scenarios: None of the gauges work. If none of the gauges work at all, the problem may be a blown fuse or a defective instrument cluster. An individual gauge doesn’t work. If the oil pressure, coolant, charge, or gas gauge doesn’t work or works erratically, the problem is in the gauge, wiring, or sender. One or more dashboard warning lights don’t work.

Why do the dash lights and gauges do not work?

When an instrument cluster isn’t properly grounded , you’ll typically find that the gauges and dash lights fail to work or only work intermittently. You may be able to check the ground by looking up under the dash with a flashlight, but you will have to actually remove the instrument cluster in many cases.

What causes dashboard gauges to stop working?

But when the gauges in your car stop working, it’s not a situation you can safely ignore. When one gauge stops working, the problem may be in the gauge itself or a bad sensor, while all the gauges cutting out at the same time often indicates a blown fuse or a defective instrument cluster.

Why do my dash lights not work?

The most common causes for this dashboard light problem is the lights not receiving power, or the lights themselves being blown out. With the fuses being checked and shown to be okay the lights themselves may be the issue.

Why are the dash gauges on my Chevy Silverado not working?

There are known issues with the gauges on the 03 silverado. Even though the cages appear analog, they are stepper motor controlled by the computer. This is a fancy way of saying digital. Check with the dealer about a recall! Since all gauges appear to have quit at one time I would agree with a previous post that the computer program is flawed.

What does it mean when gauges in your car stop working?

But when the gauges in your car stop working, it’s not a situation you can safely ignore. When one gauge stops working, the problem may be in the gauge itself or a bad sensor, while all the gauges cutting out at the same time often indicates a blown fuse or a defective instrument cluster.

Why is my Chevy 2500HD oil gauge not working?

04 2500 HD DURAMAX DASH PROBLEMS. Tach works for awhile then stops altogether, will work when I drive the next time. Know my oil gauge is acting up. Checked with GM dealer, they informed me that the warranty on the dash ran out at 70,000mi. (85000) when my problems started. Whole panel has to be replaced. 04 2500 HD DURAMAX DASH PROBLEMS.

Dash gauges are all out and no power windows and no blower for air and heater and its as something shot or blew but the two places that I checked the fuses are not blown. What else might I do to see if the problem can be fixed without going into the shop? have the same problem? Will the vehicle start and run?

What kind of problem is a lost gauge?

First instinct would be a ground problem but from your description it sounds like a Class2 data line problem and not an easy fix without some advanced knowledge and a scantool.

How long does it take for no bus gauges to work?

After 15 minutes and all the dash panels have been removed for the second time (why didn’t I off load this the first time) it starts working again. But, What did I do??

After 15 minutes and all the dash panels have been removed for the second time (why didn’t I off load this the first time) it starts working again. But, What did I do??

Why are my dashboard gauges not working on my car?

Q: Could the reason for my dashboard gauges not working be a fuses and or fuses needing to be replaced? I was just wondering if the reason for my gauges on my car not working (gas, speedometer, temperature, RPM) would be because there may be a fuse that needs to be replaced

What should I do if my gauges are not working?

The first step in diagnosing this type of issue is to identify the fuse associated with the instrument cluster or gauges. The fuse should have power on both sides when the ignition key is turned to the on position.

Is there no bus, no gauges possible solution?

I’d like to offer my solution to the frustrating “no bus and no gauges” problem that I see is pretty common. I have a 2000 ram 1500 2X with the 5.9 automatic, however I believe that this is applies to all gen2 trucks regardless of drivetrain or engine type.

What kind of truck has no bus gauges?

I have a 2000 ram 1500 2X with the 5.9 automatic, however I believe that this is applies to all gen2 trucks regardless of drivetrain or engine type. My Story… See the end to get straight to my find. I’ve had my gauges go out with the “no bus’ message in the odometer window three times now!

Why does my car gauge read cold when I Turn on the ignition?

With the ignition on, the gauge should register cold. If you connect the sending unit wire to ground, the gauge should switch to read hot. If the gauge moves as expected, then you can suspect a bad sending unit. If the gauge doesn’t move when you ground out the sensor wire, then you can suspect a bad gauge.

Where are the fuses for the dashboard lights?

Check under the hood, under the dashboard, or near or in the glove compartment. Once you find the fuse box or boxes, remove the lid and check the diagram on the underside of the lid for a fuse labeled “dash lights” or just “lights.” Refer to your owner’s manual if you have trouble locating the fuse boxes or the dashboard light fuse.

There are a lot of different types of instrument cluster designs and configurations, but when all of the gauges in a car stop working at once, the problem is usually either a fuse or wiring problem. The first step in diagnosing this type of issue is to identify the fuse associated with the instrument cluster or gauges.

What to do if your car dashboard lights are not working?

Removing the old fuse and replacing it should get the lights working again. While the new fuse may do the trick, it could also indicate a deeper electrical problem. If the new fuse doesn’t last long, have it inspected at an authorized Chevrolet service center since you may have a deeper problem in the electrical system.

What to do if your dash light does not work?

#Test the dashboard light bulbs. If the fuses are working properly, check for a blown bulb in the dashboard. Following the manufacturer’s instructions, disconnect the battery while working on the dash, remove the faceplate covering your vehicle’s dashboard gauge panel. Remove the screws holding the plate on. Carefully remove the faceplate.

What causes the dash light to go off on a PT Cruiser?

So far we had 3 pt cruisers with the same problem at the shop. When you drive the car and your dash light come on & off and the speedometer and tachometer quit working for a few seconds and then come back it is caused by the wires that go in the ignition switch.

#Test the dashboard light bulbs. If the fuses are working properly, check for a blown bulb in the dashboard. Following the manufacturer’s instructions, disconnect the battery while working on the dash, remove the faceplate covering your vehicle’s dashboard gauge panel. Remove the screws holding the plate on. Carefully remove the faceplate.

What are the lights on the dash on a PT Cruiser?

Chrysler PT Cruiser Dash Lights Instrument Cluster lights ON & OFF Blinking COMMON PROBLEM! – YouTube If playback doesn’t begin shortly, try restarting your device.

What to do if your YouTube gauges are not working?

Easy fix. How to reset. – YouTube Gauges not working? Instrument cluster not working ? Easy fix. How to reset. If playback doesn’t begin shortly, try restarting your device. Videos you watch may be added to the TV’s watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer.

When do dash lights come on and gauges drop to zero?

Dash lights came on and gauges dropped to zero gasoline w… When driving, occasionally all the dash lights will come on, but the gauges like gas, battery, and mileage, will all drop down to zero. Then my radio shuts off. Fortunately, the car keeps driving. All of this happened today, at a busy intersection, right before a stop light.

What happens when all the dash lights come on?

When driving, occasionally all the dash lights will come on, but the gauges like gas, battery, and mileage, will all drop down to zero. Then my radio shuts off. Fortunately, the car keeps driving. All of this happened today, at a busy intersection, right before a stop light.

With the ignition on, the gauge should register cold. If you connect the sending unit wire to ground, the gauge should switch to read hot. If the gauge moves as expected, then you can suspect a bad sending unit. If the gauge doesn’t move when you ground out the sensor wire, then you can suspect a bad gauge.

Why are the gauges on my boat not working?

Since none of the gauges are working (I assume so unless the tach is working, which is the only gauge you didn’t mention) then I would think it could be a power or grounding problem. Try climbing under the dash and making sure the two plugs on the MDC are seated well and make sure the cannon plug at the back of the engine is seated as well.

What to do if your gauge cluster is not working?

Since they are all giving you trouble, then I would recommend pulling the dash fascia out and getting your hands on that gauge. Trace the cable out through the panels and anywhere there is a connector pull and re-seat it many times to use friction to scrape clean corrosion off the leads and get a better connection.

Why is the gauge cluster on the dash?

Pulled the dash, unscrewed the cluster, left the two giant harnesses plugged in, unhooked the gear position needle and flipped that cluster up on the dash to have at it….bad move. My theories; either i broke a foil on the pcb by applying tension to the harnesses i left plugged in, or the burnt out bulbs were burntout for a reason.

Why do my car gauges turn off and on?

Now the gauges turn off and on, is says damaged keys. Window wont come up, says pass door is open. Headlights flicker, turn signals dont work, inside lights come on and off, and now push start wont work. I can work on the mechanical but don’t know much on the electrical.

Why does my Ford gauge cluster stop working?

I am assuming the cluster is never the issue in the condition it continues to work koeo and you flexed the board, and it never stopped working in those conditions. If it is dead while running, voltage is killing it or THE CHEAPEST EASIEST FIX EVER IS NEEDED. read the next trouble maker.

What does it mean when your dash gauges stop working?

After a short period they jump back up or if I stop, shut it down and restart it all is fine, for a while. I also hear what sounds like a pressure relief valve releasing, and when the gauges are down and I am coming to a stop, it sounds like the tranny is grinding. No Warranty left and can’t afford the dealer prices.

What happens when your fuel gauge stops working?

All of a sudden my power windows, radio, and fuel gauge stopped working. I have checked all fuses and even replaced a sudden my power windows, radio, and fuel gauge stopped working..fuses… Vocational, Technical or Tra… 2004 Ford Escape with shift on column. Heard a pop. Smoke 2004 Ford Escape with shift on column. Heard a pop.

Why do I have trouble shooting my gauge cluster?

I have been trouble shooting my instrument cluster for months! My gauge cluster, windows, radio would all come and go as they pleased for any amount of time you can think of. Seconds, minutes or days. It would happen in every circumstance you can think of; key on engine off, engine running at idle, left turn, right turn, braking, or accelorating.

How can I Fix my Ford gauge cluster?

Also, red. I bought an led kit. Pulled the dash, unscrewed the cluster, left the two giant harnesses plugged in, unhooked the gear position needle and flipped that cluster up on the dash to have at it….bad move.

Why did my fuel gauge stop working on my explorer?

I hooked up a trailer that was wired incorrectly and it blew the trailer battery power fuse. At the same time, the fuel gauge seemed to st … read more Today, all the sudden, the fuel gauge, power windows and radio, all stopped working on my 2004 ford explorer. everything else seems to work fine.

Why are there no windows and no radio?

However, as a consequence, I’m left with no power to my windows, overhead interior lights, radio, and the dash gauges no longer work. The dash, still displays my air bag yellow symbol, because the wires are disconnected under the drivers seat, it blinks then stays on.

However, as a consequence, I’m left with no power to my windows, overhead interior lights, radio, and the dash gauges no longer work. The dash, still displays my air bag yellow symbol, because the wires are disconnected under the drivers seat, it blinks then stays on.

Now the gauges turn off and on, is says damaged keys. Window wont come up, says pass door is open. Headlights flicker, turn signals dont work, inside lights come on and off, and now push start wont work. I can work on the mechanical but don’t know much on the electrical.

I hooked up a trailer that was wired incorrectly and it blew the trailer battery power fuse. At the same time, the fuel gauge seemed to st … read more Today, all the sudden, the fuel gauge, power windows and radio, all stopped working on my 2004 ford explorer. everything else seems to work fine.

If the oil pressure, coolant, charge, or gas gauge doesn’t work or works erratically, the problem is in the gauge, wiring, or sender. Speedometers are unique in that some of them use physical cables instead of sensors, so a speedometer not working can also indicate a broken cable or stripped gear.

What to do if there is no power window?

Check the power window circuit breaker for voltage, key on. That circuit breaker is in fuse box, under right side of dash. Use a testlite to check for voltage. Test the terminals with the key on. If no voltage, you’ll have to check out the ignition switch.

Why are my gauges not working on my GMC Sierra?

Of course they couldn’t read it with a scanner when it wasn’t working, there was no communication on the Class2 data line. This isn’t something you’re going to fix poking and prodding, and you may even do more damage. The dealer is the best bet to diagnose this, it could by any of the dozen or so modules causing this problem or any of the wiring.

Are there any Windows gauges or interior lights?

Us too any solution. 2008 f150 ford. Also bulb. Now no windows gauges etc… Fuses look good and replaced. 8 people found this helpful. More than likely cluster fuse is bad I had the same problem and the guy said in the post above yours it was F 21 cluster fuse and it says cluster keep a lab in the manual that is it

First instinct would be a ground problem but from your description it sounds like a Class2 data line problem and not an easy fix without some advanced knowledge and a scantool.

What happens when the dashboard lights go off?

In thise case however, the dashboard lights would come on, then disappear and then come back on intermittently. I got off the highway and out of traffic and the lights went away.

Author Image
Ruth Doyle