What oil goes in a NV5600?
What oil goes in a NV5600?
The NV5600 takes a special lubricant, not gear oil. The Mopar part number is 4874464. Transmissions specific 5W30. 5W30 motor oil is not recommended.
How much oil does a NV5600 take?
The listed capacity is 5 quarts. Many guys here including myself fill it with 6 for better coverage. You can fill through the shift tower, or park on a side incline with the driver’s side uphill and use the fill plug to fit 6 quarts.
How many quarts does a NV5600 hold?
The NV5600 has a 4.75 quart fluid capacity, but we recommend adding an additional quart when filling for better lubrication to 6th gear, so we’d recommend you purchase 6 quarts total.
How do I check my NV5600 fluid level?
Place the truck on level ground. Open up the fill flug, it is something like a 17mm Hex I think… Put your finger in there and if you can touch the lube then it has enough. If it is low then you can go buy the penzoil stuff to bring it up to level.
Where is the fill plug on a NV5600?
Re: Checking/Changing Oil in NV5600 For checking the level there’s a plug (17mm allen I believe) on the driver side of the tranny. To drain I would remove the driver side PTO cover. While the cover is off reach inside and feel around for the magnet at the bottom.
Is the NV5600 a 6 speed manual transmission?
The NV5600 is a six speed manual transmission built by New Venture. In terms of its uses in the light duty diesel market, it was factory installed as an option in the 2000 through early 2005 model year Rams, replaced in mid-model year 2005 by the G56. Ultimately, the NV5600 is a highly sought after transmission due…
When did the NV5600 go out of production?
In terms of its uses in the light duty diesel market, it was factory installed as an option in the 2000 through early 2005 model year Rams, replaced in mid-model year 2005 by the G56. Ultimately, the NV5600 is a highly sought after transmission due to its overall integrity and replacement parts availability.
What kind of shaft does the NV5600 have?
Ultimately, the NV5600 is a highly sought after transmission due to its overall integrity and replacement parts availability. The transmission features a 13″ flywheel and 1-3/8″ input shaft, edging out the NV5600’s predecessor the NV4500 by a small margin that featured a 12.25″ flywheel and 1-1/4″ shaft.
Can a Cummins NV5600 be a con OFE?
Upgrade your stock NV5600 clutch to the Con OFE from South Bend for better holding and increased longevity! South Bend Clutch Street Dual Disc 00-05 5.9L Cummins NV5600 6 Speed SBC-SDD3250-6 119.00 South Bend Clutch SDD3250-6
What kind of oil does a Dodge NV5600 use?
AMSOIL manual Syncromesh 5W-30. The oil used in the NV5600 must meet MS9224 specifications. I have been using Penzoil Synchromesh in the 5 gallon pale. It is a LOT cheaper that way.
What kind of oil should I put in my NV4500?
The goal of this post is to present information to allow you to make the right selection for your needs. The NV4500 factory fill was Mopar Synthetic Manual Transmission Fluid SAE 75W85 GL4 Part# 4874459 for Dodge applications or AC Delco Synthetic Manual Transmission Fluid SAE 75W85 GL4 Part# 12346190 for GM applications.
Can a transmission fluid be changed in a Chrysler NV5600?
This is a simple, step-by-step procedure on how to change the fluid in your NV5600 transmission. While Chrysler recommends that the fluid never be changed in this particular transmission, I’m of the opinion that any fluid will either wear out or become too full of debris over time.
When did the Dodge NV5600 transmissions come out?
Guaranteed quality and correct parts supplied. You can see the entire line of products which we offer at www.midwesttrans.com. The NV5600 transmissions were used by Dodge in Ram diesel series pickup trucks starting in 1998 The NV5600 is an end loaded cast iron case and aluminum removable bell section 6 speed transmission.