What kind of differential do I need for a 2003 Ford Explorer?

Ford Explorer with 8.8” Ring Gear Mexico Built 2003, Rear Differential Rebuild Kit by SKF®. Designed utilizing the latest technology, this product by SKF features premium quality and will perform better than advertised. Perfect for… Ford Explorer with 8.8″ Ring Gear 2003, OE Solution™ Rear Ring and Pinion Bearing Installation Kit by Dorman®.

What’s the torque on the rear end of a Ford?

The torque for these bolts is between 30 and 45 foot-pounds. These bolts attach the ring gear to the differential case. The torque for these bolts is between 70 and 85 foot-pounds. A certain pressure — or preload — on the pinion bearing and spacer must be established.

What should the torque be on a diff cover?

Torque specifications vary depending on the material and grade of fastener, and the material of the diff cover itself. Follow the instructions that came with your cover, they will usually fall between 20-30 ft/lbs. ARB for example, recommends right around 25 ft/lbs for most applications.

What are the torque and backlash specs for Ring?

Ring gear set up data is ©Copyright Crawlpedia.com – Please provide a link back to this page when copying. Data is accurate to the best of our knowledge through 2013 and is offered as-is with no guarantee. Chrysler Axles- Gear Setup Torque and Backlash Specs:

How big is the rear axle on a Ford Explorer?

The exception is the 2002-2003 Ford Explorer Sport which still used the solid rear 8.8-Inch axle. Ford Aerostar: The 8.8-Inch axle was used in 2WD 4.0L Ford Aerostars, but the All-Wheel-Drive (AWD) Ford Aerostar was equipped with the 7.5-Inch axle.

What are the dimensions of a 2003 Ford Explorer?

2003 Ford Explorer Specifications EXTERIOR Wheelbase 113.8 Track f/r 60.9 / 61.2 Overall Length 189.5

What are the torque specs for a Ford Taurus?

Ford torque specifications TORQUE SPECIFICATIONS FORD/MERCURY/LINCOLN APPLICATION FT-LBS / ( N-m) AXLE SPINDLE NUT PROBE 174-235 (235-319) ALL OTHERS 180-200 (244-271 BRAKE CALIPER BOLT (PROBE) 58-72 (79-98) CONTROL ARM-TO-KNUCKLE NUT SABLE & TAURUS 40-55 (54-75) ALL OTHERS 37-44 (50-60) CROSSMEMBER-TO-FRAME BOLT

What’s the gear ratio on a Ford Explorer?

We are proud to offer this remanufactured Rear Differential for the 2012-2015 Ford Explorer SUV with Four Wheel Drive. This rear diff can be configured with either a 3.55 or a 3.73 gear ratio, depending on the stock configuration of your Explorer…

Do you need ABS on the rear of a Ford Explorer?

The factory made rear end assembly did include ABS on each side of the unit. In a regular scenario, you might need to swap more than just the ring and pinion gear inside the differential. The rear bearing assembly and its shims could be required on a routine installation.

Can a rear axle break in a Ford Explorer?

The Dana 35 or 30 IFS axles used in the front of the vehicle can break too. Knowing when to pull the rear end out and modify it is a learned skill. It takes years before some people develop a good DIY work ethic. Ford Motor Company is one of the brands we carry.

What do you call the rear axle assembly on a Ford Explorer?

(What you see below is a previous search for a Ford Explorer Rear Axle Assembly and does not include all the Rear Axle Assemblies in YOUR area.) This part is also known as Ford Explorer Rear Axle Assy; Ford Explorer Axle Assembly, Rr.

How big is the ring gear on a Ford Explorer?

A typical ring gear size is the 8.8. The shaft is normally a 31 spline. This ensures a correct fit on the right and left side. The independent rear suspension (IFS) was the technology utilized in all trim versions of this SUV. On this website, you can buy a used rear differential for Ford Explorer.

How much friction modifier do I need for rear differential?

The rear diff requires 3.5 pints of 75-140, and .25 pints of friction modifier for the rear end clutches. I like to add the friction modifier to one of the quarts of 75-140 to make it easier to get into the diff. The correct way to fill the rear diff is to remove the fill plug. Add 75-140 up to the bottom of the fill plug.

How much additive do I need for rear differential?

What kind of front axles are at Denny’s?

Denny’s Driveshafts offers a wide selection of 4×4 Front Axle Shafts and related parts for most of the popular GM 8.5 inch, D44, D50 and D60 front ends as well as others for CHEVY, GM, DODGE, FORD, JEEP and SCOUT four wheel drive front ends.

Where can I find the dimensions of an axle?

The dimensions and spline counts of each axle as well as universal joint part numbers can be found on each page. Please be sure to measure carefully before ordering. U-Joints, Seals, Ball Joints, Steering Knuckle Parts, Yokes, Nuts and more.

Where can I buy a Ford axle differential?

National Differential has Ford differentials for sale that will fit your Ford truck or SUV. We can even do differentials for your Mustang or other Ford vehicle. Don’t see the Ford axle or differential you need? Give us a call at (719) 725-1559 and we’ll take care of you.

How big is the rear differential on a Ford F-150?

We are proud to offer this remanufactured 8.8-inch Rear Differential for the 1999-2003 Ford F-150 Pickup Trucks with 12mm or 14mm wheel studs. Compatible with either two-wheel or four-wheel drive trucks.

What kind of differential do I need for a 2003 Ford Explorer?