What is torque specs for bolts?
What is torque specs for bolts?
US Recommended Bolt Torque
| Size | Recommended Torque | |
|---|---|---|
| Grade 2 | Grade 8 | |
| 7/8″ | 129 | 501 |
| 1″† | 188 | 764 |
| * Sizes from #4 to #10 are in lb-in. Sizes from 1/4″ up are in lb-ft. † Fine thread figures are for 1″-14. Grade 2, 5, and 8 values are for slightly lubricated bolts. |
What is the torque on a 10.9 bolt?
Metric Recommended Bolt Torque
| Bolt Diameter (mm) | Recommended Torque (Nm) | |
|---|---|---|
| Class 8.8 | Class 10.9 | |
| 10 | 55 | 75 |
| 12 | 100 | 135 |
| 14 | 160 | 215 |
What is the torque on a 6 mm bolt?
Typical maximum recommended thightening torques for metric bolts
| Size (mm) | Typical Maximum Tightening Torque (Nm) | |
|---|---|---|
| Property Class | ||
| M5 | 7.0 | 10.0 |
| M6 | 11.8 | 17.0 |
| M8 | 28.8 | 41.3 |
What should the torque be on a bolt?
Bolt Torque Charts These charts show suggested maximum torque values for threaded products and are intended only as a guide. Always refer to the manufacturers recommended torque values if possible. CDI Torque Products is not responsible for any application of torque or it’s consequences as a result of using this chart. Use at your own risk!
How much torque does a SAE grade 2 Bolt have?
SAE Grade 2 Bolt Size TPI Proof Load (lbs) 1 Clamp Load (lbs) 2 Tightening Torque (ft lbs) Galv+Waxed Galv Plain 1 ⁄ 4 20 1,750 1,313 7 5 ⁄ 16 18 2,900 2,175 14 3 ⁄ 8 16 4,250 3,188 25
What should the torque be on a CDI bolt?
Bolt Torque Specifications These charts show suggested maximum torque values for threaded products and are intended only as a guide. Always refer to the manufacturers recommended torque values if possible. CDI Torque Products is not responsible for any application of torque or it’s consequences as a result of using this chart.
What are the tightening torques for Imperial bolts?
The tightening torques below are for imperial US bolts with tension approximately 70% of yield strength. The values are for slightly lubricated bolts. For dry bolts increase the torques with approximately 30%. Sorry to see that you are blocking ads on The Engineering ToolBox!
What are the torque specifications for a metric bolt?
Metric Bolt Torque. If the bolt diameter is 5 mm, thread series is Coarse, ISO 898-1 Property Class is 8.8, then. Torque for Ecoguard Bolt is 4.0 Nm, Lubricated is 4.6 Nm and dry is 6.2 Nm.
What are the torque requirements for bolts?
The required bolt clamping force for a joint is 20000 lbs. The torque required for a 3/4″ dry steel bolt to achieve this tension can be calculated as. T dry = (0.2) (20000 lb) (0.75 in) = 3000 (in lb)
How do you calculate bolt tension?
Determine the tension force on the bolt. This can also be measured using a force transducer (again, if the value is not already known). Assume the tension force is 3 lbs. Subtract the preload force from the tension force. In our example, the tension force (2 lbs.) subtracted from the preload force (3 lbs.) gives 1 lbs.
What is the torque for bolts?
Different bolt sizes and grades have different torque specifications. For example, 6 mm bolts with a 10.9 grade have a maximum torque value of 10 foot-pounds, while the same-size bolts with a 12.9 grade have a maximum torque value of 12 foot-pounds. Consult your shop manual for the most precise listings.
