What is SOC load line calibration?
What is SOC load line calibration?
Load-Line Calibration, or LLC, is a BIOS setting found on most performance motherboards and applies additional voltage to your CPU under load to provide more stability while overclocking and compensates for high and low voltage fluctuations, to keep your voltage line to the CPU more stable.
How do I overclock Ivybridge?
Step #2 Overclocking the Memory: Memory Overclocking on Ivy Bridge is extremely easy to do. You have to overclock with the memory multiplier along with the base clock, best set at 100.00 MHz for air OC. If you want more fine gradual increases you might try increasing the base clock.
Where is load line calibration MSI?
Answer. It is under BIOS–OC–Digit All Power–Load Line Calibration.
What does CPU core ratio do?
CPU Core Ratio, or multiplier, determines the speed of your CPU. For example, a BCLK of 100MHz multiplied by a CPU core ratio of 45 would result in a CPU speed of 4,500MHz, or 4.5GHz. This setting can usually be changed per core or across all cores. CPU Core Voltage is the amount of power being supplied to the CPU.
Should I disable LLC?
No, you are 100% correct. If that’s all the increase in voltage to be Prime stable you should disable LLC, you have no need for it.
What is CPU PLL voltage?
The PLL voltage setting determines the voltage fed to the CPU’s phase locked loop section. The phase locked loop section generates the clock signals for different parts of the CPU that are clocked at different frequencies.
What is CPU load-line calibration MSI?
LLC, short for Load-Line Calibration, applies additional voltage, when needed, to the CPU to ensure a more stable vCore under load (closest to what you manually set), and minimize the gap between CPU voltage in idle and load. So LLC is the golden setting when looking for the perfect 24/7 CPU overclock.
What is CPU core ratio limit?
The “core ratio limit” is your CPU frequency multiplier. The base clock signal in your chipset is set at 100 MHz and the i5-4570 has a maximum allowable speed of 3.60 GHz (for a multiplier ratio of 36x.) You can change the speed of each core separately and your i5 has four cores.
Should I Enable CPU C States?
C state is used for power saving and when you overclock you use the maximum power of the CPU, constantly. So you would not want to use c state. Disable both, also manual vcore always, adaptive might do some adjustments you don’t want to happen. First off an overclocked processor does not use maximum power constantly.
Do I need AVX offset?
If all your pc is used for is games there’s no need for any AVX offset at all. Also the offset has reported issues, it not only drops the cpu speed, but also vcore voltages and this can and will cause instability in some systems, especially if vcore is barely into stable voltages.
What is PLL Overvoltage?
The CPU PLL Overvoltage allows for less clipping of that voltage. It can also reduce the lifespan of the CPU, but nothing noticeable. So those of you who think that increasing your PLL voltage will help with that setting, it really doesn’t.
What does load line calibration do on a motherboard?
Load-Line Calibration, or LLC, is a BIOS setting found on most performance motherboards and applies additional voltage to your CPU under load to provide more stability while overclocking and compensates for high and low voltage fluctuations, to keep your voltage line to the CPU more stable. Nothing ruins a party more quickly than instability.
Is it OK to increase the voltage of the Vcore?
You should not proceed to just apply the maximum voltage for the vcore, vtt, or system agent as you will heavily increase the temperature so much so that the CPU will throttle and can be damaged. Also if you start off with a higher temperature it is very hard to test stability, as you will probably be more unstable than if you used a lower VCore.
What should voltage be for SVID on Ivy Bridge?
SVID will stabilize the CPU to about 4.2 GHz but not beyond that, so you will need voltage increase above 4.2 GHz. If you want the best results you should disable power saving options like I have below, however if you want the CPU frequency to drop under idle conditions, you should leave them enabled.
What does Orange Line mean in load calibration?
Orange line. So, in the real world the voltage will under or overshoot as the CPU is asked to change it’s load. These over or under shoots are what causes instability and the overshoots, in particular, can be damaging.
