How to replace camshaft sensor in Dodge Ram 1500?

If playback doesn’t begin shortly, try restarting your device. I’m an Automotive and Heavy Duty Mechanic/ “Jack of All Trades” that likes to make videos about anything and everything of interest.

How to replace the knock sensor on a Dodge Ram 2500?

Please try again later. Replacing Crank Shaft Position Sensor on the 2004 Dodge Ram 2500 with 5.7 Hemi. You need a 10mm socket and a screw driver to get the red tab popped up on the clip. You will see the knock sensor in this video also.

What does p0016 stand for in Dodge Ram?

P0016 is know to occur in the Dodge Ram when the Crankshaft Position Sensor and the Camshaft Position Sensor are out of alignment by a certain number of degrees, or if there is a sensor issue. We’ll explore the symptoms and causes directly below. P0016 refers to which camshaft position sensor is out of time with the Crankshaft.

What happens when the camshaft position sensor fails?

Once your car’s computer detects a CMP sensor failure, it will trigger the engine light and store a diagnostic trouble code (DTC) in its memory (see the table below for common camshaft position sensor trouble diagnostic codes). As you may expect, the specific location of the camshaft position sensor varies by a vehicle’s make and model.

What kind of engine does a Dodge 4.7 have?

The Dodge 4.7L V8 engine, or also known as the Chrysler PowerTech V8, is a decent engine. It has respectable power (especially the 2008 version) and somewhat decent fuel consumption for a large engine.

What is the cooling system on a Dodge 4.7 engine?

To be clear, pretty much any engine will develop problems with its cooling system over its lifetime, so this isn’t a problem specific to the Dodge 4.7 engine, but it can develop over time. The engine’s cooling system consists of the water pump, the radiator, cooling fan, thermostat, hoses, and several other components.

Can a faulty camshaft sensor cause a knocking sound?

Question: Can a faulty camshaft sensor cause a knocking sound? Answer: No, a faulty camshaft sensor can’t cause a knocking sound unless it affects ignition timing. Question: Can a faulty camshaft sensor cause a P0300 code? Answer: A number of faulty components may trigger a P0300 code, including: a bad camshaft position sensor

What should the voltage be on a camshaft sensor?

After these checks, use a digital multimeter that can test either alternate current (AC) voltage or direct current (DC) voltage, depending on your particular type of camshaft position sensor. You’ll also need the correct electrical values for your particular type of sensor. You may find this information in your vehicle repair manual.

Where to buy the camshaft position sensor test?

Where To Buy The Camshaft Position Sensor. TEST 1: Testing The Camshaft Position Signal. TEST 2: Making Sure The CMP Sensor Has 5 Volts. TEST 3: Making Sure The CMP Sensor Has Ground. More 5.2L, 5.9L Dodge Ram Diagnostic Tutorials.

Can a bad camshaft sensor cause engine stall?

If you are experiencing a hard start situation, engine stalling, rough idle and getting an OBDII engine trouble code of P0340 or 0340 camshaft position sensor circuit malfunction, you may have a bad camshaft sensor. This step by step video shows how I checked and cleared the engine trouble code and replaced the faulty engine sensor. Loading…

How to replace ambient light sensor 14-19 Chevy Silverado?

If playback doesn’t begin shortly, try restarting your device. Videos you watch may be added to the TV’s watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer. 1A Auto offers high-quality parts online with fast and free shipping and thousands of how-to videos.

Where is the camshaft position sensor located on the 5.9?

My name isXXXXX’m a 16 Yr Dodge dealership technician and I will be helping you with your question today… The camshaft position sensor (CMP) is located below the fuel injection pump. It is attached to the back of the timing gear cover housing. Disconnect both negative cables from both batteries. Clean area around CMP. Remove CMP mounting bolt.

Where is the crankshaft position sensor on a Dodge Ram?

However, if you are up for the challenge, you can save some money doing it yourself. If this is the first time you attempt the fix, then this will be the most difficult part of the job. The sensor is located on the passenger’s side, rear of the block where the transmission meets the engine.

Can a bad camshaft sensor shut down an engine?

Without this information, the engine would not be able to function properly. Over time, the camshaft position sensor can fail, or become worn down, due to accidents or normal wear and tear. There are a few warning signs to watch out for before your camshaft position sensor completely fails and shuts down the engine, making replacement a necessity.

Is there a camshaft position sensor on my car?

If playback doesn’t begin shortly, try restarting your device. An error occurred. Please try again later. (Playback ID: dVH3r2v1vO2KAucg)

What kind of car is Dodge Ram 1500?

••••• My current builds featured: 2003 Dodge Ram 1500 4×4 (off-road/ overland rig) 2001 Honda CRV 4WD (camping/ overland rig) 1993 Subaru Impreza WRX GC8 (autocross/ weekend toy) 2005 Subaru Forester XT SG6 (daily driver) ••••• If you’re interested in sending me products to review, please feel free to contact me.

How is the camshaft position sensor used in an engine?

The Camshaft Position Sensor is an electronic device used in an engine to record the rate at which the camshaft is spinning. This information is used by the Engine Control Module ( ECM) to control ignition and fuel injection. The camshaft position sensor senses the retraction of camshaft (intake) to identify a particular cylinder.

Why is my crankshaft sensor on my Dodge Ram not working?

The information received by the sensor is used to control the flow of gas, and a damaged sensor can cause the Ram to idle or accelerate improperly. Park the 2003 Dodge Ram on a flat, level surface and set the parking brake. Pull the hood release lever located under the dashboard.

Where is the battery on a 2003 Dodge Ram?

Park the 2003 Dodge Ram on a flat, level surface and set the parking brake. Pull the hood release lever located under the dashboard. Open the hood, and secure it in place with the hood prop. Disconnect the negative battery cable on both batteries.

How is the camshaft position sensor a circuit?

Intermittent open in the ground circuit to the camshaft position sensor Intermittent open in the signal circuit to the camshaft position sensor Intermittent short to 5 volts in the signal circuit to the camshaft position senso

What causes an OBD code for a camshaft sensor?

Typically the causes for this code are: Intermittent open in the power supply circuit to the camshaft position sensor Intermittent short to ground in the power supply circuit to the camshaft position sensor Intermittent open in the ground circuit to the camshaft position sensor Intermittent open in the signal circuit to the camshaft position sensor

Is there a p0344 camshaft position sensor a circuit?

[b]2003 Dodge Ram 1500 5.7Hemi P0340 & P0344 codes [/b] I’m getting 2 codes for my truck P0340, P0344 On every thing I have read its telling me its a Cam Shaft Position Sensor problem (P0340) It also came up as (intermitton) also it came up on freeze frame it said (fuel system 1 open loop)I am r…

How to replace camshaft sensor in Dodge Ram 1500?