How to order replacement parts for a lull?

Easily order Lull replacement parts by searching for the part number above. Don’t know the part number? Find part numbers and descriptions in the manuals below, or give us a call at 1-920-668-8484 with your model and unit serial number and we’ll help you find and order the correct part.

When did JLG stop making lull forklifts?

The process takes just a few seconds of your time, and you will have the manual you need. Lull forklifts and telehandlers were made by JLG, but new production was discontinued in 2014. Learn more Need a forklift manual for a different forklift brand?

Where can I download the lull forklift manual?

Just click the link for the model you are looking for. Then download the PDF document to your mobile device or computer. The process takes just a few seconds of your time, and you will have the manual you need. Lull forklifts and telehandlers were made by JLG, but new production was discontinued in 2014.

Who is the manufacturer of the lull telehandler?

JLG will continue to provide support for Lull machines in the field with parts and service and manufacture the SkyTrak® and JLG branded telehandlers.

Is the JLG telehandler 644e-42 series no longer available?

Beginning in 2015, the Lull 644E-42, 944E-42, and 1044C-54 Series II will no longer be part of the JLG telehandler portfolio.

Where can I find the owner’s manual for a 944e?

OWNERS/OPERATORS MANUAL Model 944E-42 (S/N 0160003882 thru 0160037751) 3120039 B Printed in U.S.A. 3/09 OWNERS/OPERATORS MANUAL Model 944E-42 (S/N 0160003882 thru 0160037751) Keep this manual with the vehicle at all times.

How tall is a lull C-54 telehandler lift?

2012 Lull, 1044 C-54 Telehandler, 10,000 lb capacity, 54 lift height with 8 tower attachment for a total lift height of 62 , Enclosed cab with heat, 4… 2008 Lull, 1044C-54 Telehandler, 10,000 lb capacity, 54′ lift height, 4 wdr, 3 way steering, 48″ side tilt fork carriage, 48″ pallet forks, 80″ load t…

How to get a lull warranty registration form?

A Warranty Registration form must be filled out by the Lull Distributor, signed by the purchaser, and returned to JLGonce the product is sold and/or put into service. This report activates the warranty period, assuring that your claims during the warranty period will be processed promptly.

What to do if your clutch pedal keeps sticking to the floor?

Step 3: Grab a pry bar and push the slave cylinder pin back into its rest position The clutch pedal should return to its rest position as well. Push down on the clutch pedal and see if will return. If the pedal stays on the floor, then the slave cylinder may have an internal leak if there is no external leakage.

What causes the reverse spool end of a hydraulic cylinder to stick?

1. Check installation drawings. 2. Check parts and drawings. 3. Reverse spool end for end. CYLINDERS TROUBLE CAUSE REMEDY ERRATIC ACTION 1. Valves sticking or binding 2. Cylinder sticking or binding 3. Sluggish operation during warm-up period 4. Pilot control pressure too low 5. Internal leakage in cylinder 6. Air in system 1.

What should I do if my clutch fork is not engaged?

Use your flashlight to look up in the clutch area to see the position of the fork. If the fork is all the way engaged but the slave cylinder or cable is not engaged, then the clutch release bearing has failed or the clutch fork has broke.

How to install steering cylinder in axle housing?

1. Use a rubber ma llet in order to install steering cylinder assembly (2) into axle housing (3) . 2. Remove fitting (28) from axle housing (3) . Rotate the steering cylinder in the axle housing in order to align the oil passage in the steering cylinder with the boss on the axle housing. 3. 4. Install spanner nut (1) .

How to remove a steering cylinder from a car?

1. Install ring (12) and O-ring seal (14) onto guide (9) . 2. Install guide (10) onto cylinder rod (4) . 3. Install ring (11), and ring (13) onto guide (10) . 4. Install dust seal (21) , seal (15), seal (20), ring (19) and ring (18) onto cylinder assembly (2) . 5.

Can a threaded rod be used to repack a cylinder?

Repacking your Hydraulic Cylinder. A threaded rod can have the piston directly attached, or a nut, or a nut and bolt can hold the piston in place on the rod. When the rod is free from the cylinder housing, remove the piston from the rod. Keep the parts in order and take a photo to use later for reference if needed.

How to order replacement parts for a lull?