How much horsepower does a TBI fuel pump support?

First I start with a new Fuel pump, STOCK 75lph TBI fuel pump will only support about 230hp before the fuel pressure drops like a rock.

What should the idle speed be on a GM TBI?

Insert a T-30 size Torx driver into the Idle adjustment screw that is located behind the plug removed earlier. Turn the screw to adjust the idle speed to 650 RPM +/- 50 RPM. Turn off the engine and disconnect the negative battery terminal from the battery using a wrench.

Which is a better TBI pump Vortec or TBI?

Put the 1996 Vortec EP381 pump back in. MUCH better pump than the EP386 TBI pump. Now to the too much fuel. First check the number 3 and number 4 spark plug electrodes as those cylinders always run off a different injector. The coloring should match on these plugs.

Can you change the throttle body on a 350 TBI?

Modify the throttle body. This one pretty cheap but does require removing the throttle body. UTIMATE MODS . Stock 42mm TBI units flow around 450cfm which if you look at http://www.carburetion.com/calc.asp a stock 350 even with a cam upgrade to increase the powerband to 5500 rpms isn’t going to use much if any more than that stock throttle body.

What should the fuel pressure be on a TBI 350?

WRONG – tbi is 11 to 14 lbs pressure stock! A stock tbi injector can go up to about 30 psi though:flipoff2: TBI’s max out around 30 psi, operating pressures are lower. Pressures in the 50-70 range are common in the later model CSFI & CPI vortec engines.

How to test the fuel pump on GM TBI fuel systems?

One method involves removing the fuel filter and using an adapter, that has a Schrader valve on it, in its place. You then connect your fuel pressure test gauge to this adapter. The other method is to use an adapter between the throttle body assembly and the pressure line.

What are the symptoms of a bad fuel pump?

Symptoms Of A Bad Fuel Pump. Where To Buy The Fuel Pump And Save. TEST 1: Using Starting Fluid. TEST 2: Fuel Pressure Test With Gauge. Which And Where To Buy A Fuel Pressure Gauge. More GM 4.3L, 5.0L, 5.7L Tutorials. You can find this tutorial in Spanish here: Cómo Verificar La Bomba de Combustible en Los Sistemas TBI (at: autotecnico-online.com ).

Where is the throttle body fuel pump located?

As you’re already aware, the throttle body fuel injection system on your 1987 to 1995 4.3L, 5.0L, or 5.7L pickup (or SUV) uses a low pressure (12 PSI) electric fuel pump located in the gas tank.

What should the air flow be on a 350 TBI?

On the average 350, I like a intake runner in the 165-180cc range and I like my air flow at.500″ lift to be at least the 225cfm that a vortec head flows. Stock TBI head flows around 175cfm.

What kind of Head do I need for a 350 TBI?

Another good reasonably priced set of heads that will work nicely without special intakes on a TBI motor is a set of Summit Racing aluminum heads. Great flow number and stock TBI or aftermarket TBI intakes will bolt right on saving you some money. 50 state legal and better flow numbers than vortec heads.

What do you need to know about a 1988 k1500?

You require accurate information to find and fix the fault right away. Use our 1988 K1500 wiring diagram and other schematics as guides while you’re troubleshooting the problem or determining what you need to buy. And best of all, you’re already in the right place to find the electrical components to complete the job.

What are the specs for a TBI crate engine?

4. The cam in the TBI engine is just plain AWFUL. Specs on Stock TBI cam is .050″ tappet lift (intake/exhaust) is 165/175; and maximum lift with 1.5:1 rocker ratio (intake/exhaust) is .382/.402. I got those specs right off the Jegs website selling the new GM replacement TBI crate engines.

First I start with a new Fuel pump, STOCK 75lph TBI fuel pump will only support about 230hp before the fuel pressure drops like a rock.

What is the TBI code on a 1990 Chevy truck?

Consult a service manual or see below for any check engine light code definitions. You can use a late 80’s or early 90’s GM TBI definition. If you have access to a scan tool use a hook up for a 1990 350 cu. in. 5.7L Chevrolet truck. For some scan tools enter VIN 10th“L” 3rd“C” 8th“K”.

What kind of oil does a Kawasaki 4 stroke use?

We recommend you check the oil levels daily and always use Genuine Kawasaki 4 Stroke Engine oil. To make changing your oil fast, easy and clean, get yourself a Kawasaki Oil Drain Hose! Part# 51044-0902 . Use the quick reference chart below to find the right oil for your Kawasaki Engine fast.

On the average 350, I like a intake runner in the 165-180cc range and I like my air flow at.500″ lift to be at least the 225cfm that a vortec head flows. Stock TBI head flows around 175cfm.

What should the fuel pressure be on a 350 TBI?

From 370-440hp you need to bump the fuel pressure up on the 454 injectors to the 15-18psi to increase their flow rate to 100lb/hr.

What kind of scan tool do I need for GM TBI?

A scan tool can be used and set up for a GM TBI application to read the data, or to check for stored codes. Consult a service manual or see below for any check engine light code definitions. You can use a late 80’s or early 90’s GM TBI definition. If you have access to a scan tool use a hook up for a 1990 350 cu. in. 5.7L Chevrolet truck.

How to troubleshoot your TBI fuel injection system?

Troubleshooting your TBI Fuel Injection System Most of the problems encountered while installing your fuel injection system or after a time of operation are very simple. If your check engine light is on you more than likely have a hard fault meaning something is grounded out, unplugged, operating out of range or has gone bad. See

Where does the vacuum leak come from on a TBI?

There are instances where the vacuum leak is coming from the adapter plate used to attach the throttle body to the manifold. If this is the case make sure that the seal is positive between the manifold and the adapter plate; also between the adapter plate and the throttle body.