How do you replace a rear axle bearing?

How do you replace a rear axle bearing?

1. Remove the Rear Backing Plate.
2. Locate and Remove Pivot Pin Bolt.
3. Remove the Pinion Pin.
4. Remove the C Clip and Axle.
5. Remove the Axle Seal.
6. Remove and Install Axle Bearing.
7. Install the Axle Seal.
8. Reinstall the Axle.

When to replace rear axle bearings and seals?

After the axle has been removed inspect the bearing and seal surface to check for wear and scoring and replace if damaged. If this axle is worn you will see an obvious groove in this area. Do not reuse the axle at this point because the new seal and bearing will fail prematurely.

How do you replace rear wheel bearings in Toyota?

Place the new seal into the axle end, and carefully drive it in. For this seal, I found the front hub 2 1/8″ socket with a towel on the end was the perfect size to drive the new seal. Once the seal is seated, coat the lips of the seal with grease. Next, clean up the axle flange surface and replace the O-ring, or use gasket-maker instead.

How are axle bearings pressed onto the shaft?

When replacement is needed, often the axle bearings are pressed onto the shaft using special equipment and holding fixtures. Many auto parts stores will provide this service for free if the replacement parts are purchased at the store. You should also replace the axle seals at the same time.

How do you change wheel bearings on a General Motors car?

Reinstall the brake drums or rotors and calipers and rehang the wheels. Lift the vehicle off the stands and remove them. Slowly lower the vehicle until the wheels make contact with the ground and finish tightening the lug nuts in a star pattern. Finish lowering the vehicle and clean up your work area.

How do you remove axle bearings?

Removing the Axle Bearings Remove the trays and coverings that are in the way. Remove the tires. Remove the brake pads from the caliper, and then unbolt the caliper itself. Release the parking brake. Remove the disk rotor. Remove the axle bearings using the bearing replacement/removal tool.

How much does it cost to replace rear wheel bearings?

If the bearing is sealed, it can lead to more work such as replacing the hub as well; however, a permanently sealed bearing means they can last longer, oftentimes, as long as the car. For the parts alone, wheel bearings can cost anywhere from $20 to as much as $200.

How do you remove a wheel bearing?

Remove the wheel bearings from your car wheel. Place a ball of grease in the palm of one hand. You may want to wear a pair of rubber gloves to protect your hands. Push the bearing into the grease with your other hand. Push in the large end first so that the grease gets forced into the inner parts of the bearing.

How do you repair a wheel bearing?

Steps Park your vehicle on a flat surface. Use wheel chocks to secure wheels whose bearings you aren’t replacing. Loosen the lug nuts and lift the wheel using a jack. Unscrew the lug nuts and remove the wheel. Remove the brake caliper. Remove the dust cover, cotter pin , and castle nut. Remove the rotor. Unscrew the hub bolts and remove the old hub.

That old bearing retainer can be used to judge if the bearing is fully seated. Just take the C-clip and see if you can fit it in the groove on the axle. To get the old retainer off, pry it apart with a flat bladed screwdriver in the slot you cut into it with the cutoff wheel and slip it off.

How do you replace the axle on a Toyota Tundra?

I greased up the bearing, axle, and seal surfaces, placed the axle on the cement floor, slid the backing plate over the axle, then slipped that old bearing retainer onto the axle to protect the bearing inner race from the beating I was going to give the pipe. I also placed a large socket under the hub to protect the wheel studs.

What should I do if my rear axle is bad?

I put the rear end on jack stands, started the engine, put it in drive, then probed around the differential and axles using my mechanic’s stethoscope. I determined that the right rear bearing was bad.

How can I tell if my rear axle is fully seated?

A few whacks with a 20lb sledge hammer and the bearing was seated on the axle. That old bearing retainer can be used to judge if the bearing is fully seated.

How is a center support bearing attached to a rear wheel drive car?

On some rear wheel drive vehicles, the bearing block bolts thread into nuts that are solidly mounted or welded onto the frame. On some vehicles, two part nuts and bolts are used to attach the rear of the front driveshaft to the center support bearing.

What to do if your axle bearing comes out?

Using a axle bearing remover and a slide hammer that bearing will come out in a matter of seconds. if you have a bad axle bearing you should be able to hear some rear end noise while driving. anyways it’s beer time https://www.facebook.com/pages/Bullsh… Loading…

Can a Mercedes rear wheel drive axle be replaced?

Mercedes rear wheel drive axle/hub bearing replacement.. R170 shown..very long video If playback doesn’t begin shortly, try restarting your device. Videos you watch may be added to the TV’s watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer.

How do you remove a front drive drive bearing?

Step 1: Remove the front driveshaft. The front driveshaft is attached to the transmission output shaft and connected by four bolts. On some rear wheel drive vehicles, the bearing block bolts thread into nuts that are solidly mounted or welded onto the frame.

How are rear wheel bearings supposed to work?

Axle Repair Bearing Guide. Certain rear wheel bearings use the axle as an inner race; that is the bearing rollers ride directly on the axle shaft itself. At times, worn or pitted rollers, chipped or damaged bearings can wear a groove into the axle shaft.

What do rear axle bearings and seals look like?

The seals should look identical unless they have been updated by the manufacturer. Once the surface has been cleaned, match the new seal to the old unit and apply sealer to the differential housing if needed. Most seals have a sealer allied to them as a thin coating, this seal uses an orange colored sealer.

How does a SKF axle repair bearing work?

A cost saving approach offered by SKF is an axle shaft repair bearing. The axle repair bearing assembly replaces both the bearing and the conventional seal requiring no additional parts. The repair bearing moves the position of the bearing and seal so that they ride on an unworn section of the axle shaft.

When do you need to replace an axle shaft bearing?

(See Fig. 1) Over time, the seal may also wear a groove into the axle shaft. (See Fig. 2) When this occurs it’s usually necessary to replace the axle shaft assembly, bearings and seal. A cost saving approach offered by SKF is an axle shaft repair bearing.

How to replace a rear wheel bearing in your car?

Wheel bearing replacement. How to replace a rear wheel bearing in your car DIY with Scotty Kilmer. How to replace bad rear wheel bearing on the hub assembly. Rear wheel bearing location, inspection, removal and replacement. DIY car repair with Scotty Kilmer, an auto mechanic for the last 40 years. 1. Bearing Puller: http://amzn.to/2Ba7sjF 2.

How are rear wheel bearings used as inner race?

Certain rear wheel bearings use the axle as an inner race; that is the bearing rollers ride directly on the axle shaft itself. At times, worn or pitted rollers, chipped or damaged bearings can wear a groove into the axle shaft. (See Fig. 1) Over time, the seal may also wear a groove into the axle shaft. (See Fig.

When do you need to replace an axle seal?

At times, worn or pitted rollers, chipped or damaged bearings can wear a groove into the axle shaft. (See Fig. 1) Over time, the seal may also wear a groove into the axle shaft. (See Fig. 2) When this occurs it’s usually necessary to replace the axle shaft assembly, bearings and seal.