How do you change the pinion seal on a Ford?
How do you change the pinion seal on a Ford?
Pry out the old pinion seal with a seal removal tool or a small pry bar. Wipe the area on the axle housing around the pinion seal with a shop rag. Apply a light coat of oil to the inside rubber part of the new gear oil seal. Apply a light coat of gear oil to the outside of the new pinion seal.
How to change your rear main seal-YouTube?
In this video, we show you how to change your rear main seal. When this seal goes bad, it can cause oil to start leaking out from the back of the engine, and has to be replaced. You can now get your very own budget boosting window sticker! Click the link below and you will be taken to our eBay page! http://www.ebay.com/itm/251593397621?…
How do you replace a rear end seal on a Ford?
Pull the drive shaft away, then bend the coat hanger around the drive shaft and hang it from the frame off to the side so it does not rest on the ground. Use your screwdriver to lever the pinion seal out of the differential, again being careful not to score or otherwise damage the sealing surface.
How to replace a rear main seal without removing the hood?
The flex plate is the last layer that covers rear main seal replacement. By removing the flex plates you will be able to unbolt the seal from the rear end. 3. Remove the Rear Main Seal Hood Now that you have taken away all the supplementary parts, it is time to remove the rear main seal.
Pry out the old pinion seal with a seal removal tool or a small pry bar. Wipe the area on the axle housing around the pinion seal with a shop rag. Apply a light coat of oil to the inside rubber part of the new gear oil seal. Apply a light coat of gear oil to the outside of the new pinion seal.
Pull the drive shaft away, then bend the coat hanger around the drive shaft and hang it from the frame off to the side so it does not rest on the ground. Use your screwdriver to lever the pinion seal out of the differential, again being careful not to score or otherwise damage the sealing surface.
How do you change a pinion nut on a Ford?
Remove the bolts on the U-straps that hold the universal joint onto the pinion yoke. Remove the straps. Remove the universal joint and the driveshaft from the yoke and lower the driveshaft to the ground. Be careful that the caps on the U-joint do not fall off. Place an inch-pound needle-type torque wrench and socket on the pinion nut.
What to do if rear axle pinion bearing cup is damaged?
Inspect rear axle pinion bearing cups. If damaged, remove from rear axle housing by tapping alternately (with a brass drift of suitable length) on each side of rear axle pinion bearing cups to prevent rear axle pinion bearing cups from cocking in rear axle housing bore.
How do you get the tail bearing out of a Ford?
Knock out the pinion seal to get the tail bearing out with a hammer and punch from the back side. When these parts have been pressed apart, the basic arrangement of the parts looks like this.
Remove the bolts on the U-straps that hold the universal joint onto the pinion yoke. Remove the straps. Remove the universal joint and the driveshaft from the yoke and lower the driveshaft to the ground. Be careful that the caps on the U-joint do not fall off. Place an inch-pound needle-type torque wrench and socket on the pinion nut.
Is the pinion head still pressed on the shaft?
The pinion head bearing is still pressed on the pinion shaft. You can see the stock collapsible spacer sitting on the splines. The bearing races or cones are still pressed into the cartridge. Knock out the pinion seal to get the tail bearing out with a hammer and punch from the back side.
How do you replace front pinion seal?
Slide the pinion yoke off the pinion shaft and set it aside. Using a small flat screwdriver, bend the outer metal ring of the seal to help loosen it then pry it out of the bore. Pack the cavity behind the seal with lithium grease then install the new seal into the bore.
What is a rear differential pinion seal?
The pinion seal is located near the pinion shaft and is designed so that fluid does not leak out of the differential. Some vehicles have a rear pinion seal, where others have both a front and rear pinion seal, it just depends on the make and model of your vehicle and if the vehicle has rear or four wheel drive.
What is pinion seal?
A pinion seal is a component within your car differential that is meant to keep the differential fluid from leaking out of your car. The pinion seal is found near the pinion shaft, just between the differential pinion gear and the pinion shaft flange.
