How do I setup my HP ProCurve Switch?

How do I setup my HP ProCurve Switch?

How to: Configure a HP ProCurve switch

1. Step 1: Connect your serial connection.
2. Step 2: Conenct PuTTY.
3. Step 3: Get the IP address.
4. Step 4: Set time server.
5. Step 5: Set SNMP community info.
6. Step 6: Launch the web GUI.
7. Step 7: Configure basic info.
8. Step 8: Create VLANs.

How do I find the interface configuration on an HP switch?

You can use the options with the startup config command, show config, and the running config command, show running-config.

Does HP still make ProCurve switches?

HP ProCurve was the name of the networking division of Hewlett-Packard from 1998 to 2010 and associated with the products that it sold. The name of the division was changed to HP Networking in September 2010.

How do I change the speed duplex on an HP switch?

Enabling or disabling ports and configuring port mode (CLI)

1. You can configure one or more of the following port parameters.
2. To configure port C5 for auto-10-100, enter this command: HP Switch(config)# int c5 speed-duplex auto-10-100.

How do I assign an IP address to my HP Procurve Switch?

HP Procurve Switch # [Tab] to the IP Config (DHCP/Bootp) field and use the Space bar to select the Manual option. [Tab] to the IP Address field and enter the IP address that is compatible with your network. [Tab] to the Subnet Mask field and enter the subnet mask used for your network.

How do I configure my HP Procurve Switch to 1800 24G?

HP ProCurve 1800-24G Switch – Installing the Switch

1. Installation precautions.
2. Prepare the installation site.
3. Verify the switch passes self test.
4. Mount the switch.
5. Connect the switch to a power source.
6. Connect the network cables.
7. Installing or Removing mini-GBICs.

How do I access the HP Procurve Switch web interface?

Verify the configuration Enter https://10.1.1.1 in the address bar, and select the certificate issued by new-ca. Then the web login page of the Device appears. On the login page, type the username usera, and password 123 to enter the web management page.

How do I configure my HP switch interface?

To configure the management Ethernet interface follow the steps given below:

1. Enter system view and use the command.
2. Enter management Ethernet interface view and use the command.
3. Change the description of the interface and use the command.
4. Shut down the interface and use the command.

What happened HP ProCurve?

HP ProCurve was the name of the networking division of Hewlett-Packard from 1998 to 2010 and associated with the products that it sold. The name of the division was changed to HP Networking in September 2010 after HP bought 3Com Corporation.

What does a HP ProCurve Switch do?

The HP ProCurve Switch 2224 will auto-negotiate half or full duplex, except for the 100Base-FX Transceiver Module. If a full-duplex auto-negotiating device is connected to the switch, it chooses full-duplex. Note that the device connected to the HP ProCurve Switch 2224 must be compliant with the IEEE 802.3u standard.

How do I access my HP Procurve console port?

To connect a console to the switch, use the console cable shipped with the switch and connect a PC or VT-100 terminal to the console serial port….

1. Reconfigure the switch and save the new settings.
2. Reconfigure the terminal and save the new settings.
3. Reboot the switch and re-establish the console session.

How do I find the IP address of my switch?

Complete these steps

1. Select the Start button located in the bottom left corner.
2. Type Run into the Start Menu search and press Enter.
3. Type CMD and press Enter.
4. Type ipconfig/all and press Enter.
5. Your network’s IP information should now be displayed in a list.

How to configure a HP ProCurve switch?

How to: Configure a HP ProCurve switch Step 1: Connect your serial connection. Connect to the console port of your switch via a serial cable. Older switches… Step 2: Conenct PuTTY. It’s just a standalone .exe with nothing to install. Run PuTTY, and select the ‘serial’ radio… Step 3: Get the IP

Is the HP ProCurve switch a registered trademark?

Publication Number 5967-6967 December 1998 Applicable Product HP ProCurve Switch 4000M (J4121A) HP ProCurve Switch 2424M (J4093A) Trademark Credits Microsoft, Windows, Windows 95, and Microsoft Windows NT are registered trademarks of Microsoft Corporation. Internet Explorer is a trademark of Microsoft Corporation.

What kind of serial port do I need for HP switch?

Older switches such as the 2900-48G’s have a 9 pin serial connector on the back of the switch, newer switches have an RJ-45 connection on the front and use a serial> RJ-45 cable. If your laptop does not have have a serial port, you can use a USB-serial adapter.