How do I read computer codes on a 1997 Chevy truck?

Reading the engine codes on a 1997 Chevy truck was standardized with the implementation of on-board diagnostics 2 (OBD-II) in 1996. This allowed repair stations and dealership service centers to use the same equipment and the engine codes for most all vehicles.

Where is the trouble code on a GMC?

When retrieving GMC trouble codes with an OBD II scan tool, proceed as follows: 1. Connect scan tool to the 16-pin data link connector (DLC) located underneath the steering column. The connector may have a removable cover. 2. Turn the ignition on.

Why does my GMC Sierra 1500 run rough at idle?

The spray smoothing out the rough rpm is an indication of the engine running lean, could be low fuel pressure, could be a vacuum leak. With it running rough at an idle and smoothing out at a higher rpm is a general sign of a vacuum leak.

What are the codes for GMC check engine lights?

P1245Intake Plenum Switchover Valve P1250Early Fuel Evaporation Heater Circuit P1257Supercharger System Overboost P1258Engine Coolant Overtemperature – Protection Mode Active P1260Last Test Failed SCC Or Theft Detected, Vehicle Immobilized

How to troubleshoot a misfire ( GM 4.8L, 5.3L )?

Engine Mechanical: Misfire Troubleshooting. You can find this tutorial in Spanish here: Cómo Diagnosticar y Resolver Una Falla en Cilindro (GM 4.8L, 5.3L, 6.0L) (at: autotecnico-online.com ). The core symptom of a misfire is rough idle.

Which is the diagnostic code for a GMC check engine light?

1 Refer to our Generic OBD II code list for definitions on all other GMC diagnostic trouble codes. 2 Manufacturer Specific Codes 3 P1031 4 P1032 5 P1105 6 P1106 7 P1107 8 P1108 9 P1109 10 P1111

What’s the idle RPM on a 99 Vortec?

Truck recently had an exhaust manifold replaced. When its cold (as in first thing in the morning), it fires right up and high-idles for a few seconds and runs fine. After the first few seconds, its idles rough. The engine struggles to keep it above 7-800 RPM.

What is the diagnostic code for a Chevy check engine light?

Remember, these are manufacturer specific codes only. Refer to our Generic OBD II code list for definitions on all other Chevy diagnostic trouble codes. Manufacturer Specific Codes P0342Camshaft Position Sensor A Bank 1 Low Input – Related Information P1031HO2S Heater Current Monitor Control Circuit Sensors 1

What is the oxygen sensor code for a Chevy?

P1137HO2S Bank 1 Sensor 2 Lean Or Low Voltage – Read Our Article On Oxygen Sensor CodesFor Help With This Chevy Trouble Code P1138HO2S Bank 1 Sensor 2 Rich Or High Voltage – Read Our Article On Oxygen Sensor CodesFor Help With This Chevy Check Engine Light Code

What does code23 on check motor light mean?

Let’s say, Code23 would be like a pulse – pulse – pause – pulse – pulse, and – pulse. In this stage, you need to note down the code as it flashes in your vehicle’s check motor light because each code would come together and help you in understanding the issue in a proper way.

How do you turn off a check engine light?

If you don’t get a definition, look up the code in the owner’s manual or online. Press the “erase/clear” button on your scanner, then turn off the key and disconnect it. Clearing any codes present will turn off your check engine light temporarily.

Why is the Check Engine light on on my car?

The vehicle is emitting emissions which are higher than the Environmental Protection Agency mandates, and that is why the check engine light is on. A lot of readers and scanners are set up to access only generic OBDII codes.

What kind of problem does a 1997 GMC pick up have?

1997 GMC K1500, K2500, K3500 Pick Up. All of the information you need to diagnose a misfire or a no-start problem (caused by the ignition coil, the ignition module, or the crankshaft position sensor). Wiring diagrams.

What was the ignition module for a 1996 GMC k1500?

1996 GMC K1500, K2500, K3500 Pick Up. All of the information you need to diagnose a misfire or a no-start problem (caused by the ignition coil, the ignition module, or the crankshaft position sensor). Wiring diagrams.

Where is the DLC outlet on a 1997 Chevy truck?

All 1997 Chevy truck models positioned the DLC on the lower side of the dashboard to the left of the steering column. Attach the trapezoid-shaped plug of the pocket scanner to the DLC outlet. Because of its shape, there is only one proper way to connect the plug to the DLC.

What’s the engine code on a 1997 Chevy truck?

While there are several hundred engine codes, all OBD-II codes under 900 are generic while any over 900 are vehicle-specific; geared towards that year, make and model. OBD-II also equipped vehicles with the exact same data/diagnostic link connectors, so the same scanners can be used for all vehicles.

What are the misfire codes for GM 4.3L?

P0303 Cylinder #3 Misfire. P0304 Cylinder #4 Misfire. P0305 Cylinder #5 Misfire. P0306 Cylinder #6 Misfire. P0307 Cylinder #7 Misfire. P0308 Cylinder #8 Misfire. Sometimes, even tho’ the engine is suffering a bona-fide misfire, no misfire codes are registered in the computer’s memory and/or no check engine light (CEL) on.

Can You Check Engine codes without a code reader?

Checking engine codes without code reader is helpful when you don’t have a car code reader or you forgot your car code reader.

What does code 12 mean on GM OBD?

The system will enter the diagnostic mode. In this mode, the computer will display a Code 12, three consecutive times, by flashing the “CHECK ENGINE”, “SERVICE ENGINE SOON” or “MALFUNCTION INDICATOR LAMP” or light. A Code 12 consists of one flash, a short pause, then two flashes in rapid succession.

How to read a GM check engine light code?

It will look like Morse Code, but it isn’t, and is real easy to interpret. The first code that will flash will be a code 12. It will be “flash, pause, flash, flash, pause, pause,” and repeat the cycle three times. The ECMwill flash each code three times, and move on to the next. If you have no codes stored, it will keep flashing code 12.

What is the DTC code on a check engine light?

Diagnostic trouble codes (DTC) are automotive computer codes stored by the on-board computer diagnostic system (OBD) in your vehicle. There are literally hundreds of different codes a Check Engine Light can represent.

Checking engine codes without code reader is helpful when you don’t have a car code reader or you forgot your car code reader.

How do I read computer codes on a 1997 Chevy truck?