How big is the flexplate on an AOD transmission?
How big is the flexplate on an AOD transmission?
The AOD takes a 164-tooth AOD-specific flexplate instead of the smaller 157-tooth pieces common to the C4 and early Ford manual transmissions. Because the AOD is longer, the crossmember must position the mount farther to the rear of the vehicle to support the transmission.
What kind of flexplate do I need for my Ford 4R70W?
You replace it with the 164-tooth flexplate for the AOD/AODE/4R70W, which is also a 28-ounce offset balanced. Note the type of engine you have also determines the flexplate type. Small-block Ford V-8s, which are externally balanced, are either 28- or 50-ounce offset balanced.
Where is the transmission adaptor on a Ford Big Block?
Adaptor kits are available for both the FE- and 385-series Ford big-blocks. Keep in mind these adapter kits alter the transmission mount location by 1 to 2 inches toward the rear of the vehicle.
What are the parts for a Ford F150?
We strive to provide our OEM Ford F150 Parts for All trims quickly. If Parts are in stock they sometimes ship same day. Other Names: Shackle Nut, Mount Bracket Nut, Lower Control Arm Nut, Lower Arm Nut, Trailing Arm Nut, Upper Arm Nut, Mount Bolt Nut, Link Rod…
The AOD takes a 164-tooth AOD-specific flexplate instead of the smaller 157-tooth pieces common to the C4 and early Ford manual transmissions. Because the AOD is longer, the crossmember must position the mount farther to the rear of the vehicle to support the transmission.
How to change the AOD transmission in a Ford?
Disconnect the driveshaft, shift, and kickdown linkages. Have a solid means of support beneath the transmission. Remove the dust cover to get at the torque converter and flexplate. Remove the torque converter fasteners with a 5/8-inch socket. Rotate the engine crankshaft to get at hard-to-reach fasteners.
How big is a flexplate for an integral bellhousing AOD?
Flexplate Diameter and Balance- One of the more important parts of the swap is to choose the proper flexplate for your application. The integral bellhousing AOD requires a flexplate with 164 teeth (approximately 14 1/4 diameter with an 11 7/16 torque converter bolt pattern) for proper starter placement and converter compatibility.
Do you need a dust cover for an AOD transmission?
The AOD and C4 transmissions use different block plates primarily because they are different transmissions with two different-size flexplates. This means you need an AOD-specific block plate and dust cover for the 164-tooth flexplate.
What kind of transmission does a 302 Ford have?
We are offering 302 Ford – 350 HP with AOD 4 Speed Transmission Kit at a very competent price, please check the Product specifications and if you have any questions feel free to contact us. ELECT. BILLET IGNITION DISTRIBUTOR W/ 45,000 VOLT COIL
Disconnect the driveshaft, shift, and kickdown linkages. Have a solid means of support beneath the transmission. Remove the dust cover to get at the torque converter and flexplate. Remove the torque converter fasteners with a 5/8-inch socket. Rotate the engine crankshaft to get at hard-to-reach fasteners.
Is the C4 164 teeth flexplate compatible with AOD?
The C4 164 teeth flexplates and the AOD 164 teeth flexplates will physically interchange, but there are two balance weights to be concerned with. Part# OEM E0AZ-6375-A (164 teeth flexplate, 28.2 oz-in balance factor, 351W with AOD applications).
Is the 1986 Ford F-150 4 wheel drive?
1986 F150 – 4 wheel drive. The #1 volume chrysler dealer in western kansas and eastern colorado. 1986 For F150. It needs the heads put back on. It was running great, before it 1,000 1986 For F150. It needs the heads put back on. It was running great, before it It needs the heads put back on. It was running great, before it blew the head gaskets.
What kind of transmission do I need for a Ford Mustang?
The most common transmission swap with older Fords is from a C4, C6, or FMX to an AOD or manual 5-speed. The focus here is putting a Ford AOD into a classic Mustang and other vintage Ford applications, which are the more common swaps.
What kind of transmission do I need for Ford AOD?
You can copy and paste this link to share: https://www.diyford.com/ford-aod-transmission-installation-and-swapping-guide/ The most common transmission swap with older Fords is from a C4, C6, or FMX to an AOD or manual 5-speed.
When did the Ford AOD transmission come out?
The AOD transmission is a Ford model that was introduced in 1962 aimed at emphasizing fuel economy and durability. While many transmissions of the time had a fourth gear installed as a basic afterthought only there for minimal purpose, the AOD was designed as having the fourth gear as an integral part…
How to adjust throttle cable on Ford AOD transmission?
Have someone floorboard the accelerator pedal from inside the vehicle. While the pedal is floored, push on the throttle body arm to make sure it’s bottomed against its stop (wide open). (Adjust throttle cable, if necessary). 3. While the throttle is floorboarded, lock the tab on TV adjuster. 4.
What happens when you add TV to AOD transmission?
Adding TV to attempt to correct pinging, chugging or lugging won’t work. It Just causes thumps, bumps and extra wear. Set the TV so that the shifts are smooth and not late. IMPORTANT: The AOD transmission may feel like it is shifting at the right time when the TV cable is actually way off! The transmission will work for a while and then FAIL!
