Can you go from SATA to Molex?

Can you go from SATA to Molex?

Features : For Hard Drive , The LP4SATAFM12 SATA to LP4 Power Cable Adapter enables you to power 4-pin Molex devices (i.e. hard drive, DVD-ROM drive, add-in card, etc.) from a SATA power connector on your computer power supply.

Can you use Molex to SATA for hard drive?

A Molex to SATA connector should be fine for most HDDs and DVD Drives but it may not be sufficient for more modern SSDs and BluRay drives. The SATA power connector includes a 3.3 volt rail as well as the traditional 5 volt and 12 volt rails.

What is the function of Molex to SATA adapter?

The Cable Matters 4-Pin Molex to SATA Power Cable Adapter is a handy addition to your toolbox when building, upgrading or repairing computers. It connects newer SATA internal hard drives, optical drives, and motherboards to a power supply with legacy LP4, 4-pin Molex connectors.

Does Molex provide more power than SATA?

Technically Molex can carry much more power than the SATA power connector. Molex has 2 power pins (one 5V and on 12V pin), each can deliver 11Amps for a total of 22Amps. The other 2 pins are ground wires… SATA power connectors has a total of 15 pins of which 9 are power pins (3 x 3.3V, 3 x 5V, 3 x 12V).

Is 2 SATA to Molex safe?

Perfectly safe. You are powering fans. They only need the two lines you are giving them.

What is a LP4 connector?

The LP4SATAFM12 SATA to LP4 Power Cable Adapter enables you to power 4-pin Molex devices (i.e. hard drive, DVD-ROM drive, add-in card, etc.) from a SATA power connector on your computer power supply. Offering 12 inches in cable length, the cable allows you to position your devices as needed within the system case.

What is wrong with Molex SATA?

Molex to SATA adapter cables are a very simple and cost-effective alternative to buying a new power supply. However, they can be a dangerous alternative to getting a quality power supply, potentially damaging your SSD, internal components, and may also pose a fire risk in your home.

Can I use Molex to power SSD?

With a simple molex connection, you can attach up to 4 SATA devices. That’s enough for an SSD, an HDD, and a Blu-Ray drive, with an extra plug left over for later expansion.

How can you differentiate between a Molex power connector and a SATA power connector?

The big difference between the SATA power cables and the Molex adapted SATA power is that the Molex connectors only supply 12V and 5V, while the SATA power cables supply 12V, 5V, 3.3V (orange).

What type of device would you connect a Molex cable to?

Certain Molex connectors are used for providing power to the motherboard, fans, floppy disk drive, CD/DVD drive, video card, some older hard drive models, and more. Compatible connectors are available from many manufacturers, not just Molex and AMP.

What is the purpose of a Molex cable?

Molex cables are primarily used for power-supply units, or to connect power-supply units to hard drives, as with the Molex-to- SATA power cable shown below.

Does the PSU come with Molex connectors?

Completely obsolete, but some PSU’s still come with a mini-molex connector. These guys were used to power floppy disk drives. For those of you who do not remember; these were square magnetic disks that could contain up to 1.44 MB of data. Basically they were superseded by the USB stick.

How many pins does a SATA power cable have?

The SATA data cable that transmits the data between the drive and the motherboard has seven pins. The SATA power cable that connects to the power supply has fifteen pins.

What is the voltage of Molex?

A Molex connector’s red wire should be at 5 volts. The yellow wire should be at 12 volts.