Are there any low beams in my truck?

The truck used to have HIDswhen I bought it, I took them out and put the stock bulbs back in, they a re about 2 months old and the fuses are good. The DRL and high beams work fine. What could be wrong? I don’t want to just throw money and parts at it so any advice would be appreciated !

Is there no power to the low beam headlight?

The wires connecting to the bulb are also clean and the factory harness itself is clean. So with the headlights on and selector in lowbeam position, you have power to the low beam headlight connector. No no power to the connection at the bulb.

Where is the low high beam headlight dimmer switch?

As mentioned at the beginning of the article, the Low-High Beam Headlight Dimmer Switch is part of the Turn Signal Assembly. If you have already taking the steering column covers off, you’ve noticed that the turn signal switch has a lot of wires connecting to it.

What should the low and high beams be aimed at?

Low beams should be aimed straight forward and hit no higher than your hood line. The high beams should move slightly, but not too much higher than the low beams. If they need to be adjusted, there are screws on the back or top of the housing to allow you to do so.

What kind of noise does a Chevy 4.3 make?

by Contributor. A common complaint with the Chevy 4.3 engine is that it doesn’t idle well, it’s loud and makes awkward noises. Examples of this are staling, lurching and poor acceleration. Poor idling and loud engines usually go hand-in-hand.

Are there any problems with the Chevy 4.3 Vortec engine?

The 4.3 Vortec engines made from 1996-2002 (L35 and LF6) have been reported to have engine knock problems. In a properly functioning engine, fuel burns in even pockets instead of all at once. The pockets burn in even timing, in sync with engine cycles. Engine knock occurs when the fuel burns unevenly and out of sync with the engine cycles.

What does Vortec stand for in Chevy engine?

The term “vortec” is simply a marketing name used by Chevrolet to communicate its use of “vortex technology”. Chevy’s vortex technology creates an air vortex inside the engine, which results in better air-to-fuel efficiency.

What makes the low beams stay on in a Silverado?

I assume it’s splicing the tan lo beam wire to the yellow headlight feed wire just before the dimmer switch so that the lo beams stay on when the high beams are turned on? (I have the composite headlights.)

Why are my low beam headlamps not working?

The Problem: Low beam headlamps not working. (Sometimes) I own a 2001 Tahoe and am having a problem with the low beams. Sometimes they just decide not to work. It’s like the truck is haunted. Its night. I get in, turn the key on (before I actually start it) and no headlamps.

How to check if a low beam light is working?

Unplug the harness from both low beam bulbs and with the selector in low beam position check for battery voltage with a digital multimeter. Ok so I got around to testing and the relay and fuses are working and there is powering getting to the relay for it to click between on off and running lights. There is no power getting to the bulb.

Are there low or high beams in my truck?

I turn the switch to turn them on manually… no headlights. The weird thing is everything else is on and working properly. Dash lights, parking lights, taillights… everything. I hit the dimmer switch and the highs come on. Hit it again, and no low beams. Next day I get into the truck and everything works fine. Low and high beams work. (night time)

What should I do if my Chevy headlights are not working?

To check alignment, park about 10 feet from the garage door wall and turn the lights on. Low beams should be aimed straight forward and hit no higher than your hood line. The high beams should move slightly, but not too much higher than the low beams.

How can I tell if my low beams are working or not?

The same lever that switches between lows and highs and for turn signals. If you’re in front of a wall or in your garage and pull the lever you can see that all come on while the lever is pulled back if the engine is running and the truck is in gear, even if the headlights are off.