Are all 302 distributors the same?
Are all 302 distributors the same?
Registered. The distributor in the 351w is the same length as the 302 distributor, but the 351w does use a larger diameter oil pump drive shaft. The larger drive shaft will require the larger diameter distributor shaft. The shaft diameter of the 302 distributor is .
Will a 351w distributor fit a 460?
No way will the 351W distributor fit into the 460. For one its longer than the 460 distributor and two the oil pump shaft hole is much smaller on the windsor. So you can change gears all you want, they will not physically interchange.
How much HP is a Ford 460?
General Information. The Ford 460-cubic-inch, V8 engine has a cylinder bore of 4.36 inches and a crankshaft stroke of 3.85 inches. The output for 460 engines built before 1972 is 365 horsepower at 4,600 rpm and 485 pound-feet of torque at 2,800 rpm.
Will a 302 distributor fit a 351?
Registered. Windsor distributors can be interchanged between all engines from 221 cid to 5.0L. However, because of the taller deck height, a 351W distributor is longer, and will not fit a 302 block, nor will a 302 distributor fit a 351W.
Will a 302 timing cover fit a 351W?
Yes the covers will interchange from 1 block to the other, but you have to match the timing cover to the water pump your using, either standard rotation or reverse rotation.
Will a 302 distributor fit a 351 Cleveland?
What kind of distributor does a 351 W use?
The 351 w uses the 289-302 style gear. This goes for stock points and Duraspark distributors as well as aftermarket stuff like MSD, Mallory, Accel etc. Also if you are going to use an Edelbrock Victor Jr on your 351 w with an MSD dist. for a 351 w, it will not clear the intake.
What’s the difference between a 289 and 302 V-8 engine?
289-2V V-8 (1968). Although the 302 has a longer 3.000- inch stroke, it has a shorter connecting rod (5.090 inches center-to-center), which is not interchangeable with the 221/260/289 rod (5.155 inches center-to-center). The 302’s shorter rod, when combined with the longer 3.000-inch-stroke 2M crankshaft]
What’s the difference between a 390 and a 427 Ford engine?
The 427, aside from the obvious cubic-inch advantage, has a stronger, better-lubricated block born of racing necessity. It was through Ford’s desire to win that the 427 was conceived at all. The 427 has the 390 and 406’s 3.78-inch stroke with a huge 4.23-inch bore.
What’s the difference between a Ford 360 and 406?
The 360 was used exclusively in pickup trucks while the 390 found use in both cars and trucks. The 406 came along in 1962 with the 390’s 3.78-inch stroke, but with a larger 4.13-inch bore, thicker cylinder walls, and heavier main-bearing webs.
Can you use a DUI distributor on a 460?
Visit our Distributor Gears page to select the correct gear for your camshaft. *Due to the large cap design, the DUI distributor may interfere with the thermostat housing on a 460. A compatible thermostat housing is available for $25.00, part number 84859 (see related products below).
The 351 w uses the 289-302 style gear. This goes for stock points and Duraspark distributors as well as aftermarket stuff like MSD, Mallory, Accel etc. Also if you are going to use an Edelbrock Victor Jr on your 351 w with an MSD dist. for a 351 w, it will not clear the intake.
Is there a DUI distributor for a Ford?
Don’t be fooled by the cheap imitation one wire distributors, the DUI is unsurpassed in quality and is the original one-piece ignition system for Fords! Please note that DUI Distributors are not ready for immediate shipping.
How tall is the intake manifold on a 302?
The 302 and 351W DUI will not clear a Victor Jr. intake manifold. We can extend the height 1/2″ – 1 3/4″ for an additional fee of $105.00. Extended distributors are custom order and cannot be ordered online.
