Easy lifehacks

Why does my 1999 Chevy Blazer not start?

Table of Contents

Why does my 1999 Chevy Blazer not start?

I have a,1999 blazer I put a new battery in. And now it the three or four times to start after I get it started in don’t have a problem starting it all day New fuel pump, pressure is good. New programed ecm, new delco spider. , still injectors are not emitting fuel. Starter fluid will fire the engine but won’t stay running.

What causes a Chevy Blazer to shut off while driving?

Sudendly looses power and shuts off while driving… Coolant or antifreeze Oil Fuel pump Fuel filter Battery Fuses For two week’s prior to incident when i shut off the truck i could hear a boiling like sound coming from the coolant resivoir.

Can a 93 K5 Blazer 5.7 start when cold?

My 93 k5 blazer 5.7 will start and run fine when the engine is cold. After it warms up it dies. Try to start it again and it sounds like it tries to start then the starter will bog and sometimes it turns over fine but just won’t start until it cools down.

Is the 2000 Chevy Blazer a good car?

Is the 2000 Chevrolet Blazer a good car? CARFAX used car owners give the 2000 Chevrolet Blazer 4.1 stars out of 5, with a total of 18 reviews. Reviewers especially like the 2000 Blazer for its families and performance. What is the MPG of the 2000 Chevrolet Blazer?

Where was the 2000 Chevy Blazer last serviced?

Last serviced in Sioux Falls, SD on 12/09/17 • Vehicle serviced <… No accident or damage reported to CARFAX. Purchased on 10/11/00 and owned in OH until 06/08/21. Driven an estimated 4,992 miles/year. No service history reported on this vehicle. Other damage reported. 1st owner purchased on 09/18/99 and owned in CA until 09/29/20 •

How is the Chevy Blazer rated by Carfax?

CARFAX used car owners give the 2000 Chevrolet Blazer 4.1 stars out of 5, with a total of 18 reviews. Reviewers especially like the 2000 Blazer for its families and performance. What is the MPG of the 2000 Chevrolet Blazer?

What to do if your Chevy Malibu won’t start?

Don’t over look the ignition switch.Engine cranks, no spark, no injection pulse, no fuel pressure and no theft light. Intermittent no start how do I check it.How to fix the theft passlock system in 2004 Chevy Malibu / Classic when the car won’t start. Loading…

What causes a Chevy Blazer to not start?

Believe It or Not neutral safety switch on the trans will cause them to not start even if everything else works . On my second Blazer it was the problem the both times Here ya go, let’s see if I can make anyone’s head spin on this one.. 2000 Chevy blazer zr2, stick key in , cranks and no start.

What causes a car to stall on a cold start?

It also manages the idle under changing engine loads, like when you kick on the air conditioning, turn on the headlights, or turn up the radio. When the idle air control valve malfunctions, you may experience a rough idle or the vehicle may stall entirely. This is especially true on cold starts.

What causes a car to start at the wrong time?

Spark plug wires are a source of electromagnetic interference (EMF), but this is usually only a problem on some aftermarket setups when this interference isn’t taken into account. A timing belt or chain that has skipped a tooth will throw off the cam timing, causing the intake and/or exhaust valves to open at the wrong time.

Why does my car not turn on when I start it?

When you try to start running the engine or press start, the vehicle won’t turn on. The engine simply turns but it does not work as it should. Check the ignition module, located in the distrbutor and check as well the sparking. I’ve already found the problem.

I have a,1999 blazer I put a new battery in. And now it the three or four times to start after I get it started in don’t have a problem starting it all day New fuel pump, pressure is good. New programed ecm, new delco spider. , still injectors are not emitting fuel. Starter fluid will fire the engine but won’t stay running.

My 93 k5 blazer 5.7 will start and run fine when the engine is cold. After it warms up it dies. Try to start it again and it sounds like it tries to start then the starter will bog and sometimes it turns over fine but just won’t start until it cools down.

Sudendly looses power and shuts off while driving… Coolant or antifreeze Oil Fuel pump Fuel filter Battery Fuses For two week’s prior to incident when i shut off the truck i could hear a boiling like sound coming from the coolant resivoir.

When you try to start running the engine or press start, the vehicle won’t turn on. The engine simply turns but it does not work as it should. Check the ignition module, located in the distrbutor and check as well the sparking. I’ve already found the problem.

What does it mean when your car says no start?

A No Crank Condition means that the engine is not turning over when you turn the key to crank the engine. The most common problem, that causes this condition is a failed starter motor. If your vehicle is suffering a No Crank Condition, this tutorial may be a good starting point: How To Test The Starter Motor (GM 4.3L, 5.0L, 5.7L).

Why does my GM 4.3L engine not start?

No Start Condition Basics There are three very basic components that the engine, in your GM vehicle, needs to start and they are: Air, Fuel and Spark. When your 4.3L, 5.0L or 5.7L GM vehicle cranks but does not start, it’s because one of these components is missing from the mix.

No Start Condition Basics There are three very basic components that the engine, in your GM vehicle, needs to start and they are: Air, Fuel and Spark. When your 4.3L, 5.0L or 5.7L GM vehicle cranks but does not start, it’s because one of these components is missing from the mix.

Why is my Chevy Vortec 4300 V6 leaking fuel?

In the L35 and LF6 engines, the spider injectors are known to leak at the pressure regulator and at the supply and return lines due to a design fault. Outside of leaking fuel onto the exterior of the engine itself, it can cause excess fuel to get sucked into the engine.

What to do if your car wont start after replacing the fuel pump?

Car won’t start even after I replaced the fuel pump. Car won’t start and turned off while driving. Replaced the fuel pump and I can hear it working. The car still won’t start.

What causes a car to not start with no gas?

Problem may be at wiring connector on top of fuel tank (hard to reach!). No gas in fuel tank (Check the fuel gauge, and keep in mind the gauge may not be reading accurately). Bad gas (Contaminated with water or too much alcohol or diesel fuel). If you just filled up with gas and now your car won’t start, suspect bad gas.

Why does my car not start when I start it?

There are three very basic components that the engine, in your GM vehicle, needs to start and they are: Air, Fuel and Spark. When your 4.3L, 5.0L or 5.7L GM vehicle cranks but does not start…it’s because one of these components is missing from the mix.

There are three very basic components that the engine, in your GM vehicle, needs to start and they are: Air, Fuel and Spark. When your 4.3L, 5.0L or 5.7L GM vehicle cranks but does not start…it’s because one of these components is missing from the mix.

What to do if your Chevy Blazer turns over?

If there is spark, then next would be to do a fuel bleed down test by hooking a fuel pressure gauge up to the Schrader Valve, turning the key to the on position letting it build up fuel pressure on the gauge, (should be 56 to 63 lbs) then turning the key to the off position and watch the fuel pressure gauge.

Why does my car not start when I turn the key?

This condition is usually due a failed fuel pump, a failed ignition coil, a failed ignition control module, a failed crank sensor, etc… that lets the engine crank (turn over) but does not let it start. A No Crank Condition means that the engine is not turning over when you turn the key to crank the engine.

What kind of engine does a Chevy Blazer have?

My2002 chevy 2 door blazer automatic transmission does the same thing,have replaced fuel pump fuel filter mounted in center of left frame middle area. New distributor and cap completely. Also a new battery. Full tune up. But havent done anything with sensors yet.

Why does my 1996 Blazer not start up?

Installed aftermarket stereo in my 1996 blazer. Now the speedometer tach dosent work and tranny dosent shift out of first VBulletinNew fuel pump started but then died won’t start back up 2000 4 door 4wheel drive Gear box Crankcase Oil leak Buzzing Jerking/Hesitation Stalls

My2002 chevy 2 door blazer automatic transmission does the same thing,have replaced fuel pump fuel filter mounted in center of left frame middle area. New distributor and cap completely. Also a new battery. Full tune up. But havent done anything with sensors yet.

Where can I buy a 2000 Chevy Blazer?

AutoNation Chrysler Dodge Jeep Ram North Richland Hills has a wide selection of exceptional pre-owned vehicles to choose from, including this 2000 Chevrolet Blazer.

Why is my Check Engine light on after installing fuel injection?

Most of the problems encountered while installing your fuel injection system or after a time of operation are very simple. If your check engine light is on you more than likely have a hard fault meaning something is grounded out, unplugged, operating out of range or has gone bad.

Why does my Chevy S-10 not start up?

Once the truck starts and is running you can remove the jumper to the fuel pump and it will continue to run. The only thing i can think of is that you are not getting the priming signal to the fuel pump, that the ECM if faulty. It turns over fine.

Are there any problems with the Chevy 4.3 Vortec engine?

The 4.3 Vortec engines made from 1996-2002 (L35 and LF6) have been reported to have engine knock problems. In a properly functioning engine, fuel burns in even pockets instead of all at once. The pockets burn in even timing, in sync with engine cycles. Engine knock occurs when the fuel burns unevenly and out of sync with the engine cycles.

Why is my Blazer 4.3L driving like a dog?

If you have Hesitation and surging on Blazer 4.3L and it’s driving like a dog—poor acceleration, hesitation, or a surge and you suspect a fuel problem, you may be partially right. But before you start replacing really expensive components like the fuel pump, try this: Disconnect the electrical connector to the MAF sensor and take it for a drive.

What causes hesitation and surging on Blazer 4.3L?

Fix Hesitation and surging on Blazer 4.3L If you have Hesitation and surging on Blazer 4.3L and it’s driving like a dog—poor acceleration, hesitation, or a surge and you suspect a fuel problem, you may be partially right.

Why does my car not start when I crank the engine?

If the engine doesn’t crank, or makes an unusual noise when cranking, you may have a starting system problem. The car’s security system may have made an error that disabled the fuel or ignition system, or the chip in the key may have failed.

Spark plug wires are a source of electromagnetic interference (EMF), but this is usually only a problem on some aftermarket setups when this interference isn’t taken into account. A timing belt or chain that has skipped a tooth will throw off the cam timing, causing the intake and/or exhaust valves to open at the wrong time.

What causes a car to have a no start condition?

Fuel pressure should not drop more than 5 lbs. in 3 minutes. If it does then the spider injection assembly is leaking, which will cause hard or a no start condition. 35 people found this helpful. No fuel from fuel pump to the carborator, I pour gas into the carborator and it runs. What may be causing that the fuel pump is new??

What causes a car to start but not keep running?

The engine requires the right amount of air and fuel to mix together for ignition. If there is a fuel leak somewhere, then the correct amount of fuel may not make it to the combustion chamber. This might be enough to allow the engine to start, but not keep running.

What causes a car to start and stall?

Check to make sure your spark plug wires or ignition coils are seated properly on each of the spark plugs. A detached or malfunctioning spark plug wire will cause misfires and often a stall as the engine struggles to stay running on fewer cylinders.

What are the problems with a 2001 Chevy Blazer?

Worst 2001 Chevrolet Blazer Problems #1: Faulty Transmission 2001 Blazer Average Cost to Fix: $3,000 #2: No Fuel To The Engine 2001 Blazer Average Cost to Fix: $700 #3: Coolant Leak 2001 Blazer Average Cost to Fix: $2,500

Are there any problems with the 1998 Chevy Blazer?

Check out our Chevrolet Blazer overview to see the most problematic years, worst problems and most recently reported complaints with the Blazer.

What kind of problems does a Chevy Blazer have?

I have a 1974 Blazer with a 305 in it, I just replaced spark plugs, cap, rotor, wires, fuel filter, some hoses and PCV valve. It starts up strong, runs fine for a bit – drive it around the neighborhood – then once I come to a stop it basically dies on me, sometimes it will start right back up again – sometimes it will just crank and crank.

Why is my Chevy Blazer stalling and stalling?

Check/clean EGR. This does have the newer style injection so could be fuel pump heats up and pressure drops – have to test at test port. Coil could be failing due to overheating due to ignition module never shutting off so always a low voltage to it.

What causes a truck to shut off and then start up again?

Answer: This could be a problem of a failing fuel pump. This is pretty common on this truck. Normally this would cause the truck to sort of stumble before it stalls. If it just instantly shuts off like you are turning the key off, then it may be a problem in the ignition switch in the steering column, or an ignition control module.

I have a 1974 Blazer with a 305 in it, I just replaced spark plugs, cap, rotor, wires, fuel filter, some hoses and PCV valve. It starts up strong, runs fine for a bit – drive it around the neighborhood – then once I come to a stop it basically dies on me, sometimes it will start right back up again – sometimes it will just crank and crank.

Check/clean EGR. This does have the newer style injection so could be fuel pump heats up and pressure drops – have to test at test port. Coil could be failing due to overheating due to ignition module never shutting off so always a low voltage to it.

Why does my car stall when turning in drive?

It is the fuel pump, which must have a minimum of 75 to 95 psi. The engine stalls when braking or turning the car. Your engine stalls because your IAC valve is not compensating the right rpm. Does it stall when braking or turning in Drive?

How does a Chevy Blazer start and stall?

One end is a snap or quick disconnect that you squeeze the 2 tabs and it pulls off (after pressure released). The other end requires 2 open end wrenches. The bracket it is in is held on by one 13mm bolt to the frame that has to be taken off to get the filter out of the bracket and the lines are simply snapped in to the top of that bracket.

How does the fuel system work on a Chevy Blazer?

Fuel system has a test port on the metal line that requires a special valve to connect and then ckeck the pressure. 60psi min with key on engine off (start pressure) and 54psi running. If those check out then on to electrical/sensors/etc. Any SES light on and codes?

Why does my truck not start after sitting for a long time?

This can happen when the check valve in the fuel pump assembly leaks pressure back into the fuel tank. The longer the truck sits the harder it is to start. Try this, turn the key on for 2 seconds then off, do this two more times then try and start it.

What happens if you run your gas tank all the way to empty?

If you make a habit of running your tank all the way to empty before filling up; your fuel pump will most likely die before its designed lifespan. Maybe you stopped to fill the gas tank and the engine will not restart. You have been shopping and when you returned to the car, the engine will crank over but will not restart.

What to do if your Chevy S10 won’t start?

EASY…Popping, Vapor locking…Jump time??… 1995-2008 – YouTube If playback doesn’t begin shortly, try restarting your device. Videos you watch may be added to the TV’s watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer.

What to do if your car won’t start after getting gas?

To avoid this, cancel and sign in to YouTube on your computer. An error occurred while retrieving sharing information. Please try again later. Good Vibrations? – Steering Wheel Shakes

What is the fuel system on a 1997 Chevy Blazer?

The fuel system in your 1997 Chevy S-10 Blazer consists of an in-tank fuel pump, fuel injectors and an on-board computer. By isolating each component and testing separately from the other parts, the cause of failures can easily be found.

One end is a snap or quick disconnect that you squeeze the 2 tabs and it pulls off (after pressure released). The other end requires 2 open end wrenches. The bracket it is in is held on by one 13mm bolt to the frame that has to be taken off to get the filter out of the bracket and the lines are simply snapped in to the top of that bracket.

How can I tell if my fuel pump relay is faulty?

2. Engine does not start. Another symptom of a faulty fuel pump relay is an engine that does not start. If the fuel pump relay fails the fuel pump will be left without power. The engine may still crank when the key is turned, however it will not be able to start due to lack of fuel.

Why does my fuel pump only run for a few seconds?

This sound is the electric fuel pump trying to prime the fuel system. It will only run for a few seconds and then shut off. If you are not sure you could hear it or if there is noise outside; you may have to try it several times. Turn the key on and wait then turn it off.

What to do if your Chevy 1500 won’t start?

The passlock sensor voltage reading has changed & you can relearn it to the PCM & you can start the truck again. To relearn, turn the ignition key to the on position for 3 10 minute cycles, turning the key to the off position for 5 seconds after each 10 minute learn.

Why does my Chevy 1500 turn over twice?

Okay, it’s not the ‘passlock sensor’. I reset it by leaving it in the on position for slightly over 10 minutes, turning it off for 5 seconds, and repeating 3 times. It still turns over, and dies. It did start the second time for about 1-2 seconds instead of just one turn; maybe two rotations. This has me thinking it is the fuel pump.

What causes a car to act like it has a bad starter?

Problems that might cause your car to act like it has a bad starter solenoid can include: Bad battery – If the battery voltage is low it will be unable to provide enough power to start your engine. Blown fuse – Sometimes the simplest explanation is the best one.

Why does my car not start when I push the start button?

False input or lack of input from sensors like the crankshaft position sensor (CKP) or camshaft position sensor (CPS) can prevent the engine from starting. Also, a bad throttle position sensor (TPS) may cut off the spark to the cylinders.

Can a blown fuse cause a starter to not start?

Blown fuse – Sometimes the simplest explanation is the best one. A blown fuse in the starter circuit could be the cause of a no-start problem. Broken or corroded wiring – Damaged or dirty wires to the battery or to the starter solenoid (or wires that are loose) can prevent sufficient power from reaching the starter.

Can a bad battery cause a car to not start?

Sometimes your car starts, sometimes it doesn’t. Intermittent operation can be a sign of a failing starter solenoid. Bad battery – If the battery voltage is low it will be unable to provide enough power to start your engine. Blown fuse – Sometimes the simplest explanation is the best one.

Why does my truck not start without starting fluid?

It turned out that i broke a small tab off of the distributor when i was replacing the cap…. that sucked, got a new distributor and was extra careful and it runs great now Well I Guess Ill Replace The Fuel Pump Beacuse I Have A Brand New Fuel Injector And Fuel Filter On It

Why does my 97 Chevy truck not start?

97 Chevy truck won’t start when it gets cold?? When ever it gets cold my truck will not start. Seems to be fuel pressure but can’t smell any gas like it was flooding. It does’nt even fire like it wants to start.

What kind of truck won’t start after sitting?

Repair manuals and support for cars and trucks manufactured by Chevrolet, a division of General Motors. 2003 S10 V6. If the truck is started everyday it starts right up with no problems. If left sitting for at least 24 hours it is hard to start it.

What to do if your S10 cranks won’t start?

(I know this is an old thread) Cranks but no start, added gas, still no start. Poured gas into intake, fired and ran until gas ran out. Bought fuel pressure tester, tested at 45 on rail but bled to zero in less than a minute. Bought fuel pump and pressure regulator to replace.

Once the truck starts and is running you can remove the jumper to the fuel pump and it will continue to run. The only thing i can think of is that you are not getting the priming signal to the fuel pump, that the ECM if faulty. It turns over fine.

(I know this is an old thread) Cranks but no start, added gas, still no start. Poured gas into intake, fired and ran until gas ran out. Bought fuel pressure tester, tested at 45 on rail but bled to zero in less than a minute. Bought fuel pump and pressure regulator to replace.

Can a bad fuel pump cause a car to not start?

Check fuel pump relay, ecm (computer) relay. It is not impossible that you got a bad fuel pump. If you can, have the fuel pressure tested. Even if there is fuel coming out, it must have the correct pressure. 17 people found this helpful. You should get something with starting fluid.

What to do when your car won’t start?

My car has an automatic transmission. The engine fuel injection on these engine have to have enough fuel pressure to pop the injectors open to get it to start. The system injectors are known to get clogged and stick when cold also. You would first need to check fuel pressure to make sure it is high enough, and replace the fuel pump if it is not.

Why does my car make a clicking noise when I try to start it?

If you hear a clicking noise (but nothing else) when trying to start your car, that means the starter solenoid or relay contacts are operating, but the starter isn’t cranking the engine. My Car Clicks But Won’t Start—What Does it Mean?

Why does my starter make a clicking sound when I turn the key?

Clicking sound coming from the starter. The relay is an all or nothing device, meaning that it either sends the full electrical current or sends nothing to the starter. However, there are some occasions when a damaged starter relay will cause the starter to make a clicking sound when you turn the key.

Pop the hood and disconnect the battery terminals. Locate the engine’s starter motor using your dusty manual or a quick Google search. Remove any parts necessary to access the starter motor. Disconnect any connections running to the starter motor. Remove the starter. Replace the old starter with the new unit.

If you hear a clicking noise (but nothing else) when trying to start your car, that means the starter solenoid or relay contacts are operating, but the starter isn’t cranking the engine. My Car Clicks But Won’t Start—What Does it Mean?

Why does my car starter not make a click?

The lights take a lot less amperage than the starter, so sometimes the lights come one but the starter won’t turn over the engine. Usually the starter makes a click (at a minimum) when this happens. – xpda Sep 22 ’11 at 19:05 Yes, mine was also started to work for 8 months just by measuring the voltage of the starter. Very strange.

Why does my car not start when I Turn on the lights?

This is the switch you turn in the key or it could be part of it that is connected to that mechanism in the steering wheel. To troubleshoot this, turn on all your lights, try to start the car. If the light dim considerably, your ignition switch is OK.

Why is a clicking sound coming from the starter relay?

Clicking sound coming from the starter One of the most important – and most forgotten – components of any vehicle’s ignition system is the starter relay. This electrical part is designed to redirect power from the battery to the starter solenoid, which then activates the starter to spin over the engine.

The 4.3 Vortec engines made from 1996-2002 (L35 and LF6) have been reported to have engine knock problems. In a properly functioning engine, fuel burns in even pockets instead of all at once. The pockets burn in even timing, in sync with engine cycles. Engine knock occurs when the fuel burns unevenly and out of sync with the engine cycles.

What to do if your Chevy Blazer won’t start?

Unplug wire from coil to disturber and crank engine see spark at coil what is wrong please help When you try to start running the engine or press start, the vehicle won’t turn on. The engine simply turns but it does not work as it should. Check the ignition module, located in the distrbutor and check as well the sparking.

Why does my 93 K5 Blazer not start?

My 93 k5 blazer 5.7 will start and run fine when the engine is cold. After it warms up it dies. Try to start it again and it sounds like it tries to start then the starter will bog and sometimes it turns over fine but just won’t start until it cools down. I found broken ground wire. Turn over but won’t start…

Can a bad crankshaft sensor cause a cylinder to misfire?

Should you feel or hear a brief stutter in the engine, it may be a sign of misfiring cylinders from a bad crankshaft position sensor. A failing crankshaft position sensor cannot provide the right information about piston positioning in the engine, causing a cylinder to misfire.

Can a car start with no fuel going to the carburetor?

Crank the engine and check for fuel at the carburetor. The engine may start with fuel from a remote source such as a fuel can. If the pump draws fuel from the can and not the tank the tank screen must be inspected and or replaced.

Can a car start without priming with gas?

Engine wont start until you prime the throttle body with fuel, then it starts and runs great! Clicking this will make more experts see the question and we will remind you when it gets answered.

Why does my car not start when I put gas in?

Ignition coils are coated with a varnish-like insulation that becomes brittle over time after being stretched then contracted repeatedly The insulation develops small fractures that open when heated and close… My car is not starting; what should I replace?

What should I do if my chevr wont start?

This may fix the hard start and if not, then the fuel injection spider would need replaced. If you want to have this inspected before moving forward with a repair, a certified pro from YourMechanic can come to your car’s location to diagnose the hard start and let you know what needs to be done.

Do you have to put gas in throttle body to start car?

My 97 s10 will run great but you have to put gas in the throttle body for it to start.It will turn over but needs the direct contact of gas. There is also this ticking noise that is only heard when you role the key over. My car has an automatic transmission.

What kind of engine won’t start unless you spray starter fluid?

Cars A-Z Engine will crank but won’t start unless you spray starter fluid in it Maintenance/Repairs dodge, ram1500 Ramprobs October 11, 2016, 7:27pm #1 Okay so I have a 2004 Dodge Ram Hemi, the truck was running fine all this weekend and was fine this morning.

Why does my Johnson Seahorse engine not start?

I have a 1964 Johnson Super Seahorse 40hp I’m trying to put back on the water. If I spray some starting fluid (WD-40 etc) into the cylinders and continue to spray directly into the Carb, it will run. But merely seconds after I stop spraying directly into the carb, the engine dies, meaning it’s burning the fluid, and not he fuel.

If there is spark, then next would be to do a fuel bleed down test by hooking a fuel pressure gauge up to the Schrader Valve, turning the key to the on position letting it build up fuel pressure on the gauge, (should be 56 to 63 lbs) then turning the key to the off position and watch the fuel pressure gauge.

What makes a 2001 Chevy Blazer not start?

Have a 2001 Chevy Blazer have replaced coil fuel pump crank sensor ignition module distribution and button just cranks no start 26 people found this helpful.

Fuel pressure should not drop more than 5 lbs. in 3 minutes. If it does then the spider injection assembly is leaking, which will cause hard or a no start condition. 35 people found this helpful. No fuel from fuel pump to the carborator, I pour gas into the carborator and it runs. What may be causing that the fuel pump is new??

How to troubleshoot a no start GM 4.3L pick up?

Testing a Cranks but Does Not Start condition on your GM 4.3L, 5.0L, 5.7L pick up, van or SUV is not that hard to do, if you have a solid diagnostic strategy. In this article I’ll show you the basics of testing such a problem.

What causes a Chevy Vortec distributor to not turn?

The cap is prone to warping from the heat, which results in the cap rubbing against the distributor rotor button. This causes the rotor bushing to wear out and the distributor begins to no longer be able to turn. The simplest option here to fix this problem is upgrading to a distributor that has an aluminum housing on it.

Why is my Chevy truck cranking but not starting?

Too slow is either a starter motor problem or a electrical supply issue. Too fast can indicate a broken timing chain for example. Not sure why you changed the starter motor unless it was turning the engine over too slowly. If it cranks normally, it’s not the starter motor… How did you verify spark?

What to look for when your engine won’t start?

Check for a blown fuse that may be preventing a circuit from working properly, like the fuel injection or computer system. To operate efficiently, an internal combustion gasoline engine needs a good spark, the right amount of fuel, and good compression (a healthy mechanical condition).

What makes an internal combustion engine not start?

To operate efficiently, an internal combustion gasoline engine needs a good spark, the right amount of fuel, and good compression (a healthy mechanical condition). The lack of any of these three things will prevent your engine from starting.

The engine pistons and valves (and all the other related components like: timing chains, etc.) are the ones responsible for the induction of the fresh air the engine needs for the combustion process. Although rare, internal engine mechanical problems can and do cause no-start conditions. Blown head gasket. Blown engine. 4.)

If you have Hesitation and surging on Blazer 4.3L and it’s driving like a dog—poor acceleration, hesitation, or a surge and you suspect a fuel problem, you may be partially right. But before you start replacing really expensive components like the fuel pump, try this: Disconnect the electrical connector to the MAF sensor and take it for a drive.

Fix Hesitation and surging on Blazer 4.3L If you have Hesitation and surging on Blazer 4.3L and it’s driving like a dog—poor acceleration, hesitation, or a surge and you suspect a fuel problem, you may be partially right.

1996 Chevy Blazer. 6 cylinder engine. While driving on the highway my Chevrolet Blazers engine just shut off. I pull over, wait a minute, then start the engine and continue down the highway again. A minute later the engine shuts off again. This happens 7 or 8 times.

What does it mean when your car says no crank?

A No Crank Condition means that the engine is not turning over when you turn the key to crank the engine. The most common problem, that causes this condition is a failed starter motor. The most common problem, that causes this condition is a failed starter motor.

This condition is usually due a failed fuel pump, a failed ignition coil, a failed ignition control module, a failed crank sensor, etc… that lets the engine crank (turn over) but does not let it start. A No Crank Condition means that the engine is not turning over when you turn the key to crank the engine.

Author Image
Ruth Doyle