Why do you need a water pump in a Dodge Stratus?

The water pump in your Dodge Stratus is used to help move coolant from the radiator to the engine. This heps prevent the engine from overheating. If your water pump stops working correctly, it can cause long term damage to both your engine and radiator. If your water pump becomes damaged in any way you should therefore replace it immediately.

How do you remove a water pump from a car?

Use a nut driver to loosen the bolt on the accessory drive belt tensioner. This will loosen the drive belt from around the engine. Remove the drive belt from the vehicle. Remove the mounting bolts on the rear timing belt cover to gain access to the water pump. Disconnect the heater hose from the water pump.

How do you fix a new water pump?

Attach a new gasket and o-ring on to the new water pump. Fix the water pump in place with the mounting bolts to a torque of 105 inch-pounds. Attach the heater hose to the water pump. Place the accessory drive belt on to the tensioner.

How do you remove battery from Dodge Stratus?

Open up the hood of your Dodge Stratus. Support the hood with the hood stand. Locate the battery. Use a wrench to remove the clamp bolt from the negative battery terminal. Lift the negative cable away from the terminal. Place the drain pan underneath the radiator. Remove the drain plug from the bottom of the radiator.

What to do if your water pump stops working?

If your water pump stops working correctly, it can cause long term damage to both your engine and radiator. If your water pump becomes damaged in any way you should therefore replace it immediately. Open up the hood of your Dodge Stratus.

Where is the water pump on a Chrysler 3.0 engine?

The pump or the pump gasket will leak. It can be hard to pinpoint the source, but if it is coming up from high on the engine, the pump is the likely source. This repair is difficult, owing to the location of the water pump on the front of the engine, under the timing belt cover.

Where is the water pump on a Chrysler 2.7?

Please try again later. The 2.7 engine has both the timing chain and the water pump on the inside of the engine. To access it, it is required to remove the timing chain cover, which also acts as an engine mount, mounting the engine to the frame of the car. With the mount removed, the engine must be supported by a jackstand placed under the oil pan.

How do you replace a dodge water pump?

Wrap the chain around the water pump, bring it up thru the head, and install your passenger side sprocket, lining the dot cut in the teeth to the last single plated link in the timing chain. Once you have your timing chain set up, next, install your left and right main timing chain guides.

How to replace a 2.7 water pump in a Dodge?

Remove the upper radiator support, and drain the coolant. Disconnect the battery, remove the air filter assembly, intake plenum, upper engine wiring harness, cooling fans, and upper radiator hose. Check and replace the lower radiator hose if needed. This is also a good time to inspect the trans cooler lines for leaks. One…. Two…. Three….

Why is my water pump leaking in my Dodge Intrepid?

This is not a job for the faint-of-heart, nor a job for those with no automotive knowledge. The car is a 2003 Intrepid with 73K miles. It began overheating randomly, and upon inspection I found water leaking from the water pump weep hole, just below the thermostat housing. It would only leak at certain times.

How big are the bolts on a dodge water pump?

Tighten the 6 water pump retaining bolts to 105 inch lbs. Now, it is time to install your inner (small) left and right timing chain guides. Tighten the bolts to 28 ft lbs.

Where is the weep hole on a Dodge Intrepid water pump?

The car is a 2003 Intrepid with 73K miles. It began overheating randomly, and upon inspection I found water leaking from the water pump weep hole, just below the thermostat housing. It would only leak at certain times. There are two weep holes on a 2.7, one is pictured, the other is below the lower intake manifold.

Can a water pump be replaced on a charger?

This 2008 Dodge Charger 2.7l was in need of a new water pump due to it leaking. Showing an overview of whats involved in the task. At a bare minimum the tensioner, pump and gaskets should be replaced during this job. It wouldn’t be a bad idea to replace the entire timing chain set as well if you have 100k+ miles on the clock.

Can you replace a power steering pump on a Dodge Stratus?

If you are installing a new or rebuilt power steering pump on your Dodge Stratus, you might need to transfer the pump pulley from the old unit onto the new one. You can replace it using a pulley puller, which you can rent at an auto parts store. Check at your local auto parts outlet before removing the pump.

Why is the oil pump on my Dodge Durango not working?

The oil pump is responsible for taking the oil from the oil pan and pumping it through your Durango’s engine. When it begins wearing out, its ability to pump oil will be diminished. There is a screen in most oil pumps that keeps large debris from entering.

How can you tell if your water pump is out?

The water pump impeller can wear out, thus no longer moving coolant around, so your car overheats. To test this. Do a cold start with Radiator cap off,; you should see the fluid moving around some in the radiator. If not, then there is a good chance the internal water pump blades are gone or only a small amount left.

What can cause a car water pump to need replacing?

A leak or a faulty bearing can cause serious damage to your car’s engine. Puddles of coolant underneath your vehicle or high temperature readings may be signs that your water pump needs replacing.

When does a car water pump warning light come on?

Notice if your temperature warning light comes on. If your car is not circulating enough coolant due to a leaky or malfunctioning water pump, your engine temperature is going to increase, triggering the warning light.

What causes water to leak out of a water pump?

Many water pumps have a weep hole in front of the seal that will allow water to leak out if the seal is bad.

How do you replace a lower thermostat on a Dodge Stratus?

The metal housing the hose connects to is the lower thermostat outlet. Remove the hose from the outlet by loosening the band clamp and then by pulling the hose off the outlet. Be careful–some fluid will drain from the hose.

Where is the radiator hose on a Dodge Stratus?

Find the location where the upper radiator hose connects to the intake manifold of the engine by tracing it from the radiator to thermostat intake housing bolted to the intake. Remove the radiator hose from the thermostat intake housing by loosening the band clamp that secures it into place.

Why do you need a water pump in a Dodge Stratus?