Where is the power fuse on a Chevy Cobalt?

Cigar lighter (power outlet) fuse in the Chevrolet Cobalt is located in the Engine Compartment fuse box (see fuse “OUTLET” or “LTR”). It is located on the passenger side of the vehicle, on the lower portion of the instrument panel near the floor, behind the cover. It is located in the engine compartment, under the cover. How to check the fuses?

When did the Chevy Cobalt first come out?

In this article, we consider the first-generation Chevrolet Cobalt, produced from 2004 to 2010. Here you will find fuse box diagrams of Chevrolet Cobalt 2005, 2006, 2007, 2008, 2009 and 2010, get information about the location of the fuse panels inside the car, and learn about the assignment of each fuse (fuse layout) and relay.

What happens when an ECM power relay goes dead?

If the relay shorts it can leave power on to the computer, even when the vehicle is turned off. This will place a parasitic drain on the battery, which will eventually cause it to go dead. The ECM power relay is one of the most important relays as it provides power for the vehicle’s computer system.

How many volts does a Chevy Cobalt have?

Not open for further replies. With ignition in crank position there is 12 volts going to starter signal wire as long as it is unplugged from starter but shows 0 volts if plugged into starter?

Why do I get no crank signal on my Chevy Cobalt?

If the fuel pump isn’t coming on you are not getting the crank signal from the BCM… Click to expand… Big fuse in trunk is good. Battery voltage may be low now but was good while checking, I will recharge and check to make sure it is up to par before proceeding with further tests (or install another battery).

Why do I get 12volts on my Chevy Cobalt?

The reason you get 12Volts is because there’s a pull-up sense resistor on the BCM module. Normal I believe. The reason you get 12Volts is because there’s a pull-up sense resistor on the BCM module. Normal I believe. Click to expand…

Why is the ignition switch on my boat not working?

I will assume that the Ignition switch has no power to it. (easily confirmed with a 12 v bulb tester) and the gauges do not move when the switch is turned on/off.. The typical arrangement is for the ignition switch power to come from the battery cable to the starter and than go to a circuit breaker on top of the engine .

What is the name of the fuse box?

Fuse box diagram № Name Description 1 FUSE PULLER – 2 EMPTY Not Used 3 EMPTY Not Used 4 EMPTY Not Used

What are the sensors on a Chevrolet Cobalt?

Evaporative Emission (EVAP) Canister Purge Solenoid, HO2S Sensors, Mass Air Flow (MAF)/Intake Air Temperature (IAT) Sensor type 2. Heated Oxygen Sensor (HO2S) Sensor 1, Heated Oxygen Sensor (HO2S) Sensor 2, Evaporative Emission (EVAP) Canister Purge Solenoid, Clutch Pedal Position (CPP) Switch, Mass Air Flow (MAF).Inlet Air Temperature (IAT) Sensor

Where is the fuse box on a cobalt?

Fuse box diagram: Chevrolet Cobalt (2005-2010) Cigar lighter / power outlet fuse in the Chevrolet Cobalt is located in the Engine Compartment fuse box (see fuse “OUTLET” or “LTR”). It is located on the passenger side of the vehicle, on the lower portion of the instrument panel near the floor, behind the cover.

Where are the fuse blocks in a car?

There are two fuse blocks in your vehicle: the floor console fuse block and the engine compartment fuse block. Before replacing a fuse check that the key has been removed from the ignition and that all the services are switched off and/or disengaged. Do not repair fuses and never replace a blown fuse with one that has a higher amp rating.

Why does the reduced power light come on on my Chevy Cobalt?

This is one of the most common reasons the reduced engine power light comes on. If the ECU isn’t getting the proper voltage response from the throttle body, it can’t be sure of how much it’ll really accelerate your Cobalt from the gas pedal input.

What does the oxygen sensor do on a Chevy Cobalt?

Your Cobalt’s oxygen sensors measure the amount of oxygen in the exhaust to help insure that the proper air/fuel mixture is realized.

What is the throttle position sensor on a Chevy Cobalt?

The throttle position sensor is one of the most vital sensors in your Cobalt. If it’s not responding, the ECU has no way of telling how much gas gas you’ve given it. The TPS data also helps determine when the transmission will shift.

Why does my Chevy Cobalt have a reduced engine power warning?

Here are some of the most typical problems that can make your Cobalt’s reduced engine power warning come on: This is one of the most common reasons the reduced engine power light comes on.

Your Cobalt’s oxygen sensors measure the amount of oxygen in the exhaust to help insure that the proper air/fuel mixture is realized.

What are the codes for reduced engine power?

GM has issued multiple services bulletins to address a Reduced Engine Power message with trouble codes on the vehicles listed below. The most common trouble codes that show up are P0106, P0651, and P2135, but the bulletin also lists these possible trouble codes These codes may trick you into replacing the MAP or Accelerator pedal position sensor.

Who is the owner of the Chevy Cobalt?

GENERAL MOTORS, GM, the GM Emblem, CHEVROLET, the CHEVROLET Emblem, and the name COBALTare registered trademarks of General Motors Corporation. This manual describes features that may or may not be on your specific vehicle either because they are options that you did not purchase or due to changes subsequent to the printing of this owner manual.

How to start a Chevy Cobalt owner manual M?

Starting the Vehicle 1. Aim the RKE transmitter at the vehicle. 2. PressQ. 3. Immediately after completing Step 2, press and hold/until the turn signal lamps flash. 1-4

How does the RKE transmitter work on a Chevy Cobalt?

The RKE transmitter is used to remotely lock and unlock the doors from up to 60 m (195 feet) away from the vehicle. PressKto unlock the driver door. Press again within five seconds to unlock all remaining doors. PressQto lock all doors. Lock and unlock feedback can be personalized. Press and holdVfor approximately one second to open the trunk.