Where is the ignition switch on a Chevy?

Set the cover and screws aside. Locate the black plastic J-shaped lever on the ignition switch, revealed after removing the plastic cover. Pull the lever toward the front of the vehicle to release the ignition switch. Carefully pull the switch down and remove it from the underside of the steering column.

How to remove the ignition switch without a key?

How to Remove the Ignition Switch Without a Key. 1 Step 1. Turn on your power drill and use your drill bit to make a hold in the key slot of the ignition cylinder. Be sure to make the hole large enough 2 Step 2. 3 Step 3.

What happens if you have an ignition switch problem?

However, if your car has ignition switch problems, you may not be able to start the car at all. Ignition switch problems can also cause issues on the road, such as unexpected shutdowns or electrical problems. To be sure, ignition switch problems are no fun, especially if they’re stopping you from getting to work or school or play.

How is the ignition switch connected to the trunk?

You might consider getting a matched lockset that includes the door and trunk cylinders. The ignition switch itself is connected to the ignition cylinder by a shaft or lever. Inside the ignition switch, several contacts connect vital electrical systems needed to start and run the car.

How do you remove an ignition switch from a 1987 Chevy?

Remove the two bolts holding the switch in place on the steering column with a socket wrench. Lift the ignition switch vertically away from the steering column, and discard it. Install a new ignition switch in your 1987 Chevrolet pickup by reversing the removal process entirely.

What happens when the ignition switch fails on a 1987 pickup?

When you turn the key forward in your 1987 Pickup, the ignition switch tags the starter relay, which then tags your starter motor. When the ignition switch fails, it will tag neither the relay nor the starter, resulting with your engine not starting.

What causes a Chevy pickup to not start?

by Marion Cobretti. A damaged or defective ignition switch in your Chevrolet pickup will prevent the engine from starting. The ignition switch essentially plays a game of three-way tag. When you turn the key forward in your 1987 Pickup, the ignition switch tags the starter relay, which then tags your starter motor.

Where is the pin on an ignition switch?

Remove the plastic tab holding the pin in place on the side of the new ignition switch, and discard it. Do not move the metal slider pin next to the plastic tab. If your new ignition switch for some reason does not come pinned down already, move the metal slider pin on the switch all the way to the left.

How to get an ignition cylinder out without the original key?

How to Get an Ignition Cylinder Out Without the Original Key Step 1. Disconnect the negative battery cable from your vehicle, which will eliminate the chance of getting shocked… Step 2. Use a screwdriver and socket wrench set to disassemble the steering column covering and lower dashboard …

When does an ignition module need to be replaced?

If the light blinks, the module is good. If the light is blank or constant, the module is bad. Before you attempt to replace the control module, you must rule out other ignition system components. The module is expensive and replacing it is a laborious process. Check the ignition coil for a spark.

How to know if you need an ignition switch replacement?

In order to find out if you need an ignition switch replacement, first, you need to look at how the car is behaving. The initial step in diagnosing this issue is to check to see what is happening when the key is rotated to different positions. With an ignition, there are commonly four distinct places the key can be turned to.

Is the ignition switch the same as the ignition cylinder?

Though the ignition switch is not the same as an ignition cylinder, they are both needed for the key to work correctly. On top of being a lock problem, a locksmith can come to your location. Mechanics rarely offer a mobile service that frees the customer up avoid using the vehicle that has been functioning improperly.

Where is the ignition switch on a Chevy Silverado?

The Silverado’s ignition switch is not what your key goes into. That is called the lock cylinder. The ignition switch typically sits directly behind the lock cylinder. It has three main functions.

How do you replace an ignition switch on a car?

Installing a Replacement Squeeze the release pin on the ignition switch so it’s flush with the side. The same release pin that stopped the switch from coming out now needs to be pressed in so you can slide the switch into place inside the ignition module. Slide the ignition switch into its hole.

What are the symptoms of a bad ignition switch?

These include stalling issues, not starting, and no power to the radio or accessories. The Silverado’s ignition switch is not what your key goes into. That is called the lock cylinder.

Can a bad ignition switch cause a Chevy Silverado to stall?

Your Silverado stalls because the faulty switch turns off the fuel pump or power to the ignition. When this happens, the engine will not be able to run until it gets that signal back. 2. Starts then Dies If your Chevy Silverado is starting right up, but then immediately dies, that is a very good indication that the ignition switch is bad.