Where is the ignition switch on a Chevy Monte Carlo?

The ignition switch typically sits directly behind the lock cylinder. It has three main functions. Power the Accessories- This should be what you get when you turn the key to the first position. This allows you to use the power windows, radio, and any other accessory that is equipped in your Chevy Monte Carlo.

What’s the name of the ignition lock cylinder?

The ignition lock cylinder is the cylindrical tumbler and key that is used to power on and start the vehicle. While many newer vehicles are now being manufactured with push button and keyless power and starting systems, traditional ignition lock cylinders are still commonly found on many road…

Why is my ignition lock cylinder not working?

The ignition lock cylinder is connected to an electronic ignition switch, they work power on and start the vehicle. If the ignition lock cylinder wear out or breaks, it may prevent the vehicle from starting when the key is inserted and turned. A no start condition can also be caused by a wide variety of other issues,…

Where is the electronic ignition switch located on a GM car?

A typical symptom of failure is the security light illuminating on the dash. Also, keep in mind the electronic ignition switch is located just behind the lock cylinder. It is the plastic part that the ignition lock cylinder fits into. It contains the actual electrical connections and wiring and it sends current to numerous different components.

What’s the best way to remove an ignition switch?

Remove them carefully by either popping them off of their plastic clips or removing the screws and bolts that hold those pieces in place. Refer to a vehicle specific repair manual for guidance on how best to gain access to the ignition switch. Set all trim pieces aside somewhere safe where they won’t get stepped on or damaged. Helpful?

What to do if your key is stuck in the ignition switch?

The key may be stuck in the ignition switch, but that shouldn’t stop you from turning it. If you don’t have a key, you will need to force the module to turn using a flathead screwdriver. Press the release pin inside the hole on the ignition module with a screwdriver.

How to replace a no start ignition switch?

GM Ignition switch replacement to fix a no start or intermittent start. Faulty ignition switch contacts can also cause the PassLock system to enable Click here to see step by step proceedures. http://www.thejunkmanadv.com/the-junk… Support the site, buy service manuals here : http://www.tkqlhce.com/click-7357719-… Loading…

How to replace GM PassLock ignition key lock cylinder?

Press the small release tab (see pictures) While turning key to the ON Position Installation is the reverse of the above procedures, see below for the relearn procedure Clear all Diagnostic Trouble Codes (DTC). Record and/or repair your DTCs before clearing. You can clear the codes by disconnecting the battery for 10 minutes.

Can a faulty ignition switch cause a car to stall?

A faulty ignition switch in your vehicle can cause several problems ranging from your car stalling and all lights going dark to the radio not working unless the key is wiggled from side to side. Once you’ve been able to identify the ignition switch as the source of your trouble,…

What’s the Accessory position on an ignition switch?

Insert the key and turn it to the “accessory” position. The ignition switch needs to be set to the accessory position before you can release it from the ignition module. The “accessory” position is before the starter is engaged, and would normally let you run the vehicle’s electronics without the engine running (when the battery is connected).

How do you take the ignition switch out of a car?

With the release pin pressed, pull the ignition switch straight out of its place beneath the steering wheel. It should come without any resistance, but it’s not unusual for it to stick a bit in older vehicles that have accumulated a lot of dust and debris around the cylinder.

Why does my car key turn freely in the ignition?

Went to start vehicle, key turned normally, acc power came on but car wouldn’t start. Turned key to off position and acc power stayed on. Key now turns freely in the ignition and the only way to turn off the power is to disconnect the battery.

Why is the ignition switch on my car not working?

My car has an automatic transmission. The ignition switch or linkage to the switch is broken. The ignition switch needs to have the small linkage from the back side of the key lock cylinder to turn the switch to start and run the vehicle.

What to do if your car key does not release?

1. The car will not shift out of park. 2. The key will not release from the ignition. Remove the center console to determine if one of your wires is broken or disconnected from the clip. If so, this fix should work well for you. 1. ACDelco Part Number PT3923 / GM Part Number 13583923 2. Phillips Screwdriver 3. Wire Strippers/Cutters 4. Crimper 5.

How to replace the ignition switch on a GM car?

1. Insert ignition key and turn to the “ON” position. Do not attempt to start the engine. Leave the key in the “ON” position for approximately 11 minutes. The security light will be steady on or flashing for the 11-minute period. Do not proceed to Step 2 until the security light turns off or stops flashing. 2.

How does TDM validate resistive chip in ignition key?

The TDM portion of the BCM will validate the resistive chip in the ignition key. If resistance value read by the BCM is what the BCM is expecting, the BCM will send a message over serial data to the PCM informing the PCM that a valid key is present and the PCM may start the vehicle.

Where is the ignition key lock cylinder located?

The ignition lock cylinder contains the pass-lock security chip that is extremely common to fail on the above vehicles. A typical symptom of failure is the security light illuminating on the dash. Also, keep in mind the electronic ignition switch is located just behind the lock cylinder.

What are the symptoms of a bad ignition switch?

The most noticeable symptom of a bad ignition switch is stalling. Your Monte Carlo stalls because the faulty switch turns off the fuel pump or power to the ignition. When this happens, the engine will not be able to run until it gets that signal back.

Do you have to take steering wheel out to replace ignition switch?

Take the steering wheel out if it’s in the way. In some vehicles, you may be able to replace the ignition switch without removing the steering wheel. However, if you’re unable to get access to the top of the ignition switch with all the interior trim pieces removed, the steering wheel may need to come out.

Where is the ignition switch on a Chevy Monte Carlo?