Easy lifehacks

When did my Ford Explorer start stalling out?

When did my Ford Explorer start stalling out?

My 2006 Explorer started stalling with no warning at around 18000 miles in Feb 2007. I have had discussions with Ford since and the car has been in to two dealerships in NC.They have no codes coming up and cannot replicate the problem.

Is there a problem with my Ford Explorer?

The last dealership had it for 10 days and someone drove it for over 300 miles with no diagnosis.I insisted that they keep the car until it stalled but they bailed out on me saying the rental car was costing them too much money! I will take your advice and insist the manager drives with his family the next time.

What causes a bad torque converter in a Ford Explorer?

In the Ford Explorer, a bad torque converter is often caused by bad transmission fluid, worn clutches, bad seals, or loose bolts. Symptoms of a bad torque converter include a vibration, too much RPM on the highway, and slipping. Bad Torque Converter Symptoms: Ford Explorer

How to tell if a starter relay is bad in a Ford?

Fortunately, all Ford models have a remote relay near the battery, which makes it easy and convenient for troubleshooting. This guide will help you determine whether the starter relay on your Ford has gone bad, using a jumper wire and a multimeter. Disable the ignition system.

My 2006 Explorer started stalling with no warning at around 18000 miles in Feb 2007. I have had discussions with Ford since and the car has been in to two dealerships in NC.They have no codes coming up and cannot replicate the problem.

When does Ford Explorer hesitate during acceleration inspection?

Ford Explorer Engine hesitates during acceleration Inspection at your home or office. Our certified mobile mechanics come to you 7 days a week between 7 AM and 9 PM. Our certified mobile mechanics can come to you now. Ford Explorer Engine hesitates during acceleration Inspection costs $89 on average.

What to do if your Ford Explorer won’t start?

You need to get the truck towed to the dealer if you don’t have a programed key. using a screwdriver will never ever start the vehicle. unless a programed key is present the fuel pump does not run. Makr.

What causes a car to stall after starting?

A vehicle with a failing mass airflow sensor may also stall soon after starting. Fuel Pump: The fuel pump in most modern vehicles sits inside the fuel tank and pumps fuel up to the engine. If a fuel pump cannot provide the correct pressure, fuel may have difficulty making it to the engine.

Where is the throttle position sensor on a Ford Explorer?

Your Ford Explorer uses a series of complex sensors to report what is going on to the ECU. The ECU then uses this information to adjust the timing, air fuel mixture, and more. When one of them goes wrong, it can lead to stalling for sure. Throttle Position Sensor – The throttle position sensor is typically located on the gas pedal.

Are there any problems with the Ford Explorer?

The 2002 Ford Explorer had the highest number of problems and complaints associated with any Ford Explorer model. The main issues deal with the faulty and damaged transmission, causing the Ford Explorer to undergo serious problems that need to be fixed in order for your car to continue running smoothly.

Why does my Ford Explorer have a vacuum leak?

On your Ford Explorer, you can have a rough idle and stalling, along with misfiring and losing power. The intake manifold O-ring gaskets can leak, creating a vacuum leak. The O-ring gaskets are designed to seal off two or more parts, creating a vacuum-proofed seal.

How does the cooling system work on a Ford Explorer?

Your Explorer’s cooling system works by cycling the engine coolant from the engine through the radiator. The water pump pushes the water through the entire system. The thermostat opens up once the engine reaches operating temperature and allows coolant in. If any part of this system fails, your Explorer will eventually overheat.

The last dealership had it for 10 days and someone drove it for over 300 miles with no diagnosis.I insisted that they keep the car until it stalled but they bailed out on me saying the rental car was costing them too much money! I will take your advice and insist the manager drives with his family the next time.

Your Ford Explorer uses a series of complex sensors to report what is going on to the ECU. The ECU then uses this information to adjust the timing, air fuel mixture, and more. When one of them goes wrong, it can lead to stalling for sure. Throttle Position Sensor – The throttle position sensor is typically located on the gas pedal.

Why does my Dodge Avenger stall when I push the gas?

VVT Problem – Many modern engines are equipped with Variable Valve Timing. This allows for the engine to be in the “sweet spot” of power or economy depending on how hard you are pushing the gas pedal. If there is a VVT issue, it’ll often throw trouble P0010, P0011, or other related trouble codes. This is often the cause of the stalling.

The 2002 Ford Explorer had the highest number of problems and complaints associated with any Ford Explorer model. The main issues deal with the faulty and damaged transmission, causing the Ford Explorer to undergo serious problems that need to be fixed in order for your car to continue running smoothly.

How can I tell if my Ford Explorer transmission is failing?

The transmission failure in your Ford can be noticed by the car jumping gears without warning, slipping in and out of gears while you’re driving, or preventing you from going into any gear. These are all signs that your transmission has failed, or is currently failing.

On your Ford Explorer, you can have a rough idle and stalling, along with misfiring and losing power. The intake manifold O-ring gaskets can leak, creating a vacuum leak. The O-ring gaskets are designed to seal off two or more parts, creating a vacuum-proofed seal.

Why does my Ford Explorer die in cold weather?

I had a similar problem in my explorer, hard to start in cold, wet, weather had rough idle then would die out. I did some searching online and found the the issue was caused by the Idle Air Control valve. It was easy enough to find, probably just ahead of the throttle body in you vehicle, (double check in your repair manual).

How to fix a rough idle on Ford Explorer?

How to Fix a Rough Idle on Ford Explorer! PCV Vacuum Leak $5.00 | Ranger | EVAP – YouTube If playback doesn’t begin shortly, try restarting your device. Videos you watch may be added to the TV’s watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer.

What causes a Ford Explorer to stall out?

If you don’t own/want to buy a scanner, most local parts stores will run a scan for you at no cost (they want to sell you the parts). Here are some of the issues that cause the Explorer to stall out. Remember, a vehicle needs air, fuel, and spark to run.

How to Fix a Rough Idle on Ford Explorer! PCV Vacuum Leak $5.00 | Ranger | EVAP – YouTube If playback doesn’t begin shortly, try restarting your device. Videos you watch may be added to the TV’s watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer.

Why does my Ford Explorer have a theft light?

My Explorer was doing the intermittent theft light thing just like the rest of you. When I went to put in the new part I found that one of the wires that goes into the plug that is under the dash was broken. This break is was without a doubt caused by the wire being moved every time that you tilt the steering wheel.

When was the last time my Ford Explorer failed to read the chip?

The last time my 2001 Explorer failed to read the chip I just bumped the steering wheel a couple times to send vibrations through the column. It worked. Probably same effect as mentioned above by Sandra. The Ford mechanic said the “reader” will eventually fail all together and will need replaced. 51 people found this helpful.

Why does my Ford Explorer engine shut off without warning?

There are several complaints noted online with other Ford Explorer owners who have attributed it to a “terrain management” fault. This is the same diagnosis my local mechanic came up with. This results in the engine control module to receive a throttle position in the wide open indication causing the vehicle to shut off.

What are the problems with a 2004 Ford Explorer?

See all problems of the 2004 Ford Explorer . The contact owns a 2016 Ford Explorer. While driving approximately 40 mph, the engine shut off. The contact turned off and restarted the vehicle, and the check engine indicator illuminated. The vehicle was taken to a local dealer where it was diagnosed that the throttle body needed to be replaced.

How to fix an automotive engine stalling while driving?

Easy step by step guide on how to repair an automotive engine that has stalled or intermittently stalls while driving, this information is presented in order of popularity and pertains to most vehicles. Begin with the vehicle on level ground engine off (cold) with the emergency brake set.

When was the last time it happened at speed?

The last time it happened at speed was crossing the Chesapeak Bridge in Virginai Beach which was very very scary.

What’s the problem with my Ford Explorer 1995?

Explorer 1995 – 1996, A by-pass kit should be fitted. The kit consists of a distribution element, reducer element and modified coolant hose. Problem: Overdrive (O/D) warning lamp flashes with or without diagnostic trouble codes (DTCs) P0741 and P1740, or both, in memory.

What causes a Ford Explorer to start from cold?

The most likely cause is a damaged primary timing chain tensioner. Before commencing investigations, the oil level should be checked, the oil pressure should be checked (1 bar at 2000 rpm) and the engine should be started from cold to check for rattling.

When did my Ford Ranger start stalling out?

My problem began about 2 years ago. The truck would only stall out when I first began driving, after about a mile, and only if I was going downhill and was coming to a stop. Then it would putter and choke and ultimately stall out completely.

You need to get the truck towed to the dealer if you don’t have a programed key. using a screwdriver will never ever start the vehicle. unless a programed key is present the fuel pump does not run. Makr.

Why does my car stall after a few miles?

When a bad module is responsible for an intermittent stalling problem, the engine will usually cold start just fine and run OK for short distances, but stalls after driving more than a few miles or when driving at highway speeds (especially during hot weather). It’s as if somebody suddenly turned off the ignition.

Is there check engine light for intermittent stalling?

Many times, there will be no check engine light and no fault codes to give you a clue as to what might be causing the engine to stall. So the trick to diagnosing an intermittent stalling problem is to catch the vehicle when it’s acting up — and that rarely happens when you have the vehicle in your shop.

What causes an engine to stall at idle?

If the ISC valve is gummed up with fuel varnish or dirt, it may stick, preventing the engine from maintaining the proper idle speed when the throttle closes. A faulty idle speed control circuit may also allow the engine to stall when idling if it fails to compensate for idle loads placed on the engine by the charging system or A/C compressor.

Why does my car stall at highway speeds?

The engine may start and idle fine, but run out of power or even stall at highway speeds. If the engine starts right back up after stalling, the likely cause is low fuel volume delivery because of a weak pump. If the engine is running normally one minute, but suddenly quits, loss of ignition may be the problem.

What should I do if my Ford Explorer stops running?

The fix to this can be very very expensive, however, a quick fix is to turn the overdrive off in order to operate the cruise control and the truck will not shut off. I will post updates once my truck is evaluated by my mechanic for the wire that connects to the battery that maybe rubbed to the core.

Why does my Ford Explorer stall at red lights?

18 people found this helpful. just tried the fuel relay. instead of spending approximately $20 in a new one, I switched the A/c relay with the Fuel relay to test it. so far, my truck is not stalling when I stop at a red light. since my truck is only shutting off on me once a week, I am going to keep it like this for about three weeks.

I continually have various and numerous problems with fuel system. Is this typical for 2000 ford explorer sport 4×4. Have been pumping too much money into repairs and was hoping to get 300,00 miles on it!! I really do not want to buy a new one.

What kind of idle does a Ford Explorer have?

The Ford Explorer is known for a rough idle, engine stalling, loss of power, and misfires, accompanied by the check engine light.

What causes vacuum leak in Ford Explorer engine?

The intake manifold O-ring gaskets commonly leak, which creates a large vacuum leak. This vacuum leak causes unmetered air to enter the engine, and the fuel system becomes insufficient to compensate for the large amount of air reaching the engine. Replacing the intake manifold gaskets corrects this concern.

Why does my Ford Explorer make a rattle when I start the car?

Some 2004 F-150 and 2005 F-150, Expedition, Navigator, F-Super Duty and Mustang vehicles may have a rattle on startup that lasts 1 to 3 seconds. If initial pre-checks have been completed and the noise sounds like it is coming from the front engine, replace the VCT Phaser Kit.

Ford Explorer owners have reported 38 problems related to vehicle shudder (under the power train category). The most recently reported issues are listed below. Also please check out the statistics and reliability analysis of Ford Explorer based on all problems reported for the Explorer.

Why does my Ford Explorer shudder in Park?

Ford calls this their “limp home mode. ” the wrench icon warning would display and the entire vehicle would shudder until it was put in park and turned off. Usually, it would resume normal operations after being restarted, however, on one occasion, it took three attempts to restart.

Some 2004 F-150 and 2005 F-150, Expedition, Navigator, F-Super Duty and Mustang vehicles may have a rattle on startup that lasts 1 to 3 seconds. If initial pre-checks have been completed and the noise sounds like it is coming from the front engine, replace the VCT Phaser Kit.

Where can I get a new Ford Explorer?

The vehicle was taken to the local dealer orange park Ford located at 7700 blanding blvd, jacksonville, FL 32244 but the failures could not be duplicated and the cause of the failures were not determined. The manufacturer was not notified of the failures.

Why does my Ford Explorer leak in cold weather?

Radiator (1995, 1996): The radiator may leak in cold weather because of a bad seal between the tank and core. Suspension problems (1995, 1996, 1997, 1998, 1999, 2000, 2001): The sway bar links may bend or break because the original bushings are too rigid.

Why did my 1997 Ford Explorer catch fire?

1997, 1998 (with 4.0-liter engine): A gap between the plate and bore of the throttle body was too narrow, causing the throttle pedal to stick. 1997, 1998 (with SOHC 4.0-liter engine): Fuel lines can be damaged and a fire could result if the vehicle is jump-started and a ground cable is attached to the fuel-line bracket near the battery.

Why does my Audi A4 stall when I start the car?

Oxygen Sensor – The oxygen sensors measure the exhaust gasses after they exit the combustion chamber. The ECU uses this data to make adjustments to the air/fuel mixture. If one of them has gone bad, then it could lead to stalling.

Why does my Ford 99’4.0 run rough?

My 99′ 4.0 had a cold start problem also, it was the o-rngs in the upper intake. It would start and idle rough for several seconds untile the o-rings expanded just enogh to stop the air leak, after that the truck ran perfect.

What causes the Check Engine light to come on?

It kinda sounds like either a fuel problem or a sensor problem….Any ideas???? 1997 Ranger, 4.0L, 5 speed, 148k :whoaa: If it smooths out at higher RPMs you might try an Idle Air Control Valve, but this usually causes the Check Engine light to come on. If rough through all RPMs, could be a vacuum leak.

Why does my Ford Explorer stall at idle?

Problem Description. The Ford Explorer is known for a rough idle, engine stalling, loss of power, and misfires, accompanied by the check engine light. The intake manifold O-ring gaskets commonly leak, which creates a large vacuum leak.

Is it possible to find a misfire in a Ford?

It’s possible to find a misfire in your Ford, even if there is no check engine light. All you need is an OBDII scanner with Mode 6 function. It is a common situation. You’re driving your F150, F250, E150 van, or Expedition, etc and you can feel the engine skipping here and there.

What kind of car is the Ford Explorer?

We cover the Explorer, ST, Lincoln Aviator, Sport Trac, Mercury Mountaineer, Mazda Navajo, Ford Ranger, Mazda Pickups, and the Aerostar. On and offroad projects.

What kind of Lights do you put on Ford Explorer?

Place new posts in our new model year appropriate forum Aftermarket lighting. Driving lights, fog lights, rock lights, HID, halogen. Make your Ford Explorer light up the night!! Ford Explorer and Ranger, Engine, troubleshooting, modifications, performance and accessories. Transmissions, Transfer Cases.

Is the 1993 Ford Explorer a good car?

Used 1993 Ford Explorer Consumer Reviews “Great SUV Overall Since Buying it New in 1991” “311000 miles and still runs like new” “Terrific car. I have owned 3 of them, still have 2”

If the ISC valve is gummed up with fuel varnish or dirt, it may stick, preventing the engine from maintaining the proper idle speed when the throttle closes. A faulty idle speed control circuit may also allow the engine to stall when idling if it fails to compensate for idle loads placed on the engine by the charging system or A/C compressor.

What causes a Cadillac Escalade to stall at a stoplight?

If you let off of the gas coming to a stoplight and it stalls for a second or two and recovers itself, it very well could be a dirty throttle body that is causing the problem. Here’s a great YouTube video from EricTheCarGuy. on how to clean a throttle body.

What causes a Ford Ranger to stall at idle?

Well two items come to mind. A defective fuel pump or sticking Idle Air Control valve. The only good way to verify a defective fuel pump is to drive it with a fuel pressure gauge installed and monitor fuel pressure. I have replaced defective Idle Air Control valves, but normally that is more of a stall at idle issue.

VVT Problem – Many modern engines are equipped with Variable Valve Timing. This allows for the engine to be in the “sweet spot” of power or economy depending on how hard you are pushing the gas pedal. If there is a VVT issue, it’ll often throw trouble P0010, P0011, or other related trouble codes. This is often the cause of the stalling.

Why does my truck stall when I make a left turn?

Messages: 97. If it’s stalling due to the additional load applied by power steering at idle (foot off accelerator) then the engines idle control system could be at fault. Also with the heater changing this could be a vacuum problem.

Are there any problems with the 2004 Ford Explorer?

CarComplaints.com Notes: The 2004 Ford Explorer one of our worst vehicles on record. “Avoid like the plague” is putting it lightly. Read more » The 2002-2005 Explorer has a very well-established record of expensive transmission failure at under 100k miles.

Which is the worst model of Ford Explorer?

However, the 2006 Explorer is the worst-rated model due to the high repair cost and extra problems at lower mileage. The Ford Explorer has numerous problems in different categories that are a part of your vehicle.

When did Ford Explorer engine stall while driving?

December 1 2004 was driving 70 miles an hour and pressed cruise control when truck stalled, I almost got killed. I did not pay to much attention, I thought I did something my self. As time went on I realized was cruise control, since than happen so many time I was told that it was too expensive to fix and let it go, but is getting worse.

CarComplaints.com Notes: The 2004 Ford Explorer one of our worst vehicles on record. “Avoid like the plague” is putting it lightly. Read more » The 2002-2005 Explorer has a very well-established record of expensive transmission failure at under 100k miles.

Where is the gas cap on a Ford Explorer?

The gas cap was located behind the license plate and on every single Grenada, the spring on the license plate broke so they all drove around with their license plate facing the ground, wide open. We have no idea why the Check Engine light stays on. No idea why the back passenger windows quit working years ago.

Is there a MAP sensor in the Ford Explorer?

I am tired of spending on trying to figure out the problem Yes there is a map sensor in the ford explorer 2006-2010 4.0L it is located on top of the EGR VALVE and supplied with the EGR as a part. If you changed the egr and the code still there, you have to investigate further.

What do you need to know about fuses in Ford Explorer?

Electrical components such as your map light, radio, heated seats, high beams, power windows all have fuses and if they suddenly stop working, chances are you have a fuse that has blown out. If your Explorer is experiencing electrical problems, you should always check the fuses first, because they are relatively easy to check and cheap to change.

Where can I buy a 2006 Ford Explorer?

See pricing for the Used 2006 Ford Explorer XLT Sport Utility 4D. Get KBB Fair Purchase Price, MSRP, and dealer invoice price for the 2006 Ford Explorer XLT Sport Utility 4D. View local inventory and get a quote from a dealer in your area. Home Car Values Price New/Used My Car’s Value Instant Cash Offer Cars for Sale Cars for Sale Sell Your Car

What was the major change to the Ford Explorer?

The major change was making the worthy Advance Trac antiskid/traction-control system standard for all models. As before, it was integrated with Ford’s Roll Stability Control airbag activation system. In one other notable change, Explorer’s all-wheel drive was withdrawn, apparently for lack of sales interest.

Are there any issues with the Ford Explorer?

No problem climbing the mountain with it. Very dependable, 226,000 miles and still going strong! It’s my everyday driver too. Body with no corrosion issues, minor issues with plastic chrome pieces. Aluminum wheels with some oxidation. Other than replacing 2 coil packs engine and transmission have been flawless since purchase.

Is the Ford Explorer a two door or four door?

Meanwhile, the Explorer’s two-door Sport wagon and Sport Trac crew-cab pickup were unchanged for 2002. Both retained the basic 1995-2001 Explorer design and would see little change over the next few years. The new four-door Explorers earned Consumer Guide’s “Recommended” ribbon but not a Best Buy medal.

What does the theft light flashing on a Ford Explorer do?

The THEFT light flashing is a passive system that shuts off the fuel pump (cranks but won’t start or starts and dies). Does your key have a chip in it? You might try another (chipped) key if it does. You may need to hook up scan tool to see what is going on with the theft deterrent system.

18 people found this helpful. just tried the fuel relay. instead of spending approximately $20 in a new one, I switched the A/c relay with the Fuel relay to test it. so far, my truck is not stalling when I stop at a red light. since my truck is only shutting off on me once a week, I am going to keep it like this for about three weeks.

The THEFT light flashing is a passive system that shuts off the fuel pump (cranks but won’t start or starts and dies). Does your key have a chip in it? You might try another (chipped) key if it does. You may need to hook up scan tool to see what is going on with the theft deterrent system.

Why does my car die after 20 minutes?

After driving for about 20 minutes, the engine will die while driving, and will not start back up until the next day. I have sat in the car for literally 4 hours patiently waiting for it to start. I’ll turn the key and the engine will rotate, but will not start. When someone shows up to give me a jump after the battery gets low, it will not start.

What to do about hesitation on Ford 4.9L I-6?

A common issue on Ford’s 4.9l (300 c.i.d.) I-6 is hesitation and startup trouble. Simply remove the connector to the throttle position sensor and the idle speed controller and clean the terminals. 9 times out of 10 this will solve the issue.

Ford Explorer Engine hesitates during acceleration Inspection at your home or office. Our certified mobile mechanics come to you 7 days a week between 7 AM and 9 PM. Our certified mobile mechanics can come to you now. Ford Explorer Engine hesitates during acceleration Inspection costs $89 on average.

A vehicle with a failing mass airflow sensor may also stall soon after starting. Fuel Pump: The fuel pump in most modern vehicles sits inside the fuel tank and pumps fuel up to the engine. If a fuel pump cannot provide the correct pressure, fuel may have difficulty making it to the engine.

Oxygen Sensor – The oxygen sensors measure the exhaust gasses after they exit the combustion chamber. The ECU uses this data to make adjustments to the air/fuel mixture. If one of them has gone bad, then it could lead to stalling.

What do the Red wires on a Ford Explorer mean?

If you start at the battery + terminal it has 2 red wires coming out of it. They are both usually red and about the same thickness. One of them goes into a long black rectangle clip that says “fusable Link” or something like that.

Can a poor fuel pressure regulator cause a Ford to stall?

A poor fuel pressure regulator can also cause your Ford to stall while idling or driving. While it will most likely occur while idling, it is not unheard of for the car to stall while you are driving down the road.

Is the V6 Ford Explorer easier to work on?

The V8 would be easier to work on. The V6, although a great engine with more than enough torque, has a cam chain and chain driven oil pump on the back side of the engine that require the engine to be pulled to service them. I mention this because I also found a piece of chain tensioner in yesterdays oil change.

What kind of engine does a Ford Explorer have?

2007 Ford Explorer Specifications V-6 V-8 ENGINE Type Cast iron block and aluminum head Cast iron block and aluminum heads Manufacturing Location Cologne , Germany Romeo, Michigan Configuration V-6 V-8

What did Ford Explorer look like in 2006?

Completely redesigned in 2006, the 2007 Explorer’s interior now sports more angular styling along with several new features. One of the more tangible changes is the move of the shifter from the steering column to the floor.

What’s the difference between a 2007 Ford Explorer?

The 2007 Explorer remains a very obvious descendant of the first Explorer that materialized some 16 years ago and revolutionized the industry. The biggest and most obvious change is up front, with three grilles – each assigned to a particular trim level – inspired by Ford’s F-150 pickup.

When is a bad throttle position sensor a warning sign?

Engine won’t idle smoothly, idles too slowly, or stalls If you start to experience engine misfires, stalling, or rough idling when the car is stopped, it can also be a warning sign of a failing TPS. You don’t want to wait to get this checked out!

Can a bad crankshaft sensor cause the engine to stall?

If the crankshaft position sensor or its wiring have any issues, it can cause the crankshaft signal to be cut off while the engine is running, which can cause the engine to stall. This is usually a symptom of a wiring problem, however a bad crankshaft position sensor can also produce this symptom.

When a bad module is responsible for an intermittent stalling problem, the engine will usually cold start just fine and run OK for short distances, but stalls after driving more than a few miles or when driving at highway speeds (especially during hot weather). It’s as if somebody suddenly turned off the ignition.

Many times, there will be no check engine light and no fault codes to give you a clue as to what might be causing the engine to stall. So the trick to diagnosing an intermittent stalling problem is to catch the vehicle when it’s acting up — and that rarely happens when you have the vehicle in your shop.

Why does my Ford Explorer have a rough idle?

While there are a variety of reasons your Ford Explorer has a rough idle, the most common 3 are a vacuum leak, an issue with the spark plugs, or a problem with the ignition coil. See what others are asking about their Ford Explorer. Get answers from RepairPal’s community of auto experts and enthusiasts.

A poor fuel pressure regulator can also cause your Ford to stall while idling or driving. While it will most likely occur while idling, it is not unheard of for the car to stall while you are driving down the road.

While there are a variety of reasons your Ford Explorer has a rough idle, the most common 3 are a vacuum leak, an issue with the spark plugs, or a problem with the ignition coil. See what others are asking about their Ford Explorer. Get answers from RepairPal’s community of auto experts and enthusiasts.

Ford Explorer owners have reported 46 problems related to engine shut off without warning (under the engine and engine cooling category). The most recently reported issues are listed below. Also please check out the statistics and reliability analysis of Ford Explorer based on all problems reported for the Explorer.

Can a Ford Explorer shut off at any time?

Also please check out the statistics and reliability analysis of Ford Explorer based on all problems reported for the Explorer. The vehicle will just shut off at anytime. It’s not the auto start feature, all power will turn off at anytime. It has happened numerous times while driving waiting at a red light or to make a turn.

Why is my Ford Ranger stalling and stalling?

The intake manifold O-ring gaskets commonly leak, which creates a large vacuum leak. This vacuum leak causes unmetered air to enter the engine, and the fuel system becomes insufficient to compensate for the large amount of air reaching the engine.

What causes a car to start and stall?

Check to make sure your spark plug wires or ignition coils are seated properly on each of the spark plugs. A detached or malfunctioning spark plug wire will cause misfires and often a stall as the engine struggles to stay running on fewer cylinders.

What to do if your engine starts but does not keep running?

Engine Starts But Will Not Keep Running. Adjust Idle Speed. Disengage driven Units and check for loading from malfunctioning accessories. Make sure shutdown is not occurring too soon. Bleed the fuel system and check for suction leaks. Drain fuel-water separator or replace filter. Check for fuel waxing in cold weather.

Check to make sure your spark plug wires or ignition coils are seated properly on each of the spark plugs. A detached or malfunctioning spark plug wire will cause misfires and often a stall as the engine struggles to stay running on fewer cylinders.

Why does my Ford Explorer engine cut out while driving?

Others had commented that the engine at low speed cruise would kick into overdrive at low speed and just wind up going too slow to keep running. With the overdrive off I monitored the tach and saw that it would come down to around 800 rpm or lower when going downhill so it makes some sense that with overdrive on it might kill the engine.

How much does it cost to replace a Ford Explorer transmission?

The 2002-2005 Explorer has a very well-established record of expensive transmission failure at under 100k miles. The Explorer has an enclosed transmission which is typically replaced with a rebuilt transmission at a cost of almost $3,000.

Why does my Ford Explorer shudder when driving?

Loss of power: while driving my 2015 Ford Explorer XLT with 3. 5l v-6 engine on the highway (10/04/18), the wrench light came on and the car started to shudder and lose speed. Pushing down on the accelerator had no affect and the car rapidly decelerated. The engine was running very rough with heavy vibration.

Why does my Ford Explorer shake while braking?

The intermediate shift bracket sheared off/broke at the transition where it mounts to engine. Vehicle shakes violently while braking at higher speeds. . . Lesser movement at slower speeds while braking. I had just replaced my brakes and done them several time with rotors trying to correct the problem, thinking it was something I had done.

What causes a 1993 Ford F150 to stall out?

Check for the following conditions: Poor connection at PCM or IAC motor. Inspect harness connectors for backed out terminals, improper mating, broken locks, improperly formed or damaged terminals, and poor terminal to wire connection. Refer to Diagrams. Damaged harness. Inspect the wiring harness for damage. Restricted air intake system.

The last time it happened at speed was crossing the Chesapeak Bridge in Virginai Beach which was very very scary.

Why does my Ford Explorer crank but not start?

Spark. So, when your Ford 4.0L Explorer (Aerostar, Ranger or Mountaineer) Cranks but Does Not Start, it’s because one of these components is missing from the mix.

Why does my car stall at low rpm?

The will likely force your computer to stall the engine and only allow it to run at low RPMs, which means the car will only move at slow speeds. This is a safety feature enforced by the computer so that your engine doesn’t get too damaged.

What’s the burn time on a Ford Explorer?

If the Check Engine light is on and you’re doing misfire diagnostics on a 2006 and up Explorer, a new scan tool PID that’s available on these ­models is the actual burn time of each individual spark plug.

How does 4 wheel drive work on a Ford Explorer?

If that doesn’t work, try starting the truck put the transmission gear selector in neuteral. Then put the 4×4 switch/button into 4 low for a few seconds. Now put the 4×4 switch into 4 hi and then 2wd. Now put the transmission gear selector into drive or reverse move the truck 20-30 feet and it should be ok.

How do you unlock 4WD in Ford Explorer?

171 people found this helpful. If that doesn’t work, try starting the truck put the transmission gear selector in neuteral. Then put the 4×4 switch/button into 4 low for a few seconds. Now put the 4×4 switch into 4 hi and then 2wd. Now put the transmission gear selector into drive or reverse move the truck 20-30 feet and it should be ok.

What do the warning lights on a Ford car mean?

Not all warning lights indicate a massive, immediate problem with your car. Each Ford instrument cluster is loaded with warning lights and notifications, and not all are bad. Knowing what your dashboard is trying to tell you may prevent that panic attack the next time a warning light flips on.

What to do if your Ford dashboard light comes on?

Make an appointment with your local dealer as soon as possible. Charging System: If you’re driving while this light comes on, switch off all unnecessary electrical equipment that you may have running and get your vehicle checked by an authorized mechanic immediately.

What causes intermittent stalling on a Ford Escape?

Ford has also issued a recall (04S13) for 2001-2003 Ford Escape sport utility vehicles with 3.0L V6 engines for an intermittent stalling problem. The stalling typically occurs while decelerating at speeds below 40 miles per hour. The problem is caused by the calibration of the idle air control valve and evaporative emissions system.

What should I do if my car stalls and wont start?

If your vehicle stalls and won’t start again, but then starts without issue after sitting for a few minutes, it may be a clogged fuel filter. Fuel filters usually need to be replaced every 40,000 miles or so, but because the filter is the easiest and least expensive problem to address, it’s often a good place to start.

Why does my Ford Ranger stall all the time?

One of the most common issues your Ford Ranger is likely to develop is a stalling problem. The most challenging part of diagnosing a stalling problem is reproducing the conditions that led to the stall in the first place. Stalls can happen at any time, and it can be incredibly jarring when it does happen.

Why does my Ford F150 keep stalling?

One of the most common issues your Ford F150 is likely to develop is a stalling problem. The most challenging part of diagnosing a stalling problem is reproducing the conditions that led to the stall in the first place. Stalls can happen at any time, and it can be incredibly jarring when it does happen.

Why does my F-150 truck not start?

The next time the truck acts up depress the accelerator pedal and try to start it. If it starts up then there could be a problem with the Idle Air Control Valve, clogged IAC passages, or (less likely) an electronic problem with the IAC wiring.

When was the last time my truck stalled?

Three times now, once in April and twice this month it stalled while I was jockeying the trailer around the parking lot at church. The first time it had a full tank of gas and was at the beginning of the trip. I unhooked from the trailer and used another truck for the weekend.

Author Image
Ruth Doyle