What to use to clean throttle body of Dodge Ram?

When I did mine (2011 1500 5.7) In 2017, I just unhooked intake and connectors, unbolted the throttle body and used CRC throttle body cleaner from Canadian tire. I used a old tooth brush and be carful not to get any cleaner in around the electrical part of it. Throw everything back together.

How big is the throttle body on a Dodge Ram?

Yours is obviously tuned, so of course it should be a bit faster. The stock TB’s are more than large enough to feed a mildly modified engine, especially a 5.7. Stock 5.7 hemi TB bore is 80mm and has not changed since 2003, even with the introduction of the VVT engine in ’09. On top of that, both the 6.1 and 6.4 use (d) the same 80mm TB.

What’s the bore on a Dodge Ram 6.2?

Stock 5.7 hemi TB bore is 80mm and has not changed since 2003, even with the introduction of the VVT engine in ’09. On top of that, both the 6.1 and 6.4 use (d) the same 80mm TB. Only the wildly boosted 6.2’s got a factory upgrade to 92mm. Even more perspective, that monster 1000hp crate Hellephant 426? It uses the stock Hellcat/Demon TB.

What should I do if my Dodge Ram is making a vibration?

Answer: If this is a significant vibration, and both you and the dealer are certain the problem is originating from the driveline, it’s time to check the drive shaft angles. But first, here’s some stuff that you might want to try yourself.

How big of a shock does a Dodge Ram need?

Y you think they make dual shock it’s for 2500 and 3500 trucks. I have contacted tuff country, sky jacker, etc, and if lift in with bigger tire and wheels, foget it. The shocks can’t control the 110 pound tire, it just crashes into bumps etc.

How to read an error code on a Dodge Ram?

In order to read the error code, the following procedure must be performed: Turn the ignition off. After 5 seconds, turn on the ignition, immediately turn it off, turn it on again, turn it off and on again. (Remember that ignition does not mean starting the engine). What types of scanners does the dealer use to work with the Dodge Ram?

Where is the reset button on a Dodge Ram?

The reset procedure in your Dodge Ram is as easy as they come. First, park your truck and turn it off. Pull the hood lever under the driver’s side dash, and then pull the safety catch on the front of the hood to open it. Find the power distribution center (PDC); it will be a black box near the battery.

Why do I need to Reset my PCM on my Dodge Ram?

There are other reasons why you would need to reset the PCM, such as after the installation of aftermarket components that require a PCM reset so the truck can fully adjust to new components. The reset procedure in your Dodge Ram is as easy as they come.

How to reset the Check Engine light on a Dodge Ram?

Dodge Ram: How to Reset PCM and Check Engine Light. 1 Step 1 – Remove the PCM fuse. First, park your truck and turn it off. Pull the hood lever under the driver’s side dash, and then pull the safety catch 2 Step 2 – Reset the PCM. 3 Step 3 – Re-install the PCM fuse. 4 Related Discussions.

What causes bad throttle response on Dodge Ram?

An electrical glitch in the sensor can relay false readings to the computer and cause your air/fuel ratio to become inaccurate, which is accompanied with poor throttle response. This article applies to the Dodge Ram 3rd Generation (2002-2008). The throttle position sensor is mounted on the side of the engine throttle body.

Where is the throttle sensor on a Dodge Ram?

This article applies to the Dodge Ram 3rd Generation (2002-2008). The throttle position sensor is mounted on the side of the engine throttle body. It has a three-wire potentiometer, meaning it varies its resistance based upon its position.

When to install a new throttle body unit?

Ensure that your truck lives up to its promise by installing a new throttle body unit for Dodge Ram. When this part fails, you experience overall poor performance, including a loss of fuel economy and stalling problems. Get all the parts you need for your truck by shopping online with AutoZone.

How to replace throttle position sensor on Dodge Ram?

Option 2 – Cleaning or replacing 1 Remove the throttle position sensor from the throttle body. First, disconnect the electric connector from the sensor. 2 Drill a small hole into the sensor. Using a 1/8″ drill bit, make a small hole on the inner side of the sensor. 3 Clean the sensor. 4 Seal and re-install the sensor.

What to do if your throttle body is dirty?

Your computer may also turn on the Check Engine light and put the car into “limp home mode”. In some cases, dirt can build up on the throttle body, and cleaning it may resolve the issue. If you still have problems, it can also be replaced. At O’Reilly Auto Parts, we offer throttle body cleaners and parts to help you with your repair.

When did the first Ram 1500 come out?

Ram Truck 1500 is a full-size truck that’s been around since 1981. It’s been a light-duty offering under its own brand, however, since 2010, when Ram Truck separated from Dodge. The first generation took off in 2011 and ran until 2018. Cab options have ranged over the years from regular and quad to crew.

What kind of engine does a Ram 1500 have?

Engine choices have included gas, Cummins diesel, and EcoDiesel. Trims over the years have run from Tradesman to Express, SLT, LaRam Truckie, Sport, R/T, and LaRam Truckie Longhorn.

What should I use to clean my Dodge Ram?

You will need 04897156AA Mopar Throttle Body Cleaner, Scotch Brite Pad, (Green) or soft Bristle Brush. Remove the throttle body from the engine. Spray the entire throttle body bore and both sides of the throttle plate with Mopar Throttle Body Cleaner, p/n 04897156AA.

Are there any problems with the Dodge Ram 1500?

Fourth-generation Dodge Rams are more powerful than these trucks have ever been, yet they’re still susceptible to issues that can make them dangerous to drive. Electrical issues are unfortunately common in late-model RAMs and are some of the worst 2010 RAM 1500 problems. 1. TIPM Issues

What should I use to clean the throttle on a Dodge Ram?

If the throttle body plate and bore are coated with contaminates, perform the Cleaning procedure. You will need 04897156AA Mopar Throttle Body Cleaner, Scotch Brite Pad, (Green) or soft Bristle Brush. Remove the throttle body from the engine.

What to do when your Dodge Ram stalls?

Remove the throttle body from the engine. Spray the entire throttle body bore and both sides of the throttle plate with Mopar Throttle Body Cleaner, p/n 04897156AA. This will remove the bulk of the contaminant. CAUTION: This cleaner should only be used in a well ventilated area. Do not allow contact with skin or eyes.

What causes a throttle body to go bad?

A potentiometer sits on the throttle gear and returns signals to the computer through the sweeps on TB cover. Common failures are the swept area of the potentiometer getting wear marks in them, the sweeper arms breaking down, and the plastic teeth breaking or wearing off of the gears. Loading…

How does the electronically control throttle body work?

This is a video on how the electronically control throttle body works. Also, some of the common parts that fail and how they fail. A DC motor drives a toothed plastic gear, that in turn drives the throttle plate gear. A potentiometer sits on the throttle gear and returns signals to the computer through the sweeps on TB cover.

What are the common failures of electronic throttle?

Common failures are the swept area of the potentiometer getting wear marks in them, the sweeper arms breaking down, and the plastic teeth breaking or wearing off of the gears. Loading…

What to use to clean throttle body of Dodge Ram?