What should torque be on rear spindle nut?
What should torque be on rear spindle nut?
When tigntening the hub nut torque it to 55 – 65 lb ft then back off eight clicks (the nut will ratchet as you tighten and you need to back off eight clicks when you get it to torque spec). You also need to rotate the hub occasionally while tightening the nut to torque spec.
How much torque does a 2000 Ford F250 have?
Ford Super Duty Torque Specifications 2000 Ford F250 Torque Specifications These are torque values for a 2000 Ford truck. Most will be applicable to model years 1999-2003. Description Torque Specification Socket Size A/C compressor support bracket mounting bolts 30-41 lb/ft, 40-55 Nm A/C compressor support bracket mounting nuts
Where is the hub nut on a Ford truck?
The hub nut is either right (right side of truck) or left (left side of truck) hand thread depending on which side of the truck they are on. They are stamped RH and LH on the nut when you look at it as well. It also states a new hub nut must be installed if the old one separates during removal.
When tigntening the hub nut torque it to 55 – 65 lb ft then back off eight clicks (the nut will ratchet as you tighten and you need to back off eight clicks when you get it to torque spec). You also need to rotate the hub occasionally while tightening the nut to torque spec.
What happens when an axle nut is over torque?
Under torque of an axle nut will allow excessive movement causing uneven loading and excessive wear. Over torque of the axle nut will cause excessive load and cause the bearing to overheat, this is one of the most common causes
The hub nut is either right (right side of truck) or left (left side of truck) hand thread depending on which side of the truck they are on. They are stamped RH and LH on the nut when you look at it as well. It also states a new hub nut must be installed if the old one separates during removal.
Ford Super Duty Torque Specifications 2000 Ford F250 Torque Specifications These are torque values for a 2000 Ford truck. Most will be applicable to model years 1999-2003. Description Torque Specification Socket Size A/C compressor support bracket mounting bolts 30-41 lb/ft, 40-55 Nm A/C compressor support bracket mounting nuts
What are torque specs for rear rotor spindle on Ford Focus?
6,773 satisfied customers The torque specs on a 06 f350 super duty rear rotor spindle. The torque specs on a 06 f350 super duty rear rotor spindle nut …
How big is the torquing nut on a Ford Focus?
My experience with drums and rotors mounted on a spindle at the rolling end of any car is 17 lb/ft while rotating the drum or rotor, backing off the spindle nut one-half turn, then retorquing to approx. 10 lb/ft… Insert the cotter pin, install the dust cover and I’m done.
What are the torque specs for a Ford Taurus?
Ford torque specifications TORQUE SPECIFICATIONS FORD/MERCURY/LINCOLN APPLICATION FT-LBS / ( N-m) AXLE SPINDLE NUT PROBE 174-235 (235-319) ALL OTHERS 180-200 (244-271 BRAKE CALIPER BOLT (PROBE) 58-72 (79-98) CONTROL ARM-TO-KNUCKLE NUT SABLE & TAURUS 40-55 (54-75) ALL OTHERS 37-44 (50-60) CROSSMEMBER-TO-FRAME BOLT
What are the lug nut torque specs?
The correct torque for installing lug nuts on your 5 X 8 trailer’s 5-lug wheels will depend on the size of the lugs. For a 1/2-inch lug the torque spec ranges from 75- to 85-ft-lbs. For a 9/16-inch lug the torque spec ranges from 135- to 145-ft-lbs.
What are the torque specifications for lug nuts?
Typical Lug Nut Torque Specifications. Lug Size Ft/Lbs Torque. 1/2″ 90-120 9/16″ 120-140 5/8″ 140-160. IMPORTANT NOTICE: As with all types of wheels retorque lug nuts after the first 25 miles & at 100 mile intervals until lug torque is maintained. How to Measure Bolt Patterns.
What is the lug nut torque?
Lug nut torquing is expressed in foot-pounds. Use torque sticks with an air gun or a torque wrench to get the correct torque. If your studs or lug nuts are sized between 12 X 1.25mm to 1.5mm or are 7/16-inch, torque the nuts to 70 to 80 foot-lbs; 14 X 1.25mm to 1.5mm, to 85 or 90; 1/2=inch 75 to 85; and 9/16-inch 135 to 145.
What are torque specifications?
Torque specifications are for dry threads only. The fastener threads should be free of oil, dirt, grit, corrosion, etc. The hardware should turn freely without binding when tightened by hand. It is important NOT to lubricate hardware threads or seats. The friction at which torque is measured against should come from the hardware seats.
