What is the spec on a pinion nut?
What is the spec on a pinion nut?
If you are talking about the pinion nut it is not hand tighten. The spec measures the torque required to turn the pinion gear by itself once the nut is tightened. The spec is NOT the torque applied to tighten the nut. That is whatever it takes to achieve the pinon bearing pre-load which is determined as described above.
What are torque specifications for Chevy axle nut?
2012-2017 There are two types of wheel drive shaft nuts, both of which have different tightening torque specifications. Check the style nut that is on the vehicle when staking the nut. Style 1 nut has the thin collar (1.5 mm) thickness. Style 2 nut has the thick collar (2.7 mm) thickness.
What kind of torque does a Chevy Blazer have?
Search Car Torque Specifications by Engine or Model Torque Spec Database Click on One of the Links Below Model Torque Specifications Engine Torque Specifications for Chevrolet Blazer GM 4.3L-262ci-V6
How big is the torque cap on a pinion?
Pinion Preload (Reused) Ring Gear Backlash Ring Gear Bolt Torque Carrier Bearing Cap Bolts Chrysler 7.25″ 12 to 14 in-lbs. 6 to 7 in-lbs. .006″ to .010″ 55 ft-lbs.
If you are talking about the pinion nut it is not hand tighten. The spec measures the torque required to turn the pinion gear by itself once the nut is tightened. The spec is NOT the torque applied to tighten the nut. That is whatever it takes to achieve the pinon bearing pre-load which is determined as described above.
2012-2017 There are two types of wheel drive shaft nuts, both of which have different tightening torque specifications. Check the style nut that is on the vehicle when staking the nut. Style 1 nut has the thin collar (1.5 mm) thickness. Style 2 nut has the thick collar (2.7 mm) thickness.
Search Car Torque Specifications by Engine or Model Torque Spec Database Click on One of the Links Below Model Torque Specifications Engine Torque Specifications for Chevrolet Blazer GM 4.3L-262ci-V6
How big is the axle nut on a Cadillac?
Tang on ring must press through slot on spindle. Hole in pin must align with locknut. Turn adjusting nut to align. Endplay should be .001- .010″. With automatic locking hubs tighten adjusting nut to 50 ft-lbs/68 Nm while turning hub.
What’s the torque test on a Chevy yoke nut?
In other words, put the inch pound torque wrench on the pinion nut, with the carrier and ring gear OUT of the housing, and continuously spin the torque wrench and pinion, while reading the scale. If the drag is too low, tighten the pinion nut a small bit, and do the drag test again.
How much torque does a Chevy 4×4 have?
Im unable to take it to a shop right now not going to drive it in 4×4 on dry pavement with 35 inch tires. 74 Chevy 1/2 ton 4×4. Crate 350.Edelbrock intake,cam and carb. That is DRAG TORQUE.
What happens if you torque the yoke nut on a crate 350?
Crate 350.Edelbrock intake,cam and carb. You DON’T torque the yoke nut. The pinion has a crush sleeve in it that – if you over-torque it, will crush excessively and accelerate the gear wear (and it will whine a lot and possibly self destruct if bad enough).
What’s the lock thread on a torque nut?
IT IS SUPPOSED TO BE THAT WAY. The lock thread (whether plastic or a metal crimp style) keeps it from coming undone. Measure the depth of both of the yokes (where the shaft splines are cut into the yoke) to make sure they will fit in place of one another. You can use locktite if you want, but I wouldn’t use red – blue is good enough.
