What does FMI code 11 on a Caterpillar engine mean?

The FMI code 11 appears when the electronic unit registers more than one FMI code for one fault. FMI 12 – Faulty device or component. The FMI code 12 indicates the following status: the electronic control unit sends a signal to another electronic unit via a data link.

What is the SPN code for a FMI PID?

SPN FMI PID/SID PID/SID ID FLASH CODE FAULT DESCRIPTION 132 7 PID 132 1213 Intake Air Throttle Valve Closure Detection- Positive Torque 132 14 PID 132 1213 Intake Air Throttle Valve Closure Detection -Braking Condition 132 14 PID 322 1635 HC-Doser Fuel Pressure Not Plausible 132 1 PID 322 1213 Air Mass Flow Too Low

What is the engine coolant sensor code in FMI?

110 2 PID 110 1212 Engine Coolant Sensor (OUT), General Temp. Plausibility Error SPN FMI PID/SID PID/SID ID FLASH CODE FAULT DESCRIPTION 132 7 PID 132 1213 Intake Air Throttle Valve Closure Detection- Positive Torque 132 14 PID 132 1213 Intake Air Throttle Valve Closure Detection -Braking Condition

What is the fault code for a mid 128 engine?

Engine ECU Faults (MID 128) Fault Code Description FMI Codes MID 128 PID 26 Engine Fan Speed Percent 3,8 MID 128 PID 27 EGR Valve #1 Position Sensor 3,4,5 MID 128 PID 45 Preheater Relay Status 3,4,5 MID 128 PID 81 Particulate Filter 0,2,3,5,12

What are the Flash codes for a PID 7?

not present SPN F FMI P PID/SID P PID/SID ID F FLASH CODES F 70 2 2 P PID 7 70 2 2111 P 70 1 19 S SID 2 234 2 2112 J 70 1 13 S SID 2 234 2 2112 J 70 1 19 S SID 2 234 2 2112 J

What are the fault codes for a caterpillar?

Caterpillar Fault Codes PID/SID FMI Fault Description 1 11 injector solenoid cyl#1 current below normal or open 2 11 injector solenoid cyl#2 current below normal or open 3 11 injector solenoid cyl#3 current below normal or open 4 11 injector solenoid cyl#4 current below normal or open

What is the fault code for an ECU?

Engine ECU Faults (MID 128) Fault Code Description FMI Codes MID 128 PPID 326 Soot Level (DPF System) 0,11 MID 128 PPID 328 Aftertreatment Injection Shutoff Valve 3,4,5,7,14 MID 128 PPID 329 Aftertreatment Fuel Injector 3,4,5,7,14 MID 128 SID 254 Engine electronic control unit (EECU) 3, 8, 12

Where to find trouble codes for a 3406E?

Does anybody know of a place online to look up trouble codes for a 3406E? Every month 400 people find a job with the help of TruckersReport. Please Select… I Need CDL Training In CDL School Now CDL Grad, No Experience 1-5 Months 6-11 Months 1 Year 2 Years 3 Years 4 Years 5+ Years

What does the FMI code 12 mean on a truck?

The FMI code 12 indicates the following status: the electronic control unit sends a signal to another electronic unit via a data link. The electronic unit is waiting for a response, but either does not receive any response, or receives an incorrect response. The FMI code 12 can also indicate the following status:

What is the shop manual for a Caterpillar 3406?

Complete digital official shop manual contains service, maintenance, and troubleshooting information for the Caterpillar 3406, 3406B, 3406C, 3406E Engine. Diagnostic and repair procedures are covered in great detail to repair, maintain, rebuild, refurbish or restore your engine like a professional mechanic in local service/repair workshop.

Is the Caterpillar 3406E a bulletproof diesel engine?

The Caterpillar 3406E is a fairly bulletproof diesel engine in terms of problems. However, as with all engines, there are usually a few issues that are well known. You may have heard of oil leaks with the 3406E. A common spot for leaks is near the rear side of the engine around the spacer plate and the cylinder block.

How to repair a Caterpillar 3406E fuel manifold?

1. Put marks on the fuel lines connected to fuel manifold (1) for purposes of identification. Disconnect the fuel lines to fuel manifold (1). 2. Remove the support clip holding wire (2) to the cylinder block. Disconnect wire (2) at the connector. Upon installation, the connector must pull into the receptacle using the Allen screws.

What does FMI code 11 on a Caterpillar engine mean?