What causes the IMRC on a Ford P2004?

P2004 FORD Possible Causes Intake Manifold Runner Control (IMRC) monitor signal shorted to power Faulty Intake Manifold Runner Control (IMRC) actuator Faulty Intake Manifold Runner Control (IMRC) solenoid Damage Powertrain Control Module (PCM) Blocked vacuum hoses

How to test the IMRC module in a Ford master?

Ford master You can test the IMRC actuator by manually operating the throttle (engine running) and then watch the actuator. I open the throttle like on hard acceleration and then let off. Let me know if the rods are attached to the actuator and the shaft in the manifold.

What is the intake manifold runner control ( IMRC )?

The Intake Manifold Runner Control (IMRC) is an electrically actuated system consisting of a motorized actuator with an attaching linkage for each housing on each bank. The linkage attaches to the housing butterfly plate levers. Each IMRC housing is an aluminum casting with two intake air passages for each cylinder.

What do you need to know about the Ford Focus?

Component Testing 700-09-00-1. . . . . . . . . . . . . . The illustrations, technical information, data and descriptive text in this issue, to the best of our knowledge, were correct at the time of going to print. The right to make changes at any time, without notice, is reserved as part of Ford’s policy of continuous development and improvement.

What does it mean when IMRC is stuck in bank 1?

This code means the IMRC or Intake Manifold Runner Control is stuck in the open position in Bank 1. This trouble code is a generic trouble code, which means it applies to all vehicles made since 1996 up to present, especially those equipped with OBD-II system.

What was the code for the P2004 intake manifold runner?

2009 Doge Journey SE, 2.4L V4 with 87000 miles Code 1 � p2004 “Intake Manifold Runner Control Stuck Open Bank 1” – I replaced the intake manifold runner control valve. It was relatively easy. 3 bolts and 1 connector.

What does OBD-II scanner error code P2004 mean?

You simply need to have the right tool to read the code. If you get an OBD-II scanner error code P2004 problem that means the intake manifold runner control actuator is stuck in the open position. This simple guide will explain exactly what that means and what you should do about it. What Does P2004 Mean?

What does the code P2004 mean on a car?

What does code P2004 mean? Code P2004 stands for Intake Manifold Runner Control Stuck Open Bank 1. The intake manifold directs air into the engine via a series of runners. To improve engine performance, many late-model vehicles use what’s referred to as an intake manifold runner control (IMRC) system.

What does Bank 1 Bank 2 bank P2004 mean?

Bank 1 refers to the side of the engine with the #1 cylinder, whereas bank 2 refers to the side of the engine with the #2 cylinder. Inline engines, have only one bank – bank 1. Code P2004 is typically caused by one of the following: Sometimes P2004 can pop up in error. Clear the code and see if it returns.

When is the P2004 intake manifold runner control set?

The P2004 is set when the Intake Manifold Runner Control (IMRC) is commanded closed by the Powertrain Control Module (PCM), but the IMRC indicates open. P2004 FORD Possible Symptoms Engine Light ON (or Service Engine Soon Warning Light) P2004 FORD Meaning

What causes intake manifold runner control ( IMRC ) to shorted?

What does the P2004 Ford engine light mean?

Engine Light ON (or Service Engine Soon Warning Light) P2004 FORD Meaning The Intake Manifold Runner Control (IMRC) is an electrically actuated system consisting of a motorized actuator with an attaching linkage for each housing on each bank. The linkage attaches to the housing butterfly plate levers.

What causes an intake manifold runner to be stuck open?

If you suffer from a intake manifold runner control that is stuck open, there are a few symptoms you will probably notice. Chances are that at least one of your cylinders is not firing, which can be quite easy to recognize. The three symptoms this might cause are:

Is there a problem with the Ford Mondeo indicator?

It is over it’s 3year warranty but under 60k miles so I guess Ford won’t help 🙂 2 weeks later… sounds more like a bad switch to be honest, the microswitch in the stalk is probably the erroneous part. 10 months later… In the last week the Indicator has developed a weird problem where the Right indicator will randomly stop working.

How does the IMRC housing work on a Ford?

The linkage attaches to the housing butterfly plate levers. Each IMRC housing is an aluminum casting with two intake air passages for each cylinder. One passage is always open, and the other is opened and closed with a butterfly valve plate. The housing uses a return spring to hold the plates closed.

What to do if your Mondeo engine malfunctions?

You need to either buy a code scanner (cheap on Amazon) or get someone to read the code (s). A good bet will be the EGR valve playing up. On the mk3, it is an easy job to replace, not sure on the mk4 though.

Where is the sensor on a Mondeo 2.0?

The sensor is on the front edge of the head. A diagnostic plug in may help, but codes not guaranteed. The car is going into limp mode to protect the engine. You need to either buy a code scanner (cheap on Amazon) or get someone to read the code (s). A good bet will be the EGR valve playing up.

Why is my Mondeo business edition losing power?

I have a 2012 Mondeo 2.0 Diesel Business Edition and was getting a loss of power to start with when driving off which was probably “Limp Home Mode” and the display would say Engine Malfunction. It would also be prone to stall easily.

P2008 Ford Description The Intake Manifold Runner Control (IMRC) is an electrically actuated system consisting of a motorized actuator with an attaching linkage for each housing on each bank. The linkage attaches to the housing butterfly plate levers. Each IMRC housing is an aluminum casting with two intake air passages for each cylinder.

What causes an intake manifold code of P2004?

Code P2004 is typically caused by one of the following: A failed IMRC actuator A problem with the intake manifold or linkage Wiring issues

What causes the IMRC on a Ford P2004?